User’s Guide
L1742P
L1942P
L1742PP
L1942PP
L1742PQ
L1942PQ
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release of
heat generated during operation. If these openings are blocked, built-up heat can
cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Main power breaker is the power cord and this breaking device must be located at
a location where it is easy to operate.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
Leaving a fixed image on the screen for a long time may cause damage to the
screen and cause image burn-in. Make sure to use a screen saver on the monitor.
This phenomenon occurs to products by other manufacturers as well, and this
occurrence is not subject to warranty.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
A2
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand
1
Place the monitor with its front facing downward on a cushion or soft cloth.
Assemble the Stand Base into the Stand Body.
2.
.
Be sure don't pull out the Stop Pin and make the Stand Base direction as shown.
Stand Base
Stand Body
Side
Stop Pin
FRONT
3
.
Make the monitor stand , then pull out the Stop Pin.
The tape and locking pin may only be removed from those monitors
equipped with a standing base when the base is pulled up. Otherwise,
you may be injured by the protruding sections of the stand.
Warning:
pull out the stop pin
Stop Pin
Stop Pin
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
A3
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Positioning your display
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range: -6˚~17˚
-6
17
Height Range: maximum 4.33 inch (110.0 mm)
110.0 mm
First, remove
the locking pin.
Landscape & Portrait: You can rotate the panel 90˚ clockwise.
( For detailed information, please refer to the Pivot Software CD provided.)
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
A4
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Positioning your display
Using the cable holder
1
3
2
If you want to use the cable holder to let your cables together, please put them through
right as shown. For if you don't do like that, you cannot use Pivot function smoothly.
A5
Connecting the Display
Using the Computer
1. Make sure to turn off the computer and product. Connect the cable as below sketch map
form
to
.
1
2
A
B
C
Connect DVI Cable
Connect Dsub Cable (PC)
Connect Dsub Cable (Mac)
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your display may differ from the view as shown.
User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain standard
compliance for the product.
Analog signal
D-sub
Digital signal
DVI
Power Cord
Wall-outlet type
PC-outlet type
Mac adapter
For Apple Macintosh use, a separate plug
adapter is needed to change the 15 pin high
density (3 row) D-sub VGA connector on the
supplied cable to a 15 pin 2 row connector.
DVI-D (This feature is not available in all countries.)
2. Press
button on the front switch panel to turn the
power on. When monitor power is turned on, the
'Self Image Setting Function' is executed automatically.
(Only Analog Mode)
NOTE
‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual
input signals.
‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted
screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve
resolution.
A6
Control Panel Functions
Front Panel Controls
MENU
AUTO/SET
ENGINE SOURCE
Control
Function
Use this button to enter or exit from the On Screen Display.
MENU Button
OSD LOCKED/UNLOCKED
This function allows you to lock the current control settings, so
that these settings are not inadvertently changed. To lock the
OSD settings, press and hold the MENU button for several
seconds. The message "OSD LOCKED" appears.
You can unlock the OSD settings at any time by
pushing the MENU button for several seconds. The
message "OSD UNLOCKED" appears.
A7
Control Panel Functions
Control
Function
Use these buttons to select or adjust functions in the
On Screen Display.
Buttons
For more information, refer to page A15.
Use this button to make D-Sub or DVI connector
active. This feature is used when two computers are
connected to the display. The default setting is D-Sub.
Use this button to select an icon in the On Screen
Display.
AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SET button prior to entering the On
Screen Display(OSD). This will automatically adjust
your display image to the ideal settings for the
current screen resolution size (display mode).
The best display mode is:
17 inch: 1280x1024
19 inch: 1280x1024
Power Button
Use this button to turn the display on or off.
This Indicator lights up as blue when the display is
operating normally(On Mode). If the display is in
Sleep Mode (Energy Saving), this indicator changes
to flicker.
Power Indicator
A8
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system.
A short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the
or Buttons. When the icon you want
becomes highlighted, press the AUTO/SET Button.
Use the
/
Buttons to adjust the image to the desired level. Use the
AUTO/SET Button to select other sub-menu items.
Push the MENU Button once to return to the main menu to select another
function. Push the MENU Button twice to exit from the OSD.
A9
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment,
and setting menus.
NOTE
The order of icons may differ depending on the model (A10~A15 ).
A10
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the MENU Button, then the main menu of the OSD appears.
PICTURE
COLOR
TRACKING
SETUP
Main Menu
MENU
SET
: Exit
: Adjust (Decrease/Increase)
: Enter
: Select another sub-menu
: Restart to select sub-menu
Button Tip
Menu Name
Icons
Sub-menus
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
A11
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
PICTURE
PICTURE
To adjust the brightness of the screen.
To adjust the contrast of the screen.
BRIGHTNESS
CONTRAST
GAMMA
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
COLOR
COLOR
• sRGB: Set the screen color to fit the
SRGB standard color
PRESET
specification.
• 6500K: Slightly reddish white.
• 9300K: Slightly bluish white.
Set your own red color levels.
Set your own green color levels.
Set your own blue color levels.
RED
GREEN
BLUE
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
A12
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
TRACKING
TRACKING
To move image left and right.
To move image up and down.
HORIZONTAL
VERTICAL
To minimize any vertical bars or
stripes visible on the screen
background.
CLOCK
The horizontal screen size will also
change.
PHASE
To adjust the focus of the display.
This item allows you to remove
any horizontal noise and clear or
sharpen the image of characters.
MENU : Exit
: Decrease
To adjust the clearness of the
screen.
SHARPNESS
: Increase
SET : Select another sub-menu
A13
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
SETUP
SETUP
To choose the language in which the
control names are displayed.
LANGUAGE
OSD
To adjust position of the OSD window
on the screen.
POSITION
If the output of the video card is different
the required specifications, the color
level may deteriorate due to video
signal distortion. Using this function, the
signal level is adjusted to fit into the
standard output level of the video card
in order to provide the optimal image.
Activate this function when white and
black colors are present in the screen.
WHITE
BALANCE
Use this function to set the power
indicator on the front side of the monitor
to ON or OFF.
POWER
INDICATOR
MENU : Exit
: Adjust
: Adjust
If you set OFF, it will go off.
SET : Select another sub-menu
If you set ON at any time, the power
indicator will automatically be turned on.
Restore all factory default settings except
FACTORY
RESET
"LANGUAGE."
Press the
,
buttons to reset immediately.
If this does not improve the screen image, restore the factory default settings.
If necessary, perform the white balance function again. This function will be enabled only when
the input signal is an analog signal.
A14
On Screen Display(OSD) Selection and Adjustment
The OSD screen will appear when you touch the
the monitor.
button on the left bottom of
Menu Name
Icons
Sub-menu Name
Main menu
Sub menu
Description
IMNTOEVRNIEET This feature lets you easily select the best desired
image condition optimized to the environment
(ambient illumination, image types etc).
MOVIE: For animation images in videos or movies
INTERNET: For text images (Word processing etc.)
USER User
You can manually adjust brightness, ACE or RCM.
You can save or restore the adjusted value even
when using a different environment.
...
(Brightness): Adjusts screen brightness.
...
ACE(Adaptive Clarity Enhancer): Selects the clarity mode.
...
RCM(Real Color Management): Selects the color mode.
0
Not applied
1
Green enhance
2
Flesh tone
3
Color Enhance
SAVE
Select the
sub-menu using the AUTO/SET
button and save the YES value using the
,
buttons.
NORMAL This is under normal operating conditions.
This is just for advertising to customer in the
DEMO
shops. It’s setting is same with Movie mode and
screen is divided by half.
A15
Troubleshooting
Check the following before calling for service.
No image appears
● Is the power cord of the
•
•
•
Check and see if the power cord is connected
properly to the power outlet.
display connected?
● Is the power indicator
Press the Power button.
light on?
Adjust the brightness and the contrast.
● Is the power on and the
power indicator blue or
green?
● Is the power indicator
•
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
flicking?
• Try to turn on the PC
.
•
This message appears when the signal from the
● Do you see an "OUT OF
RANGE" message on
the screen?
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
•
This message appears when the signal cable
between your PC and your display is not
● Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?
connected. Check the signal cable and try again.
Do you see a "OSD LOCKED" message on the screen?
●
Do you see “OSD
LOCKED” when you
push MENU button?
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENU button for several
seconds: the message
“OSD UNLOCKED” will appear.
A16
Troubleshooting
Display image is incorrect
● Display Position is
•
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position icon
in the on screen display.
incorrect.
•
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in
the on screen display.
● On the screen
background, vertical
bars or stripes are
visible.
•
•
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
● Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
Important
Check Control Panel --> Display --> Settings and see if the frequency or the
resolution were changed. If yes, readjust the video card to the recommend
resolution.
The setting method can differ by computer and O/S (Operation System),
and resolution mentioned above may not be supported by the video card
performance. In this case, please ask to the computer or the video card
manufacturer
.
A17
Troubleshooting
Display image is incorrect
● The screen color is
•
•
•
Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
the slot.
mono or abnormal.
Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
● The screen blinks.
•
Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Have you installed the display driver?
●
Have you installed the
display driver?
•
Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
•
Make sure to check if the video card supports
Plug&Play function.
●
Do you see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
A18
Specifications
L1742P/L1742PQ
Display
17 inches (43.2 cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Visible diagonal size: 43.2 cm
0.264 mm pixel pitch
Horizontal Freq.
Analog : 30 - 83 kHz (Automatic)
Sync Input
Digital : 30 - 71 kHz (Automatic)
56 - 75 Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green)
Digital
Vertical Freq.
Input Form
Signal Input
15 pin D-Sub Connector
Video Input
DVI - D connector (Digital)
Input Form
Max
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Analog : VESA 1280 x 1024 @75 Hz
Digital : VESA 1280 x 1024 @60 Hz
VESA 1280 x 1024 @60 Hz
Resolution
Plug&Play
Recommend
DDC 2B (Digital), DDC 2AB (Analog)
:
30 W(Typ.)
Power
On Mode
Sleep Mode
≤
1 W
Consumption
Off Mode
≤
1 W
With Stand
Without Stand
Dimensions
&Weight
Width 36.96 cm / 14.55 inches 36.96 cm / 14.55 inches
Height 40.83 cm / 16.07 inches 31.51 cm / 12.41 inches
51.83 cm / 20.41 inches
Depth 24.16 cm / 9.51 inches
5.60 cm / 2.20 inches
3.83 kg (8.51 lbs)
-6˚~17˚
Net
Tilt
Tilt Range
Power Input
AC 100-240V~ 50/60Hz 0.8A
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 90 % non-Condensing
Attached( ), Detached ( O )
Attached( ), Detached ( O )
Wall-outlet type or PC-outlet type
Stand Base
Signal cable
Power cord
NOTE
Information in this document is subject to change without notice.
A19
Specifications
L1742PP
Display
17 inches (43.2 cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Visible diagonal size: 43.2 cm
0.264 mm pixel pitch
Horizontal Freq.
Analog : 30 - 83 kHz (Automatic)
Sync Input
Digital : 30 - 71 kHz (Automatic)
56 - 75 Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green)
Digital
Vertical Freq.
Input Form
Signal Input
15 pin D-Sub Connector
Video Input
DVI - D connector (Digital)
Input Form
Max
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Analog : VESA 1280 x 1024 @75 Hz
Digital : VESA 1280 x 1024 @60 Hz
VESA 1280 x 1024 @60 Hz
Resolution
Plug&Play
Recommend
DDC 2B (Digital), DDC 2AB (Analog)
:
30 W(Typ.)
Power
On Mode
Sleep Mode
≤
1 W
Consumption
Off Mode
≤
1 W
With Stand
Without Stand
Dimensions
&Weight
Width 36.96 cm / 14.55 inches 36.96 cm / 14.55 inches
Height 40.83 cm / 16.07 inches 31.51 cm / 12.41 inches
51.83 cm / 20.41 inches
Depth 24.16 cm / 9.51 inches
5.60 cm / 2.20 inches
4.16 kg (9.24 lbs)
-6˚~17˚
Net
Tilt
Tilt Range
Power Input
AC 100-240V~ 50/60Hz 0.8A
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 90 % non-Condensing
Attached( ), Detached ( O )
Attached( ), Detached ( O )
Wall-outlet type or PC-outlet type
Stand Base
Signal cable
Power cord
NOTE
Information in this document is subject to change without notice.
A20
Specifications
L1942P/L1942PQ
Display
19 inches (48.2 cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Visible diagonal size: 48.2 cm
0.294 mm pixel pitch
Horizontal Freq.
Analog : 30 - 83 kHz (Automatic)
Sync Input
Digital : 30 - 71 kHz (Automatic)
56 - 75 Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green)
Digital
Vertical Freq.
Input Form
Signal Input
15 pin D-Sub Connector
Video Input
DVI - D connector (Digital)
Input Form
Max
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Analog : VESA 1280 x 1024 @75 Hz
Digital : VESA 1280 x 1024 @60 Hz
VESA 1280 x 1024 @60 Hz
Resolution
Plug&Play
Recommend
DDC 2B (Digital), DDC 2AB (Analog)
:
34 W(Typ.)
Power
On Mode
Sleep Mode
≤
1 W
Consumption
Off Mode
≤
1 W
With Stand
Without Stand
Dimensions
&Weight
Width 40.63 cm / 16.00 inches 40.63 cm / 16.00 inches
Height 42.27 cm / 16.64 inches 34.45 cm / 13.56 inches
53.27 cm / 20.97 inches
Depth 24.16 cm / 9.51 inches
5.84 cm / 2.30 inches
4.23 kg (9.40 lbs)
-6˚~17˚
Net
Tilt
Tilt Range
Power Input
AC 100-240V~ 50/60Hz 0.8A
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 90 % non-Condensing
Stand Base
Signal cable
Power cord
Attached( ), Detached ( O )
Attached( ), Detached ( O )
Wall-outlet type or PC-outlet type
NOTE
Information in this document is subject to change without notice.
A21
Specifications
L1942PP
Display
19 inches (48.2 cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Visible diagonal size: 48.2 cm
0.294 mm pixel pitch
Horizontal Freq.
Analog : 30 - 83 kHz (Automatic)
Sync Input
Digital : 30 - 71 kHz (Automatic)
56 - 75 Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green)
Digital
Vertical Freq.
Input Form
Signal Input
15 pin D-Sub Connector
Video Input
DVI - D connector (Digital)
Input Form
Max
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Analog : VESA 1280 x 1024 @75 Hz
Digital : VESA 1280 x 1024 @60 Hz
VESA 1280 x 1024 @60 Hz
Resolution
Plug&Play
Recommend
DDC 2B (Digital), DDC 2AB (Analog)
:
34 W(Typ.)
Power
On Mode
Sleep Mode
≤
1 W
Consumption
Off Mode
≤
1 W
With Stand
Without Stand
Dimensions
&Weight
Width 40.63 cm / 16.00 inches 40.63 cm / 16.00 inches
Height 42.27 cm / 16.64 inches 34.45 cm / 13.56 inches
53.27 cm / 20.97 inches
Depth 24.16 cm / 9.51 inches
5.84 cm / 2.30 inches
4.63 kg (10.29 lbs)
-6˚~17˚
Net
Tilt
Tilt Range
Power Input
AC 100-240V~ 50/60Hz 0.8A
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 90 % non-Condensing
Stand Base
Signal cable
Power cord
Attached( ), Detached ( O )
Attached( ), Detached ( O )
Wall-outlet type or PC-outlet type
NOTE
Information in this document is subject to change without notice.
A22
Specifications
Preset Modes (Resolution)
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
1
2
31.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.123
68.681
61.805
63.981
79.976
640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
70
70
60
75
60
75
75
60
75
75
65
60
75
3
4
5
6
7
8
9
10
11
*12
**13
* Recommend Mode
** Only Analog Mode
Indicator
LED Color
MODE
blue
flicker
Off
On Mode
Sleep Mode
Off Mode
A23
Installing the Wall mount plate
This monitor satisfies the specifications of the Wall mount plate or
the interchange device.
1. Place the monitor with its front facing downward on a soft cloth.
2. Separate the stand after firstly separating 4 screws by using a driver as figure.
3. Install the Wall mount plate.
Wall mount plate (Separate purchase)
This is stand-type or will mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more
details, which is provided when Wall mount plate is
purchased.
Kensington Security Slot
Connected to a locking
cable that can be purchased
separately at most
computer stores
A24
Digitally yours
|