Memorex MC7101 User Manual

MC7101  
User’s Guide  
CD Clock Radio with  
Dual Alarm  
Before operating this product,  
please read these instructions completely.  
INFORMATION:  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy and, if not installed and  
used in accordance with instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver  
is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
ATTENTION:  
POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE  
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISES ET POUSSER  
JUSQU’AU FOND.  
IMPORTANT SAFETY INSTRUCTIONS  
Before using the unit, be sure to read all operating  
basement; or near a swimming pool.  
instructions carefully. Please note that these are general 8. ACCESSORIES  
precautions and may not pertain to your unit. For  
example, this unit may not have the capability to be  
connected to an outdoor antenna.  
Do not place this product on an unstable cart, stand,  
tripod, bracket or table. The product may fall, causing  
serious injury and serious damage to the product. Use  
1. READ INSTRUCTIONS  
only with  
a
cart, stand, tripod, bracket or table  
All the safety and operating instructions should be read  
before the product is operated.  
recommended by the manufacturer or sold with the  
product. Any mounting of the product should follow the  
manufacturer’s instructions, and should use a mounting  
accessory recommended by the manufacturer.  
8A. An appliance and cart combination should  
be moved with care. Quick stops,  
2. RETAIN INSTRUCTIONS  
The safety and operating instructions should be retained  
for future reference.  
3. HEED WARNINGS  
All warnings on the product and in the operating  
instructions should be adhered to.  
excessive force and uneven surfaces may  
cause the appliance and cart combination  
4. FOLLOW INSTRUCTIONS  
All operating and use instructions should be followed.  
5. CLEANING  
to overturn.  
9. VENTILATION  
Slots and openings in the cabinet and in the back or  
bottom are provided for ventilation, to ensure reliable  
operation of the product and to protect it from  
overheating. These openings must not be blocked or  
covered. The openings should never be blocked by  
placing the product on a bed, sofa, rug or other similar  
surface. This product should never be placed near or  
over a radiator or heat source. This product should not  
be placed in a built-in installation such as a bookcase or  
rack unless proper ventilation is provided or the  
Unplug this product from the wall outlet before cleaning.  
Do not use liquid cleaners or aerosol cleaners. Use a dry  
cloth for cleaning.  
6. ATTACHMENTS  
Do not use attachments not recommended by the  
product's manufacturer as they may cause hazards.  
7. WATER AND MOISTURE  
Do not use this product near water–for example: near a  
bathtub, washbowl, kitchen sink or laundry tub; in a wet  
2
IMPORTANT SAFETY INSTRUCTIONS  
manufacturer's instructions have been adhered to.  
10. POWER SOURCES  
product, ask the service technician to perform safety  
checks to determine that the product is in proper  
operating condition.  
This product should be operated only from the type of  
power source indicated on the marking label. If you are 20. WALL OR CEILING MOUNTING  
not sure of the type of power supply to your home,  
consult your appliance dealer or local power company.  
The product should be mounted to a wall or ceiling only  
as recommended by the manufacturer.  
For products intended to operate from battery power, or 21. DAMAGE REQUIRING SERVICE  
other sources, refer to the operating instructions.  
11. GROUNDING OR POLARIZATION  
Unplug the product from the wall outlet and refer  
servicing to qualified service personnel under the  
following conditions:  
a. When the power-supply cord or plug is damaged.  
b. If liquid has been spilled or objects have fallen into the  
product.  
This product is equipped with a polarized alternating-  
current line plug (a plug having one blade wider than the  
other). This plug will fit into the power outlet only one  
way. This is a safety feature. If you are unable to insert  
the plug fully into the outlet, try reversing the plug. If the  
plug should still fail to fit, contact your electrician to  
replace your obsolete outlet. Do not defeat the safety  
purpose of the polarized plug.  
c. If the product has been exposed to rain or water.  
d. If the product does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions, as an adjustment  
of other controls may result in damage and will often  
require extensive work by a qualified technician to  
restore the product to its normal operation.  
e. If the product has been dropped or the cabinet has been  
damaged.  
12. POWER-CORD PROTECTION  
Power-supply cords should be routed so that they are  
not likely to be walked on or pinched by items placed  
upon or against them, paying particular attention to  
cords at plugs, convenience receptacles, and the point  
where they exit from the appliance.  
f. When the product exhibits  
a
distinct change in  
13. LIGHTNING  
performance–this indicates a need for service.  
To protect your product from a lightning storm, or when 22. HEAT  
it is left unattended and unused for long periods of time,  
unplug it from the wall outlet and disconnect the antenna  
or cable system. This will prevent damage to the product  
due to lightning and power-line surges.  
The product should be situated away from heat sources  
such as radiators, heat registers, stoves or other  
products (including amplifiers) that produce heat.  
23. NOTE TO CATV SYSTEM INSTALLER  
14. POWER LINES  
This reminder is provided to call the CATV system  
installer's attention to Article 820-40 of the NEC that  
provides guidelines for proper grounding and, in  
particular, specifies that the cable ground shall be  
connected to the grounding system of the building, as  
close to the point of cable entry as practical.  
An outside antenna system should not be located in the  
vicinity of overhead power lines or other electric light or  
power circuits, or where it can fall into such power lines  
or circuits. When installing an outside antenna system,  
extreme care should be taken to keep from touching  
such power lines or circuits as contact with them might 24. OUTDOOR ANTENNA GROUNDING  
be fatal.  
If an outside antenna is connected to the product, be  
15. OVERLOADING  
sure the antenna system is grounded so as to provide  
some protection against voltage surges and built-up  
static charges. Section 810 of the National Electric  
Code, ANSI/NFPA 70, provides information with respect  
to proper grounding of the mast and supporting  
structure, grounding of the lead-in wire to an antenna  
discharge product, size of grounding conductors,  
location of antenna discharge product, connection to  
grounding electrodes and requirements for grounding  
electrodes.  
Do not overload wall outlets and extension cords as this  
can result in a risk of fire or electric shock.  
16. OBJECT AND LIQUID ENTRY  
Never push objects of any kind into this product through  
openings as they may touch dangerous voltage points  
or short out parts that could result in fire or electric  
shock. Never spill or spray any type of liquid on the  
product.  
17. SERVICING  
Do not attempt to service this product yourself as  
opening or removing covers may expose you to  
dangerous voltage or other hazards. Refer all servicing  
to qualified service personnel.  
ANTENNA  
LEAD IN  
WIRE  
GROUND  
CLAMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
18. REPLACEMENT PARTS  
When replacement parts are required, be sure the  
service technician uses replacement parts specified by  
the manufacturer or those that have the same  
characteristics as the original part. Unauthorized  
substitutions may result in fire, electric shock or other  
hazards.  
ELECTRIC  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
NEC  
S2898A  
-
NATIONAL ELECTRICAL CODE  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
19. SAFETY CHECK  
Upon completion of any service or repairs to this  
3
Dear Customer:  
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your  
musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement  
your equipment offers. This manufacturer and the Electronic Industries Association’s  
Consumer Electronics Group want you to get the most out of your equipment by playing it at a  
safe level. One that lets the sound come through loud and clear without annoying blaring or  
distortion—and, most importantly, without affecting your sensitive hearing.  
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of  
sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard  
against this by setting your equipment at a safe level BEFORE your hearing adapts.  
To establish a safe level:  
• Start your volume control at a low setting.  
• Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.  
Once you have established a comfortable sound level:  
• Set the dial and leave it there.  
Taking a minute to do this now will help to prevent hearing damage or loss in the future. After  
all, we want you listening for a lifetime.  
We Want You Listening For A Lifetime  
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since  
hearing damage from loud noise is often undetectable until it is too late, this manufacturer and  
the Electronic Industries Association’s Consumer Electronics Group recommend you avoid  
prolonged exposure to excessive noise. This list of sound levels is included for your protection.  
Decibel  
Level  
30  
Example  
Quiet library, soft whispers  
40  
Living room, refrigerator, bedroom away from traffic  
Light traffic, normal conversation, quiet office  
Air conditioner at 20 feet, sewing machine  
Vacuum cleaner, hair dryer, noisy restaurant  
Average city traffic, garbage disposals, alarm clock at two feet  
50  
60  
70  
80  
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE:  
90  
Subway, motorcycle, truck traffic, lawn mower  
Garbage truck, chain saw, pneumatic drill  
Rock band concert in front of speakers, thunderclap  
Gunshot blast, jet engine  
100  
120  
140  
180  
Rocket launching pad  
Information courtesy of the Deafness Research Foundation.  
EIA  
EST. 1924  
We  
WantYou  
LISTENING  
ForALifetime  
4
LOCATION OF CONTROLS  
FRONT  
1. TIME Button  
2. HOUR Button  
3. MIN (Minute) Button  
4. CD DOOR OPEN  
Switch  
5. Display DIM Button  
6. ALARM 1 Button  
7. Tune/Skip/Search m  
Button  
8. STOP (I)/OFF Button  
9. SNOOZE/SLEEP  
Button  
10. Play/Pause ®p)/CD/  
(
Power On Button  
11. Tune/Skip/Search l  
Button  
REAR  
12. Display  
13. ALARM 2 Button  
14. AM/FM/Power On  
Button  
15. VOLUME Down Button  
16. VOLUME Up Button  
17. PROGRAM Button  
18. CD MODE Button  
19. Left Speaker  
20. Right Speaker  
21. PRESETS Button  
22. SEEK Button  
23. FM Antenna Wire  
24. Stand  
25. LINE IN Jack  
26. DC 6V IN Jack  
Z
27. Battery Compartment  
(Bottom of Unit)  
28. Headphones Jack  
5
INSTALLATION  
AC ADAPTER CONNECTION  
Connect the AC adapter (included) to an AC outlet having 120V, 60Hz AC only.  
Plug the small end into the DC jack on the rear of the unit.  
CAUTION: Do not touch the AC adapter with wet hands. Fully insert the plug  
without exposing any part of the blade.  
DC 6V  
Z
INSERTING BATTERIES  
Two (2) “AAA” size batteries can also be used to power and/or to provide a backup  
for the clock and alarm time for this unit as follows:  
1. Open the battery door by pushing in on the tabs, then removing the door.  
2. Insert two (2) “AAA” batteries as shown. Alkaline batteries are recommended  
for the longest playing time.  
3. Place the battery door back on the compartment.  
NOTE: The batteries are used to back-up the clock, alarm time and radio preset  
memories when the AC adapter is disconnected or there is a power failure.  
+ –  
+
BATTERY PRECAUTIONS  
Follow these precautions when using batteries in this device:  
1. Use only the size and type of batteries specified.  
2. Be sure to follow the correct polarity when installing the batteries as indicated in the  
battery compartment. Reversed batteries may cause damage to the device.  
3. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and  
Carbon-zinc) or old batteries with fresh ones.  
4. If the device is not to be used for a long period of time, remove the batteries to  
prevent damage or injury from possible battery leakage.  
5. Do not try to recharge batteries not intended to be recharged; they can overheat and  
rupture. (Follow battery manufacturer’s directions.)  
BACKLIGHT  
If the power supply is connected to the DC 6V IN jack, the backlight will always  
light on in the display.  
6
OPERATION  
TO LISTEN TO THE RADIO  
1
2
2
1
MANUAL TUNING: Repeatedly press  
the Tune/Skip/Search l 1 or m 2  
button to manually advance the  
frequency in the display up or down  
until the desired frequency appears.  
The display will revert back to the time  
display after five seconds.  
Press the AM/FM/Power On button to  
turn the unit on and select radio.  
Repeatedly press the AM/FM/Power  
On button to select AM or FM.  
3
4
2
1
2
AUTOMATIC TUNING: Press and hold Adjust the VOLUME Up/Down buttons  
the Tune/Skip/Search l 1 or m 2 1 as desired.  
To turn the unit off, press the STOP  
(I)/OFF button 2.  
button until the frequency in the display  
starts to scan, and then release the  
button; the tuner will search and then  
stop on the next strong station it finds.  
Repeat this step until the desired  
frequency appears in the display. The  
display will revert back to the time  
display after five seconds.  
Antennas  
FM: Unravel and extend the FM antenna wire for best reception.  
AM: Turn the unit for better AM reception.  
7
OPERATION (CONTINUED)  
RADIO PRESETS–Up to 9 AM and 9 FM  
1
2
2
Select a station using the Tune/Skip/  
Search l 1 or m 2 button. Press the  
PROGRAM button 3; the preset  
number will blink in the display. Within  
three seconds, press the PRESETS  
button 4 until the desired memory  
number appears in the display.  
Press the AM/FM/Power On button to  
turn the unit on and select radio.  
Repeatedly press the AM/FM/Power  
On button to select AM or FM.  
3
4
Press the PROGRAM button again to Repeat steps 2 and 3 to program up to  
9 stations in each band, if desired.  
TO RECALL: Follow step 1 above.  
Repeatedly press the PRESETS  
button to select a preset; the station  
will automatically be tuned in.  
set the station in the selected  
memory.  
NOTE: See the next page for Automatic Preset Seek.  
8
OPERATION (CONTINUED)  
AUTOMATIC PRESET SEEK  
To have the unit automatically seek through the radio stations and program the  
first 9 strong stations, perform the steps as follows:  
1
2
2
1
Press the SEEK button 1; the unit will  
then seek through all of the radio stations  
and program the first 9 strong stations.  
When done, it will stop on the first preset.  
Press the PRESETS button 2 repeatedly  
to select a preset station.  
Press the AM/FM/Power On button to  
turn the unit on and select radio.  
Repeatedly press the AM/FM/Power  
On button to select AM or FM.  
INSERTING A CD  
1
Slide the CD DOOR OPEN switch to  
the right and the CD door will open.  
Gently insert a CD onto the spindle  
(label side facing forward) until it  
clicks. Close the CD door.  
FAQS: Do I need an adapter to play 3” singles?  
No, simply insert the 3” single into the groove.  
What is the maximum time for a CD in this unit?  
The maximum time is 74 minutes.  
9
OPERATION (CONTINUED)  
TO PLAY A CD  
1
2
With a CD inserted (see previous If in the Stop mode, press the Play/  
page), press the Play/Pause ®p)/CD/ Pause (®p)/CD/Power On button to  
(
Power On button to turn the unit on start  
playback.  
TO  
PAUSE  
and select CD; playback will start PLAYBACK, press the Play/Pause  
automatically.  
(®p)/CD/Power On button again; the  
elapsed track time will blink in the  
display. Press again to resume  
playback.  
3
4
2
1
2
To skip forward or backward through the  
tracks on the disc, press the Tune/Skip/  
Search l 1 or m 2 button. To search  
forward or backward through the tracks  
on the disc, press and hold the Tune/  
Skip/Search l 1 or m 2 button.  
Adjust the VOLUME Up/Down buttons  
1 as desired. When the disc is through  
playing, it will stop. Press the STOP  
(I)/OFF button 2 to stop the disc before  
it is finished. Press the STOP (I)/OFF  
button 2 again to turn the unit off.  
NOTES:  
If a disc is inserted incorrectly, dirty, damaged or not present at all, the display will  
show, "no disc" for 5 seconds. Then, "no" and the actual time will appear in the display.  
When you press the Tune/Skip/Search l or m button, the track elapsed time will  
appear for three seconds then revert back to the time display.  
While playing a CD, press the TIME button to show the elapsed time briefly in the  
display. When you press the TIME button, the CD playback track's elapsed time will  
appear in the display for five seconds and then revert back to the time display.  
10  
OPERATION (CONTINUED)  
TO REPEATEDLY PLAY BACK ONE TRACK  
1
2
2
1
With a CD inserted (see page 9), press  
Press the Tune/Skip/Search l 1 or m  
2 button to select a track to repeat.  
the Play/Pause ®p)/CD/ Power On  
(
button to turn the unit on and select  
CD; playback will start automatically.  
TO REPEATEDLY PLAY BACK ALL  
TRACKS  
3
2
1
1
2
1
Press the CD MODE button 1 once;  
“REPEAT” will appear in the display and  
the unit will play the same track over  
and over until the STOP (I)/OFF  
Follow step 1 above. Press the CD  
MODE button 1 twice; “REPEAT ALL”  
will appear in the display and the unit  
will play all the tracks on the CD over  
and over until the STOP (I)/OFF  
button 2 is pressed.  
button 2 is pressed.  
TO CANCEL REPEAT MODE, press the CD MODE button four times.  
TO CANCEL REPEAT ALL MODE, press the CD MODE button three  
times.  
11  
OPERATION (CONTINUED)  
TO PROGRAM THE MEMORY (UP TO 20 TRACKS)  
1
2
2
1
3
2
1
With a CD inserted (see page 9), press  
Press the PROGRAM button 1 once; “P  
01” (program number), “00” track number  
and the Program indicator will appear in  
the display. Select the first track to be  
played back using the Tune/Skip/Search  
l 2 or m 3 button, then press the  
PROGRAM button 1 again. Repeat this  
step to program additional tracks, up to  
20 tracks.  
the Play/Pause ®p)/CD/ Power On  
(
button to turn the unit on and select CD;  
playback will start automatically. Press  
the STOP (I)/OFF button 2 to stop  
automatic playback.  
3
4
2
Press the PLAY/PAUSE (®p)/CD/ Adjust the VOLUME Up/Down buttons 1  
Power On button to begin playback. as desired. When the disc is through  
The unit will play all the tracks in the playing, it will stop. Press the STOP  
order you programmed them.  
(I)/OFF button 2 to stop the disc before  
it is finished.  
NOTES:  
To skip forward or backward through the programs, press the Tune/Skip/  
Search l or m button.  
Programming is the ability to preselect the order in which a series of tracks will  
be played.  
FAQ:  
How do I clear the memory and exit the Program Playback mode?  
While in the Program Stop mode, press the STOP (I)/OFF button; the  
"PROGRAM" indicator will disappear from the display.  
12  
OPERATION (CONTINUED)  
RANDOM PLAYBACK  
1
2
1
2
To play the tracks on the CD in a  
random order, while in the Stop mode,  
press the CD MODE button three  
times; “RANDOM” will appear in the  
display.  
Press the PLAY/PAUSE (®p)/CD/  
Power On button 1; the unit will  
randomly play each track on the CD  
and then stop. If you want to randomly  
playback the tracks repeatedly, press  
the CD MODE button 2 once more;  
“REPEAT ALL RANDOM” will appear  
in the display.  
TO CANCEL RANDOM MODE, press the CD MODE button twice.  
TO CANCEL REPEAT ALL RANDOM MODE, press the CD MODE button once.  
TO STOP PLAYBACK, press the STOP (I)/OFF button.  
HEADPHONES Jack  
For private listening, plug headphones (not supplied) into the Headphones jack on the rear of  
the unit. When the headphones are plugged in, the speakers will be muted.  
LINE IN Jack  
By using a home audio connection cable (not included), you can listen to an external audio unit  
through this unit’s speakers. Before making any connections, turn off the power to all equipment.  
Press the AM/FM/Power On button or the PLAY/PAUSE (®p)/Power On button to turn the unit  
to CD or Radio mode. Plug a connection cable (not included) between the LINE OUT jack on  
the external audio unit and this unit's LINE IN jack (rear of the unit). (Do not connect it to this  
unit's Headphone jack.) Then the unit will automatically turn to the AUX mode and the "AUX"  
indicator will appear in the display. Turn on the external audio unit and start playback; the  
external unit's output sound will be heard through this unit's speakers. Press the Volume  
Up/Down button to adjust the volume level as desired.  
To turn the unit off, remove the plug from the LINE IN jack, then press the STOP (I)/OFF button.  
NOTE: If you are in Radio/CD mode, when you connect an external unit to the LINE IN jack, this  
unit will automatically switch to AUX mode. If you remove the plug from the LINE IN jack, the unit  
will resume to the mode it was in before the external unit was connected.  
13  
OPERATION (CONTINUED)  
TO SET OR RESET THE ACTUAL TIME  
1
2
2
1
With the power off, press the TIME  
button; the time will blink.  
Press the MINUTE button 1 to set  
the present minute and the HOUR  
button 2 to set the present hour.  
Make sure to set the correct AM/PM  
setting.  
3
Press the TIME button (or wait  
approx. 15 seconds) and the time will  
be set.  
14  
OPERATION (CONTINUED)  
TO SET OR RESET THE ALARM TIME  
1
2
1
2
4
1
2
With the power off, press the desired ALARM  
1 1 or ALARM 2 2 button; the Alarm 1 or  
Alarm 2 time and settings will appear.  
Press and hold the desired ALARM 1 1 or  
ALARM 2 2 button; the alarm time will blink.  
Press the MINUTE button 3 to set the alarm  
minute and the HOUR button 4 to set the  
alarm hour. Make sure to set the correct  
AM/PM setting. Press the ALARM 1 1 or  
ALARM 2 2 button again (or wait approx. 15  
seconds); the alarm time will stop blinking.  
4
3
1
2
2
1
If set to CD, within 5 seconds, set the track number  
using the Tune/Skip/Search l 1 or m 2 button. When  
the alarm time is reached, the unit will start playback  
on the track that you selected and the tracks following  
it, then stop.  
Repeatedly press the ALARM 1 1 or ALARM  
2 2 button to select alarm off, alarm on for  
buzzer, radio or CD.  
NOTE: Make sure the corresponding  
indicator (BUZZER/CD/RADIO) appears in  
the display.  
NOTES:  
When you have selected a track number, after five  
seconds, the track number will be set and the  
actual time will appear in the display again.  
If the selected track is not available (i.e. there are a  
total of 10 tracks on the disc but you have selected  
track 11), when the alarm time is reached,  
playback will start from the first track.  
If set to Radio, within 5 seconds, set the band (AM or  
FM) and the frequency using the Tune/Skip/Search l  
1 or m 2 button. When the alarm time is reached, the  
unit will turn on the band (AM or FM) and the  
frequency that you selected.  
NOTE: When you have selected the radio band and  
frequency, after 5 seconds, the radio frequency will be  
set and the actual time will appear in the display again.  
SEE NEXT PAGE FOR IMPORTANT ALARM NOTES.  
15  
OPERATION (CONTINUED)  
NOTES:  
It is not necessary to set the volume level for the alarm. When the alarm  
time is reached, the alarm volume level will be set to the default (Medium  
Level) and it will increase one step every five seconds continuously until the  
maximum volume level is reached.  
When the actual time matches the selected preset alarm time(s), if set to  
Radio or Buzzer, the unit will automatically turn on for 20 minutes and then  
shut off. If set to CD, the unit will only play the tracks on the CD and then  
shut off. If you select a starting track for the alarm, the unit will only playback  
the selected track and the tracks following it and then shut off.  
TO SHUT OFF THE ALARM, see TO SHUT THE ALARM OFF section on  
the next page.  
While the alarm is sounding, if the other alarm reaches the alarm time, the  
first alarm will stop sounding and the second alarm will start sounding.  
Make sure you have disconnected the headphones from the Headphones  
jack (rear of the unit) and disconnected the audio cable from the LINE IN  
jack (rear of the unit); otherwise, there will be no sound when the actual time  
matches the preset alarm time.  
16  
OPERATION (CONTINUED)  
TO SHUT THE ALARM OFF  
To shut the alarm off, press the desired ALARM 1 1 or  
1
ALARM 2 2 button and the alarm time will be reset for  
the next day. Press the desired ALARM 1 1 or ALARM  
2 2 button repeatedly until the alarm time and the  
ALARM 1 or ALARM 2 indicator disappears from the  
display to turn off the alarm and not set it for the next  
day.  
1
2
SNOOZE AND SLEEP  
SNOOZE: While the alarm is sounding, press the  
SNOOZE/SLEEP button; the SNOOZE indicator will appear in the  
display. Also, "10" will appear in the display for five seconds and  
then revert back to the actual time. The alarm will turn back on  
automatically ten minutes later. OR While the alarm is sounding,  
press and hold the SNOOZE/SLEEP button. Keep holding the  
button for approx. one second, "10" will appear in the display  
indicating the alarm will turn back on after 10 minutes. Continue  
holding the button for one more second, "15" will appear in the  
display indicating the alarm will turn back on after 15 minutes.  
Continue holding the button to set the SNOOZE time to "20", "25",  
"30", etc., up to "60". Please note that once you release the button,  
the time shown on the display will be the SNOOZE time and the  
alarm will turn back on according to the SNOOZE time set. NOTE:  
To cancel the SNOOZE function, press the STOP (I)/OFF button  
once; the SNOOZE indicator will disappear from the display.  
SLEEP: With the unit in the CD or Radio mode, press the  
SNOOZE/SLEEP button twice; "10" will appear in the display for  
five seconds which indicates the unit will turn off after 10 minutes.  
Repeatedly press the SNOOZE/SLEEP button to select the  
SLEEP time, up to 60 minutes (i.e. , "20"–turns off automatically  
after 20 minutes, "30"–turns off automatically after 30 minutes,  
etc.). After 5 seconds, the SLEEP time will disappear from the  
display. To view the remaining SLEEP time, press the  
SNOOZE/SLEEP button once. NOTE: To cancel the SLEEP  
function, repeatedly press the SNOOZE/SLEEP button until "- -"  
appears in the display. After five seconds, the actual time will  
appear again and the SLEEP indicator will disappear from the  
display.  
1
DISPLAY DIM BUTTON  
Press the Display DIM button to adjust the dimmer of  
the display. If the display is too dim, press the Display  
DIM button for a brighter display. Press the Display DIM  
button again to resume to a less bright display.  
1
17  
CARE AND MAINTENANCE  
Caring for Compact Discs  
Treat the disc carefully. Handle the disc only  
by its edges. Never allow your fingers to come  
in contact with the shiny, unprinted side of the  
disc.  
Do not attach adhesive tape, stickers, etc. to  
the disc label.  
Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents  
or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.  
If a disc skips or gets stuck on a section of the disc, it is probably dirty or  
damaged (scratched).  
When cleaning the disc, wipe in straight lines from the center of the disc to the  
outer edge of the disc. Never wipe in circular motions.  
This unit is designed to play only discs bearing the identification  
logo as shown here. Other discs may not conform to the CD  
standard and may not play properly.  
Discs should be stored in their cases after each use to avoid  
damage.  
Do not expose discs to direct sunlight, high humidity, high temperatures or dust,  
etc. Prolonged exposure or extreme temperatures can warp the disc.  
Do not stick or write anything on either side of the disc. Sharp writing  
instruments, or the ink, may damage the surface.  
Cleaning the Unit  
To prevent fire or shock hazard, disconnect your unit from the AC power source  
when cleaning.  
The finish on your unit may be cleaned with a dust cloth and cared for as other  
furniture. Use caution when cleaning and wiping the plastic parts.  
Mild soap and a damp cloth may be used on the front panel.  
18  
TROUBLESHOOTING GUIDE  
If you experience a problem with this unit, check the chart below before calling  
for service.  
SYMPTOM  
Unit will not  
turn on.  
CAUSE  
AC adapter is not  
connected.  
SOLUTION  
Check the AC adapter  
connection.  
Disc will not play.  
CD compartment  
door not closed.  
Disc inserted  
incorrectly.  
Close CD compartment  
door.  
Reinsert disc correctly.  
Dirty or defective CD. Try another disc.  
Moisture  
Wipe disc with soft cloth.  
condensation on disc.  
Volume setting is  
set to minimum.  
Defective disc.  
Dirty or defective  
disc.  
No sound.  
Increase volume.  
Try another disc.  
Clean or replace disc.  
Erratic playback.  
Time reset to “12:00”. Batteries connected  
improperly, not con-  
Check the batteries.  
nected or dead.  
Clock not set.  
Set the clock.  
Alarm does not  
turn on.  
Alarm is not activated Set and activate alarm as  
or set properly.  
Clock is not set.  
described on page 15.  
Set the clock.  
AM or FM, no sound. Power is not on.  
Press AM/FM/Power On  
button to turn the unit on.  
Increase volume.  
Volume setting is  
set to minimum.  
19  
SPECIFICATIONS  
AUDIO  
Frequency Range (AM)..................................................520–1710KHz  
Frequency Range (FM)...................................................87.5–108MHz  
CD SECTION:  
Disc Diameter................................................................4.72” (120mm)  
3.15” (80mm) Single CD  
Optical Source.....................................................Semiconductor Laser  
Wavelength ................................................................................780nm  
GENERAL  
Power Supply......................................DC IN Jack 6V, Center Positive  
Battery Backup ...................................... 2 x 1.5V “AAA” size batteries  
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT  
OUR WEB SITE AT  
WWW.MEMOREXELECTRONICS.COM  
OR CONTACT CUSTOMER SERVICE AT (954) 660-7100.  
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN  
CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR PLACE OF  
PURCHASE OR TO MEMOREX.  
FOR PARTS AND ACCESSORIES, CONTACT FOX INTERNATIONAL AT  
1-800-321-6993.  
20  
Memcorp, Inc.  
Weston, FL  
Printed in Hong Kong  

Mr Coffee FT Series User Manual
Motorola I1 User Manual
Motorola 8000202590 A User Manual
McIntosh MVP871 User Manual
Maxtor DIAMONDMAX 21 PATA STM3250820A User Manual
Lenovo M500 User Manual
Lenovo 40Y8692 User Manual
Hitachi Travelstar HTS722080K9A300 User Manual
Harbor Freight Tools 94738 User Manual
Hamilton Beach 840073500 User Manual