Kenwood KRC 977R User Manual

CASSETTE RECEIVER

KRC-PS1077R

KRC-977R

KRC-877R

KRC-877W

KRC-777R

INSTRUCTION MANUAL

Safety precautions

IMPORTANT INFORMATION

2WARNING

2CAUTION

You cannot connect the unit directly to the

following CD automatic changers. For users

who want to use older changers with the

unit, follow the directions below according to

the type of changer you own:

To prevent injury and/or fire, take the

following precautions:

• Insert the unit all the way until it is fully

locked in place. Otherwise it may fly out of

place during collisions and other jolts.

To prevent damage to the machine,

take the following precautions:

• Make sure to ground the unit to a negative

12V DC power supply.

• KDC-C200 / KDC-C300 / KDC-C400

• Do not open the top or bottom covers of the

unit.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• Do not subject the faceplate to excessive

shock, as it is a piece of precision equipment.

• When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

• To prevent short circuits when replacing a

fuse, first disconnect the wiring harness.

• Do not place any object between the

faceplate and the unit.

• During installation, do not use any screws

except for the ones provided. The use of

improper screws might result in damage to

the main unit.

Use the extension cable and the control box

attached to the CD changer, and the optional

CA-DS100 converter cable.

• KDC-C301 / KDC-C600 / KDC-C800 / KDC-

C601 / KDC-C401

Use the extension cable attached to the CD

changer, and the optional CA-DS100

converter cable.

• KDC-C100 / KDC-C302 / C205 / C705 /

non-Kenwood CD changers

• When extending the ignition, battery or

ground cables, make sure to use automotive-

grade cables or other cables with an area of

0.75mm (AWG18) or more to prevent cable

deterioration and damage to the cable

coating.

• To prevent short circuits, never put or leave

any metallic objects (e.g., coins or metal

tools) inside the unit.

• If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

• Make sure not to get your fingers caught

between the faceplate and the unit.

• Be careful not to drop the unit or subject it to

strong shock.

The unit may break or crack because it

contains glass parts.

• Do not touch the liquid crystal fluid if the LCD

is damaged or broken due to shock. The

liquid crystal fluid may be dangerous to your

health or even fatal.

Cannot be used with this model.

2CAUTION

You can damage both your unit and

the CD changer if you connect them

incorrectly.

If the liquid crystal fluid from the LCD

contacts your body or clothing, wash it off

with soap immediately.

— 3 —

Safety precautions

Mask key

Cleaning the Tape Head

NOTE

If you have transmitted the Mask Key's signal

once to the unit in advance, you will have to

transmit it once again if the unit has been

removed from the battery. This function

helps prevent theft.

When using the unit for the first time:

In order to deactivate the demonstration

mode, be sure to press the transmit button

to transmit the Mask Key's signal.

If this procedure is not carried out, the

control panel of the unit will re-open in two

seconds even with your vehicle's ignition

turned off.

After you have used the tape player many

times over a long period, magnetic powder

from the tapes and dust accumulates on the

tape head, causing noise and a deterioration

in sound quality. Clean the tape head using a

cleaning tape or cleaning kit designed for use

in car audio systems.

• If you experience problems during

installation, consult your Kenwood dealer.

Egnlish

• If the unit fails to operate properly, press the

RESET button. When the faceplate is not

visible, slide the manual open switch (as

illustrated on p.6) for as many times as you

have preset to make the faceplate control

appear. The unit returns to factory settings

when the RESET button is pressed. If the

unit still fails to operate properly after the

RESET button has been pressed, contact

your local KENWOOD dealer for assistance.

Handling Cassette Tapes

• Do not play a cassette whose tape has gone

slack. In such a case, wind it tight using a

pencil or the like in one of the spools. Playing

slack cassette tapes can result in the tape

tangling around the capstan and/or pinch

rollers, causing trouble.

• Do not play a deformed cassette or one

whose label is starting to come off, as it can

cause the unit to malfunction.

• Do not leave tapes in hot places, such as

above the fascia panel (dashboard) and other

spots exposed to direct sunlight, or near

heater outlets. They can deform the cassette.

• Avoid using extremely long cassette tapes,

such as 100-minute-long tapes. Such tapes

are very thin, and can tangle easily around

the pinch rollers or other parts inside the unit,

causing unit failure.

• Press the reset button if the CD auto changer

is first controlled and operates incorrectly.

The original operating condition will return.

2CAUTION

Do not loose the "Mask Key".

If power is disconnected from the unit,

correct operation can only be restored by the

"Mask Key's" signal.

The "Mask Key" will also be required for

service repair.

44W

DISC

EJECT

DISP

OFF

DAB

NAME.S

T I

VOL ADJ

LOUD

SCAN

B.S/RDM

REP

D.SCN

MTL/M.RDM

PROG/PTY

DISC

NOTE

If you send products in for repair that include

a mask key, make sure to present the unit

together with the mask key.

Reset button

• Characters in the LCD may become difficult

to read in temperatures below 41 ˚F (5 ˚C).

Cleaning the Unit

• Remove a cassette tape from the unit when

not listening to it for a whilst. If you leave a

tape in the unit too long, it may stick to the

tape head and cause unit malfunction.

If the front panel gets dirty, turn off the

power and wipe the panel with a dry silicon

cloth or soft cloth.

Dolby noise reduction manufactured under

license from Dolby Laboratories Licensing

Corporation.

”DOLBY” and the double-D symbol are

trademarks of Dolby Laboratories Licensing

Corporation.

2CAUTION

Do not wipe the panel with a stiff cloth or a

cloth dampened by volatile solvents such as

paint thinner and alcohol. They can scratch

the surface of the panel and/or cause the

indicator letters to peel off.

— 4 —

Basic operations

Volume

SRC

Increasing Volume:

Press the u button to turn up the volume.

44W

DISC

EJECT

Decreasing Volume:

DISP

NAME.S

OFF

Press the d button to turn down the volume.

T I

VOL ADJ

LOUD

SCAN

B.S/RDM

REP

D.SCN

MTL/M.RDM

PROG/PTY

DISC

ATT / LOUD

KRC-PS1077R/977R

LOUD indicator

ATT indicator

KRC-877R/877W/777R

LOUD indicator

ATT indicator

— 5 —

Basic operations

• Whilst the control panel is moving, pressing the buttons will not

have any effect. Do not try to press the buttons on the control

panel as the faceplate is moving, as excessive force may

damage the unit.

• During the forced closing of the unit (i.e., having the unit left

closed whilst ignition is turned on), the faceplate will not open

no matter how often the ignition is turned on or off, unless

“Manual Open Switch” at the rear of the faceplate is pressed in

order to open it. You can prevent tampering of the unit when

letting someone else drive your car by keeping it closed this

way.

Power

You can help prevent theft of the unit by reversing the faceplate

so that the control panel cannot be seen, hiding the unit, and

shutting off the audio.

Egnlish

Power ON/OFF:

When you turn your vehicle’s ignition on, the unit’s power will

also turn on, with the faceplate reversing to show the control

panel.

When you turn your vehicle’s ignition off, the faceplate will

reverse to hide the control panel, and the unit’s power will turn

off.

To cancel the forced closing of unit and open control panel:

Slide the Manual open switch, as illustrated below, for as many

times as you have preset in the "Manual Open Switch Setting

(OPEN SW#)" in the menu.

NOTE

• After installation of your Mask unit, be sure to transmit the

"Mask Key's" signal to deactivate the demonstration mode.

If this procedure is not carried out, the control panel of the unit

will re-open in two seconds even with your vehicle's ignition

turned off.

• When the control panel of the faceplate is hidden, the unit will

be locked by the sleeve, making it more difficult to remove the

unit.

NOTE

When you set the Manual Open Switch setting to 2 or 3, slide the

manual open switch successively. If you do not slide the switch

successively, this cannot be verified correctly.

• When the moving faceplate is hit by an object, it will stop and

return to its original state. Remove the object and repeat the

action.

2CAUTION

Using the Unit in Vehicles with Covered Consoles

• Make sure the console is uncovered whilst the faceplate is

reversed.

• Do not exert any excess force on the movable parts of the unit,

including the faceplate, as it can cause failure in the unit’s

mechanism.

Manual open switch

Hiding the unit with the ignition turned on (forced closing):

Hold down the SRC button for one second or more.

The faceplate will reverse, hiding the unit. The unit will turn

off.

NOTE

• When the closing faceplate is hit by an object, the unit will turn

off without the faceplate closing all the way. Remove the object

and press the SRC button to turn the unit back on, then turn it

off again to make it close properly.

— 6 —

Switching Modes

Loudness

This function amplifies low and high tones when the volume is

Switching Modes:

turned down.

Each time you press the SRC button, the mode switches as

follows:

The LOUD indicator lights up, when the loudness function is

on.

▼

Turning Loudness On/Off:

Tuner mode

▼

Hold down the LOUD button for one second or more to switch

the loudness on and off.

Tape mode

▼

External disc control mode

▼

AUX mode

NOTE

• The mode switches to the next mode from any mode which

cannot be used.

• The external disc control mode will differ depending on the unit

that is connected.

• The AUX mode is available only when the changer / AUX

switching adapter (KCA-S210A or CA-C1AX) or CD changer

(KDC-CPS82 or KDC-CX82) is connected to this unit.

During the AUX mode, "AUX" will show in the display.

When the CA-C1AX is being used, the AUX Mode will replace

the External Disc Control Mode.

Attenuator

This function allows you to turn down the volume quickly.

Turning Attenuator On/Off:

Press the ATT button to switch the attenuator on and off.

When the attenuator is on, the ATT indicator blinks.

When the attenuator is off, the volume returns to the original

level.

NOTE

Turning down the volume all the way turns off the attenuator

function.

— 7 —

Basic operations

Adjustment (Contrast ##) ↔ Dimmer (Dimmer ON / OFF)➞

Menu System

Switching Graphic Display(Graphic ON / OFF)* ↔ Black Mask

To accommodate a greater number of functions, a menu

system has been employed for making settings. Press the

MENU button to enter the menu mode and then display the

function to make the setting. Details on each setting are

explained separately in the corresponding function page.

(BLACK MASK OFF / ON, BLK MASK OFF / ON) ↔ Switching

Preout (SWPRE Rear / N-Fad)* ↔ Dual zone system* (Zone 2

Egnlish

OFF / ON)* ↔ External Amplifier Control (AMP BASS Flat, FLT

/ +6 / +12) ↔ Manual Open Switch Setting (OPEN SW #) ↔

News Bulletin Function (NEWS OFF / ##MIN) ↔ Local seek*

(Local.S OFF / ON) ↔ Selecting Tuning Mode* (Auto1 / Auto2 /

Hold down the MENU button for one second or more.

"MENU" is displayed when the menu mode is entered.

The function that you can adjust is indicated with the current

settings displayed.

Manual) ↔ Auto Memory Entry* (Auto-Memory (start)) ↔ AF

Function* (AF ON / OFF) ↔ Region Restrict Function* (REG

ON / OFF) ↔ Auto TP Seek* (ATPS ON / OFF) ↔ Monaural

Reception* (MONO OFF / ON) ↔ Text Scroll* (Scroll Manu /

Selecting function to set

Auto) ↔ Touch Sensor Tone

When Automatic Time Adjustment is off

Time adjustment mode entered

In AUX mode

Press the ¢ button to search through the functions until you

see the one you want to adjust in the display.

Press the 4 button to search through the functions

backward.

In Tuner mode

Except in AM band

In FM reception of Tuner mode

In FM or External disc control mode

KRC-PS1077R/KRC-977R Only

KRC-977R/KRC-877R/KRC-877W Only

KRC-PS1077R/KRC-977R/KRC-877R/KRC-877W Only

Example: If you want to switch the tuning mode from Auto1 to

manual, first search through the functions until you

see "Auto 1" in the display.

NOTE

• Make sure to end the menu mode when finished.

If you fail to end the menu mode, several functions may not

operate properly, including the Traffic Information function, the

News Bulletin function with PTY news timeout setting, and the

Alarm function.

• The News function turns on when the setting is made for the

news interruption interval. The "##MIN" display indicates the

setting selected for the news interruption timeout interval.

• The "##" display indicates the setting value.

Changing setting for currently displayed function

Press either the AM or FM button.

The setting will change for each function.

Example: The tuning mode will switch from Auto 1 to Auto 2.

Pressing the button again switches the setting to

manual, and "Manual" is displayed.

Ending the menu mode

Press the MENU button.

The selection includes:

Touch Sensor Tone (Beep ON / OFF) ↔ Time Adjustment*

<Manual> (Clock Adjst, Clock Adjust)* ↔ Automatic Time

Adjustment* (SYNC ON / OFF) ↔ Mask key (Mask key) ↔

Selectable Illumination (Color Green / Amber) ↔ Contrast

— 8 —

Tuner features

SRC

Selecting Tuning Mode

You can choose from three tuning modes: auto seek, preset

station seek, and manual. The “AUTO 1” indicator lights up

when auto seek tuning is selected, and the “AUTO 2” indicator

lights when preset station seek tuning is selected.

44W

DISC

EJECT

DISP

NAME.S

OFF

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

T I

VOL ADJ

LOUD

SCAN

B.S/RDM

REP

D.SCN

MTL/M.RDM

PROG/PTY

DISC

Press the ¢ button repeatedly until the tuning function

appears in the display.

Press the 4 button to search in the other direction.

The tuning method is displayed as ”Auto 1“, ”Auto 2“, or

”Manual“ referring respectively to auto seek tuning, preset

station seek tuning, and manual tuning.

#1~6

MENU AM

KRC-PS1077R/977R

Switching settings

Frequency

Press either the AM button or FM button to switch the tuning

Band display

Preset station number

mode.

The display and setting will change.

Press the MENU button to end the menu mode.

ST indicator

Mode display

AUTO indicator

Frequency

KRC-877R/877W/777R

Band display

Preset station number

AUTO indicator

Mode display

ST indicator

— 9 —

Tuner features

Tuning

Press the ¢ button repeatedly until the local seek function

appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "Local.S ON" or "Local.S

OFF" in the display, indicating that the local seek function is on

or off, respectively.

Press the SRC button repeatedly until the tuner mode is

obtained. "TUNER" is displayed only when the tuner mode is

selected.

Egnlish

Press either the FM or AM button to select the band.

Each time you press the FM button, the band switches

between the FM1, FM2 and FM3.

Switching settings

Press either the AM button or FM button.

The display and setting will change.

Press the AM button to select the MW and LW bands.

• Auto Seek Tuning

Press the MENU button to end the menu mode.

Press the ¢ button to seek increasing frequencies.

Press the 4 button to seek decreasing frequencies.

• Preset station seek tuning

Press the ¢ button to move to the next preset station (i.e.,

the one with the next highest number), and the 4 button to

move to the last preset station (i.e., the one with the next

lowest number).

Station Preset Memory

Store the frequency of the station currently being listened to.

You can then recall that station with a single touch of a button.

NOTE

Select the band/ station that you want to have stored.

If the frequencies stored at the preset numbers receive

stations which were not originally memorized when traveling

long distances, the preset number is not displayed. In such

cases, pressing the 4/¢ button to use preset station seek

will receive channel 1.

Hold down the button (#1-6) that you want to use for the

station, for two seconds or more.

The button number blinks once in the display to indicate that

the data has been stored.

• Manual Tuning

Recalling a Preset Station:

Press the ¢ button to increase the frequency by one step.

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

Press the 4 button to decrease the frequency by one step.

NOTE

The ST indicator lights up when stereo broadcasts are being

received.

You can store 6 stations in each of the FM1, FM2, FM3, and AM

(MW and LW) bands.

Local Seek Function

With the local seek function turned on, auto seek tuning skips

stations with relatively poor reception.

Auto Memory Entry

You can automatically store all the receivable frequencies in

the band currently being listened to, and then recall them with

the touch of a button later. This function is especially useful

when you are travelling and do not know what stations are

available. Up to 6 frequencies can be stored this way.

Turning Local Seek Function On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

— 10 —

Select the band for auto memory entry.

Press the DNPP button on the remote control.

“SNPP” will be displayed once the seek mode is entered.

The names of the stations preset in the band currently listened

to are displayed for 5 seconds each.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until "Auto-Memory" appears in

the display.

Press the 4 button to search in the other direction.

Hold down either the AM button or FM button for two seconds

or more to start auto memory function.

The numbers of the preset station buttons showed in order.

When all the stations in a certain band are stored in the preset

memory, the auto memory entry stops. The tuner then plays

the last station received.

The display band switches in the following order:

= FM1 Ô FM2 Ô FM3 Ô AM +

Each time you press the ¢ button, the station display

switches in the forward direction.

Each time you press the 4 button, the station display

switches in the reverse direction.

Stations which have no names will be displayed as frequencies.

NOTE

Changing the Displayed Band

Pressing the FM button switches between the FM1, FM2, FM3

Recalling a Preset Station:

and AM displays, in that order.

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

Pressing the AM button switches between the displays in the

reverse direction.

NOTE

Once the name is displayed for the station you want to listen

• When the AF function is turned on whilst auto memory entry

takes place, only RDS stations (i.e., stations with RDS capability)

are stored. RDS stations that have been preset for FM1 cannot

also be preset in FM2 or FM3.

• When the local seek function is turned whilst auto memory

entry takes place, stations with poor reception are not stored.

• When the Traffic Information function is on , only the local traffic

information station frequency will be stored.

Press the OK button.

Reception starts of the displayed station, and the seek mode

ends.

Cancelling mode during input:

Press the DNPP button.

The seek mode is cancelled.

Cancelling Auto Memory Entry During Its Operation:

Press the MENU button whilst auto memory entry is taking

place to stop the process.

Preset station seek with Programme service

name

(Function of Remote)

You can search for the preset station with Programme Service

name.

— 11 —

Tuner features

RDS features

DISP

Monaural Reception

When poor stereo reception is experienced, this function will

reduce noise and improve listening conditions.

44W

DISC

EJECT

DISP

NAME.S

OFF

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

T I

VOL ADJ

Press the ¢ button repeatedly until the monaural reception

function appears in the display.

LOUD

SCAN

B.S/RDM

REP

D.SCN

MTL/M.RDM

PROG/PTY

DISC

Press the 4 button to search in the other direction.

The function setting is indicated by "MONO OFF" or "MONO

ON" in the display, indicating that monaural reception is on or

off, respectively.

#1-6

38/ PTY

TI/VOL ADJ

MENU AM

Switching settings

KRC-PS1077R/977R

Press either the AM button or FM button.

The display and setting will change.

Band display

Press the MENU button to end the menu mode.

Kenwood intelligent Twin IF (K2I)

When the frequency of another station is too close to that of

the station currently being listened to, interfering with proper

reception, this function automatically narrows the range of

received frequencies to prevent such interference.

TI indicator

™ indicator

KRC-877R/877W/777R

Band display

TI indicator

™ indicator

— 12 —

RDS (Radio Data System)

AF (Alternative Frequency) Function

RDS is a digital information system that lets you receive signals

besides those of regular radio programmes, such as network

information being transmitted from radio stations.

When listening to an RDS station (ie, a station with RDS

capability), the programme service name of the station is

displayed along with the frequency, advising you quickly which

station is being received.

RDS (Radio Data System) stations also transmit frequency data

for the same station. When you are making long trips, this

function automatically switches to the particular frequency with

the best reception for the particular network of stations that

you want to listen to. The data is automatically stored,

allowing you to switch quickly to another RDS stations,

broadcasting the same programme, that has better reception.

These include stations stored in the station preset memory that

you often listen to.

When poor reception is experienced, automatically switch to

another frequency broadcasting the same programme in the

same RDS network with better reception.

The ™ indicator lights up when the AF function is turned

on.

Turning AF Function On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the AF function appears

in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "AF ON" or "AF OFF" in the

display, indicating that the AF function is on or off, respectively.

Switching settings

Press either the AM button or FM button.

The display and setting will change.

Press the MENU button to end the menu mode.

EON (Enhanced Other Network)

Displaying Frequencies:

Stations that offer EON also transmit information about other

RDS stations that have traffic information. When you are tuned

to a station that is not transmitting traffic information, but

another RDS station starts transmitting a traffic bulletin, the

tuner automatically switches to the other station for the

duration of the bulletin.

Hold down the DISP button for one second or more.

The frequency for the RDS station will be displayed for five

seconds instead of the station name.

NOTE

When no other stations with stronger reception are available for

the same programme in the RDS network, you may hear the

incoming broadcast in bits and snatches. Turn off the AF function

in such a case.

Alarm

When an emergency transmission (announcing disasters, etc.)

is sent, all current functions are interrupted to allow the

warning to be received.

— 13 —

RDS features

the preset volume.

Restricting RDS Region (Region Restrict Function)

If you are listening to a tape or disc when a traffic bulletin

begins, they will automatically be turned off. When the bulletin

ends or poor reception is experienced, the tape or disc will

begin playing again.

You can choose whether or not to restrict the RDS channels,

received with the AF function for a particular network, to a

specific region. When the Region Restrict Function is on, the

region is restricted.

Egnlish

NOTE

Turning Region Restrict Function On/Off:

Pressing the TI button whilst in the MW/LW band automatically

switches reception to the FM band. However, the MW/LW band

is not returned to when the TI button is pressed again.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Region restrict

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "REG ON" or "REG OFF" in

the display, indicating that the function is on or off,

respectively.

Switching to a Different Traffic Information Station:

Use the 4 / ¢ buttons to make an auto seek of the TI

stations in a certain band.

NOTE

• When you are listening to a tape or disc, you cannot change to

another TI station.

• When the auto TP seek function is turned on and reception

starts to weaken, the tuner automatically seeks traffic

information stations with better reception.

• If you are tuned to a station that is not a traffic information

station itself but which provides EON services, you can still have

traffic information received.

• Holding the TI button down for one second or more when the TI

function is on in the disc control mode results in a change to the

frequency display of the traffic information station for five

seconds.

Switching settings

Press either the AM button or FM button.

The display and setting will change.

Press the MENU button to end the menu mode.

NOTE

Sometimes stations in the same network broadcast different

programmes or use different programme service names.

Traffic Information Function

You can listen to traffic information. If you are listening to

tapes or discs, they will continue playing until a traffic bulletin

is broadcast.

Auto TP Seek Function

When the TI function is on and poor reception conditions are

experienced when listening to a traffic information station,

another traffic information station with better reception will be

searched for automatically. This function is on, when unit is

first powered on.

Turning TI function On/Off:

Press the TI button to turn the function on and off.

When the function is on, the TI indicator is turned on.

When none is being received, the TI indicator will blink on and

off. When a traffic information station is being received, the TI

indicator will turn on.

Turning Auto TP Seek Function On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Auto TP Seek

When a traffic bulletin begins to be broadcast, "TRAFFIC INFO !

/ TRAFFIC INFO" will be displayed, and reception will begin at

function appears in the display.

— 14 —

Press the 4 button to search in the other direction.

The function setting is indicated by "ATPS ON" or "ATPS OFF" in

the display, indicating that the function is on or off,

respectively.

Radio Text

You can display textual information being transmitted by RDS

stations.

Turning on Radio Text Display Mode:

Switching settings

Pressing the DISP button switches the display as follows.

Select the Radio Text Display mode.

Press either the AM button or FM button.

The display and setting will change.

If the traffic information station you are tuned to experiences

poor reception, this function automatically seeks another TP

station.

Programme Service name

Radio text

Press the MENU button to end the menu mode.

NOTE

If the RDS station currently tuned to is transmitting no text whilst

the Radio Text Display mode is turned on, "NO TEXT" will appear

in the display. Whilst awaiting reception, "WAITING" will be

displayed.

Presetting Volume for Traffic Information/News

Preset the volume level to be used for traffic information and

news broadcasts.

2WARNING

To prevent accidents, drivers should not look at the display whilst

on the road.

Tune into the station for which you want to set the volume.

Adjust the volume to the desired level.

Hold down the TI VOL ADJ button for two seconds or more.

The volume level blinks once in the display to indicate that the

data has been stored.

Future traffic information/news broadcasts are heard at the

preset level.

NOTE

• The volume cannot be lowered by this function during tuner

reception. The volume is only set when it is louder than the

listening volume of the tuner.

• You can arrange only to listen to traffic information or news

bulletins with at preset volume with the volume set at

minimum.

— 15 —

RDS features

Text Scroll

Programme Type (PTY) Function

Conduct auto seek tuning only on those stations with selected

kinds of programmes.

This function permits the text to be scrolled and the entire text

to be displayed. Switching between manual scrolling and

automatic scrolling is permitted. The factory default is manual

scrolling.

Egnlish

Press the 38(PTY) button.

“PTY” is displayed, and the Programme Type Selection (PTY)

Mode entered.

To scroll manually:

Press the DISP button to display the Radio Text.

If you make no key input in 30 seconds, the mode will

automatically turn off.

Holding down the DISP button for one second or more results

in one scrolling display of the text.

NOTE

You cannot use this function whilst the traffic information

function is turned on.

Manual/Automatic scroll switching:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

NOTE

Changing the Display Language to French, German, or Swedish

In the PTY mode, hold down the 38(PTY) button for one second

or more to display the name of the language currently used.

If you want to change the language, press the preset button for

the desired language and then the 38(PTY) button.

Press the ¢ button repeatedly until the Text scroll function

appears in the display.

Pressing the 4 button results in the functions being switched

in the reverse order.

English is #1, French is #2, German is #3, and Swedish is #4.

The text scroll function is displayed with "Scroll Auto" or "Scroll

Manu".

Select the type of programme to be received

• Press either the FM or AM buttons repeatedly until the type

of programme you want to listen to.

"Scroll Manu" (Manual scrolling)

"Scroll Auto" (Automatic scrolling)

The selection includes:

Switching settings

Press either the AM or FM button.

The display and setting will change.

Press the MENU button to end the menu mode.

To scroll automatically:

Press the DISP button to display the Radio Text.

The text will be displayed in one scrolling display.

Holding down the DISP button for one second or more results

in one scrolling display of the text.

NOTE

The setting of the text scroll function is in common with Text

Scroll for disc control.

— 16 —

• You can select the type of programme directly by pressing a

preset button. The buttons are factory-set to the following

type of programmes:

KRC-877R

Programme type

KRC-PS1077R/977R

/877W/777R

1.News

News

Affairs

Info

Sport

Educate

Drama

Culture

Science

Varied

1. Music

2. Speech

3. News

6. Varied

2.Current Affairs

3.Information

4.Sport

5.Education

6.Drama

7.Culture

8.Science

9.Varied

10.Pop Music

11.Rock Music

12.Easy Listening Music

13.Light Classical

14.Serious Classical

15.Other Music

16.Weather

Current Affairs

Information

Sport

Education

Drama

Cultures

Science

Varied Speech

Pop Music

Rock Music

Easy Listening

Light Classics M

Serious Classics

Other Music

Weather& Metr

Finance

4. Other Music

5. Serious Classical

NOTE

Changing the Preset Button Settings for Programme Type

After selecting the type of programme to be stored in a certain

preset button, press that button for at least two seconds.

The previously stored data for that button are erased and the new

programme type is stored.

Seeking the selected programme type

Press the 4 or ¢ button to make a seek of frequencies

with your selected type of programme.

Pop M

The display blinks and the seek starts.

Rock M

Easy M

Light M

Classics

Other M

Weather

Finance

Children

Social

Religion

Phone In

Travel

Leisure

Jazz

Country

Nation M

Oldies

Folk M

Document

Music

If your selected type of programme is found, the name of the

station is displayed and the station is tuned into.

"PTY" blinks in the display for about 30 seconds.

If you make no key input in 30 seconds, the PTY selection

mode will turn off automatically.

NOTE

17.Finance

If no programme can be found, "NO PTY" is displayed.

If you want to select another type of programme, repeat steps 2

and 3 above.

18.Children's programmes Children's Progs

19.Social Affairs

20.Religion

21.Phone

22.Travel

23.Leisure

24.Jazz Music

25.Country Music

26.National Music

27.Oldies Music

28.Folk Music

29.Documentary

Music

Social Affairs

Religion

Phone In

Travel & Touring

Leisure & Hobby

Jazz Music

Country Music

National Music

Oldies Music

Folk Music

Switching to Other Stations with the Same Type of Programme:

When "PTY" is blinking in the display, perform auto seek tuning.

The tuner scans for another station with the same type of

programme.

Cancelling Programme Type Function During Its Operation:

Press the 38(PTY) button.

Documentary

All Music

Speech

All Speech

Speech

(Speech.....1~9,16~23, 29, Music.....10~15, 24~28)

— 17 —

RDS features

NOTE

News Bulletin Function

with PTY News Timeout Setting

• This function is only available if the desired station sends PTY-

code for news bulletin or belongs to EON-Network sending PTY-

code for news bulletin.

• If you turn on the news bulletin function in the MW/LW band,

the band is switched automatically to the FM band.

However, the MW/LW band is not returned to when you turn off

the function.

You can arrange to have news bulletins interrupt your current

listening source, including other radio stations. When the News

Bulletin function is on, the PTY News Timeout setting allows

you to set the interval during which further news interruption

cannot take place. You can adjust the PTY news interruption

period from 10 to 90 minutes for each journey.

Egnlish

Turning News Bulletin Function On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the News Bulletin

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "NEWS ##MIN" or "NEWS

OFF" in the display, indicating that the function is on or off,

respectively.

NOTE

Depending on the interval chosen, the "##MIN" in the display will

change when the function is turned on.

Changing the Function Setting

Press either the FM or AM button.

Each time you press the FM or AM button until the desired

setting is displayed.

Press the FM button to increase the interval, and the AM

button to decrease it.

OFF ↔ 00MIN ↔ 10MIN ↔ 20MIN ↔ 30MIN ↔ 40MIN ↔ 50MIN

↔ 60MIN ↔ 70MIN ↔ 80MIN ↔ 90MIN

(MIN= minutes)

When you select the news interruption timeout interval, the

News function turns on and the NEWS indicator lights up.

When a news bulletin is received, "NEWS" will be displayed and

reception will begin at the preset volume.

NOTE

If you choose the "20MIN" setting, further news bulletins will not

be received for 20 minutes once the first news bulletin is

received.

Press the MENU button to end the menu mode.

— 18 —

Cassette player features

DISP

SRC

Playing Cassette Tapes

Loading and Playing Cassettes:

Press the ¡(EJECT) button to slide open the faceplate,

showing the cassette (insertion) slot. Holding the cassette with

the tape exposed to the right, insert it in the slot. The faceplate

will show the control panel, and the tape will start playing.

The ¢ indicator lights up when a cassette has been loaded.

44W

DISC

EJECT

DISP

OFF

NAME.S

T I

VOL ADJ

LOUD

SCAN

B.S/RDM

REP

D.SCN

MTL/M.RDM

PROG/PTY

DISC

Playing Cassettes Already Loaded:

Press the SRC button repeatedly until the tape mode is

obtained. "TAPE" is displayed when the tape mode has been

selected.

B NR/BC NR

38/PROG

MTL

B.S

REP

The tape will start playing.

KRC-PS1077R/977R

Listening to the other side:

Press the PROG button.

Tape side

Tape play switches to the other side.

Eject:

Press the ¡(EJECT) button to stop tape play. The faceplate

will slide to eject the tape.

Press the ¡(EJECT) button to show the control panel.

NOTE

• The sound will be temporarily muted whilst the faceplate is

moving.

• The only buttons that will work during the eject state are the

¡(EJECT), SRC, TI and ATT buttons, as well as the volume

control button.

MTL indicator BC NR indicator

Mode display

¢ indicator

• Remove a cassette from the unit when not listening to it for a

whilst. If you leave it in the unit too long, the tape may stick to

the tape head and cause the unit to malfunction.

KRC-877R/877W/777R

Tape side

Mode display

B NR indicator

¢ indicator

MTL indicator

— 19 —

Cassette player features

Fast Forwarding and Rewinding Cassette Tapes

Switching Tape Types

Select type of tape being played.

Fast Forwarding Tapes:

Press the FM button.

Switching Tape Types:

Egnlish

Press the MTL button to switch the MTL indicator on and off

and to select the tape type.

Rewinding Tapes:

Press the AM button.

Turn the MTL indicator off for normal tape (Type I) playback.

Turn the MTL indicator on for the following tape types:

CrO2 (Type II) FeCr (Type III) Metal (Type IV)

Selecting the wrong tape type may cause sound quality to

suffer.

Cancelling:

Press the PROG button.

Normal tape play returns.

Function of the KRC-PS1077R

Using Dolby B/C Noise Reduction

Listen to tapes recorded using the Dolby B or C NR system.

Using DPSS (Direct Programme Search System)

Skip forwards or backwards to other tracks during playback.

Turning Dolby NR On/Off:

Skipping to Beginning of Current Track or to Previous Tracks

(Rewind DPSS):

Press the BC NR button repeatedly to switch the Dolby NR

selection as follows.

Press the 4 button.

▼

Press once to rewind to the beginning of the current track,

twice to rewind to the beginning of the previous track, and so

forth.

You can skip up to 9 tracks this way.

Playback is continued after the tape is rewound by the

indicated number of tracks.

Dolby B NR ON

▼

Dolby C NR ON

▼

OFF

The B NR indicator lights up when Dolby B NR is turned on, and

the C NR indicator when Dolby C NR is turned on.

Skipping to Later Tracks (Fast Forward DPSS):

Press the ¢ button.

Press once to fast forward to the next one track, twice to fast

forward to the track after that, and so forth.

Up to 9 tracks can be skipped.

Playback is continued after the tape is fast forwarded by the

indicated number of tracks.

NOTE

Function of the KRC-977R/KRC-877R/KRC-877W/KRC-777R

Using Dolby B Noise Reduction

Listen to tapes recorded using the Dolby B NR system.

• During the first 5 seconds of each track, the previous track is

considered the "current" track (i.e., the "0" track). If you press the

4 button during that period, the tape rewinds to the beginning

of the previous track and not the one you are listening to.

Turning Dolby NR On/Off:

Press the B NR button to switch Dolby B NR on and off.

The B NR indicator lights up when Dolby B NR is turned on.

— 20 —

• The DPSS function "knows" where a track begins by detecting

the blank space preceding it (i.e., the space between tracks).

However, when the blank space lasts for less than 4 seconds or

contains noise, DPSS may not operate correctly. Furthermore,

quiet intervals within a song are detected as "blank spaces" if

they last for 4 seconds or more.

NOTE

The music repeat function "knows" where a track begins by

detecting the blank space preceding it (i.e., the space between

tracks). However, when the blank space lasts for less than 4

seconds or contains noise, this function may not operate

correctly. Furthermore, sections recorded at low levels may

trigger the function if they last for 4 seconds or more.

Cancelling DPSS During Its Operation:

Press the PROG button.

Blank Skip

Tape counter display

Automatically fast forwards to the beginning of the next track

when long blank spaces (10 seconds or more) are detected,

continuing tape playback. This function is on, when unit is first

powered on.

Switching the Tape display :

Press the DISP button to switch the tape counter display on

and off.

NOTE

Turning Blank Skip Function On/Off:

Press the B.S button to switch the blank skip function on and

off.

The tape counter is not exact, but only represents an

approximation of the elapsed time.

"Blank Skip ON/B.Skip ON" is displayed when the blank skip

function is turned on.

NOTE

• If the blank space contains hiss noise, the blank skip function

may not work correctly.

• Sections recorded at low levels may trigger the blank skip

function if they last for 10 seconds or more.

Music Repeat

Repeatedly plays the current track.

Turning Music Repeat Function On/Off:

Press the REP button to switch the music repeat function on

and off.

"Repeat ON" is displayed when music repeat is turned on.

Cancelling Music Repeat Function:

Press either the REP or PROG button.

— 21 —

External disc control features

■ When a unit equipped with an O-N switch is to be connected,

please also see the instruction manual of this unit.

Set the O-N switch to "N". "N"-operation will be set.

■ When a unit that is not equipped with an O-N switch, or the

changer switching unit "KCA-S200" is connected, "O"-

operation will be set.

DISP /

NAME.S

FM/

SRC DISC+

Egnlish

44W

DISC

OFF

EJECT

DISP

NAME.S

"N"-operation:

• The disc title and track title of the CD text can be displayed.

• The disc name will be displayed when the name has been

registered to any connected unit with the Presetting Disc

Names function, or when the playing unit contains a disc to

which the disc title has been recorded.

T I

VOL ADJ

LOUD

SCAN

B.S/RDM

REP

D.SCN

MTL/M.RDM

PROG/PTY

DISC

RDM

D.SCN

"O"-operation:

SCAN

REP

M.RDM

AM/DISC–

• CD text cannot be displayed.

• Regardless of the control unit, the characters that can be

registered with the Presetting Disc Names function are "A~Z

0~9 /, +, –, ∗, =, <, >, [ , ]".

KRC-PS1077R/977R

Disc number

Track time

Track number

• The disc name will be displayed when the name has been

registered to the playing unit with the Presetting Disc Names

function.

NOTE

The CD text, Presetting Disc Names, and Disc Name Preset Play

functions may not be operational depending on the unit.

Mode display

Playing Disc mode

This funciton permits the connection of optional players and

the playing of discs.

KRC-877R/877W/777R

Disc number

Track time

Track number

Playing Discs:

Press the SRC button repeatedly to select the external disc

control mode.

The disc will start playing.

NOTE

The external disc control mode will differ, depending on the unit

that is connected.

Mode Display Examples

Mode display

— 22 —

• "CD"...when a CD player is connected

• "DISC"...when a disc changer is connected

• "DISC-1", "DISC-2"...when two disc changers are connected

• Depending on the type of characters of the CD Text, some

characters may not be displayable.

Pausing and Restarting Disc Play:

Press the 38 button to make the disc pause.

Press the same button again to start play again.

NOTE

Fast Forwarding and Reversing Disc Play

Fast Forwarding Disc Play:

• When one disc has finished playing its last track, the next disc in

the changer starts playing. When the last disc in the changer

has finished, the player returns to the first disc and starts

playing it.

Hold down on the ¢ button.

Release your finger to play the disc at that point.

Reversing Disc Play:

Hold down on the 4 button.

• Disc #10 is displayed as "0". (KRC-877R/877W/777R only)

Release your finger to play the disc at the point.

NOTE

You cannot use reverse play between tracks depending on the

model being connected. Instead, the reverse play function is

cancelled when it reaches the beginning of a track, at which point

normal play automatically resumes.

Switching Display for Discs

Switch the display that appears whilst discs are playing.

Switching Display for Discs:

Each time you press the DISP button, the display during disc

play switches as follows.

Track time

Disc name (DNPS)

Disc title (Units featuring CD text/MD only)

Track title (Units featuring CD text/MD only)

NOTE

• You can give names to discs through the presetting disc name

function (see p. 26).

Note that depending on the unit, display may not be possible.

• If you try to display the name of a disc that does not have one,

"NO NAME" is displayed instead.

• When there is an attempt to display the title of a disc for which

the disc title/track title has not been recorded, "NO TEXT" is

displayed for CD and "NO NAME" is displayed for MD.

— 23 —

External disc control features

Play starts at the beginning of the displayed disc.

NOTE

Track Search

Search forwards or backwards through the tracks on the disc

until you reach the one that you want to listen to.

"LOAD" is displayed when discs are being exchanged on the disc

changer.

Egnlish

Making a Reverse Track Search:

Press the 4 button to display the desired track number.

Press once to search back to the beginning of the current track,

twice to search back to the beginning of the previous track, and

so forth.

Track / Disc Repeat

Repeat playing the current track or disc.

Play starts at the beginning of the displayed track number.

NOTE

Turning Repeat Play Function On/Off:

Press the REP button to switch the repeat play function on and

off as follows :

Pressing the 4 button whilst listening to track 1 only searches

back to the beginning of that track. The reverse search is not

"recycled" to the last track on the disc.

▼

Making a Forward Track Search:

Track Repeat ON

Press the ¢ button to display the desired track number.

Press once to fast forward to the next track, twice to fast

forward to the track after that, and so forth.

▼

Disc Repeat ON

▼

Track/Disc Repeat OFF

Play starts at the beginning of the displayed track number.

NOTE

"Track Repeat ON/T-Repeat ON" is displayed and the track

number blinks in the display when track repeat is on.

"Disc Repeat ON/D-Repeat ON" is displayed and the disc

number blinks in the display when disc repeat is on.

You cannot make a forward track search when listening to the last

track on a disc.

NOTE

The repeat play function is cancelled when you stop playing the

disc.

Disc Search

Search forwards or backwards through the discs in a disc

changer until you reach the one that you want to listen to.

Making a Reverse Disc Search:

Track Scan

Press the DISC– button to display the desired disc number.

Each time the button is pressed, the displayed disc number

decreases by one.

Successively play the beginning of each track on a disc until

you find the track that you want to listen to.

Play starts at the beginning of the displayed disc.

Starting the Track Scan :

Making a Forward Disc Search:

Press the SCAN button. "Track Scan ON/T-Scan ON" is

displayed and the first 10 seconds of each track are played, and

the tracks are played in order.

Press the DISC+ button to display the desired disc number.

Each time the button is pressed, the displayed disc number

increases by one.

The track number currently being heard blinks in the display.

— 24 —

Stopping to Listen to the Track Being Scanned:

Press the 38 or SCAN button again to stop the scan and keep

on listening to a track normally.

The display of the track number changes continuously as the

next track is being selected.

When the track has been selected, play starts.

The selected track number blinks in the display as it is being

played.

NOTE

• The track scan function is cancelled when you stop playing a

disc.

• The track scan function only scans each track on a disc once.

NOTE

When all the tracks on a certain disc have been played using the

random play function, the next disc on the changer starts playing

(with the random play function still turned on).

To change the track being heard, press the ¢ button.

Another track is selected and played.

Disc Scan

NOTE

Successively play the beginning of each disc on a changer until

you find the one that you want to listen to.

The random play function is cancelled when you stop playing a

disc.

Starting the disc scan:

Press the D.SCN button. "Disc Scan ON/D-Scan ON" is

displayed and the first 10 seconds of each disc are played, in

the order in which they are loaded on the changer.

The disc number currently being heard blinks in the display.

Stopping to Listen to the Disc Being Scanned:

Press the 38 or D.SCN button again to stop the scan and keep

on listening to the disc normally.

NOTE

• The disc scan function is cancelled when you stop playing a

disc.

• The disc scan function only scans each disc on the changer

once.

• "LOAD" is displayed when discs are being exchanged on the disc

changer.

Random Play

Play all the tracks on the current disc in random order.

Press the RDM button to switch the random play function on

and off.

"RDM ON" is displayed when random play is turned on.

— 25 —

External disc control features

entered.

Magazine Random Play

The cursor blinks in the position where character input can be

made.

Play the tracks on all the discs in the disc changer in random

order.

Press either the 4 or ¢ button to move the cursor to the

desired position.

Egnlish

Press the M.RDM button to switch the magazine random play

function on and off.

The 4 button moves the cursor to the left, and the ¢

"M-Random ON" is displayed when magazine random play is

turned on.

button to the right.

You can also move the cursor left or right by pressing the

^TRACK+ or TRACK– buttons, respectively, on the remote

control.

The display of the disc and track numbers change continuously

as the next track is being selected.

When the disc/track has been selected, play starts.

The selected disc/track number blinks in the display as it is

being played.

Each time the 38 button is pressed, the characters to be

entered change as listed below.

^{Press the DISC}+ or DISC– button to display the desired

NOTE

character.

Characters that can be displayed are as follows.

This function is not available with the following models:

KDC-C200/C300/C400/C301/C401

Alphabet (upper case): A ~ Z

To change the track being heard, press the ¢ button.

Another disc/track is selected and played.

Alphabet (lower case): a ~ z

NOTE

Numerals and symbols: 1~9 0 @ ” ‘ ` % & ∗ + - = , . / \ < > [ ]

• The magazine random play function is cancelled when you stop

playing a disc.

• The time needed for random selection depends on the number

of discs loaded in the disc magazine.

Special characters: á

›

NOTE

The operation and characters that can be entered may change

as listed below, depending on the unit that is connected.

A press of the 38 button exits the disc name preset mode.

Operations can be followed again from Step 2 at a time such

as this, and the characters to be input are selected using the

procedure described below.

Presetting Disc Names

Store the names of discs to be displayed when played.

Play the disc whose name you want to preset.

^{Press the DISC}+ or DISC– button to display the desired

character. Besides the alphabet (capital letters only) and

numbers, you can choose the following characters: /, +, –, *,

=, <, >, [ and ].

NOTE

• This function is not available for disc changers that do not

feature the Disc Name Preset function.

• This procedure is not to be used to store the disc and track titles

for MDs that you record.

Continue steps 3 and 4 until all the characters are chosen for

the name.

Hold down the NAME.S button for two seconds or more.

"NAME SET" is displayed and the disc name preset mode is

Press either the NAME.S button on the main unit or the OK

— 26 —

button on the remote control.

made by the unit that is playing.

The disc name is stored and the disc name preset mode is

cancelled.

• Discs in the disc changer that have never been played before

will appear as "NO ACCESS/NO ACCES" when the disc names

are displayed. When you cannot identify a disc because of the

"NO ACCESS/NO ACCES" display after inserting a disc

magazine, try playing it using the disc scan or a similar function

to display the disc name.

If you make no entry in a 10-second period, the name will be

stored with the characters input so far.

NOTE

• The number of characters and discs whose names can be

stored will differ depending on the disc changer that is

connected. Please see your disc changer manual for details.

• Discs are identified by their total length and number of tracks. If

another disc happens to have the same specifications as one

that you have already stored a name for, the name will be

displayed for it, too.

• If you want to change the name of a disc, repeat steps 1 and 2

to display the name, and then repeat steps 3 and 4 to input the

changes.

• Pressing the reset button does not erase the disc names stored

in a disc changer.

Also note that "NO DISC" will be displayed when a disc has not

been loaded.

Rapid display (forward / reverse):

Press the DISC+ or DISC– button.

Pressing the DISC+ button will rapidly display the preset

names/disc titles in order.

Pressing the DISC– button will rapidly display the preset

names/disc titles in reverse order.

When the name appears for the disc you want to play

Press the OK button.

The disc whose name is displayed will be recalled, and the disc

name preset play (DNPP) mode will end.

To cancel DNPP mode:

Press the DNPP button.

The disc name preset play (DNPP) mode will be cancelled.

Disc Name Preset Play (DNPP)

Function of remote control with DNPP button

If you have preset the name of a disc that you want to listen to

in the disc changer, you can look for it by name and start

playing it.

Press the DNPP button on the remote control.

"DNPP" will appear in the display, and the disc name preset play

mode is entered.

The preset names/disc titles of the disc in the disc changer to

which you are currently listening are successively displayed for

five seconds each.

In any of the units that are connected, discs that have not been

disc name preset will display "NO NAME".

NOTE

• This function can only be used in disc changers that were

manufactured or sold as of 1997. Also note that some units

cannot provide a display unless the disc name preset has been

— 27 —

External disc control features

NOTE

Text / Title Scroll

• Only units with a CD text feature permit title display.

• This function is not supported for MD changers.

This function permits the text to be scrolled and the entire text

to be displayed. Switching between manual scrolling and

automatic scrolling is permitted. The factory default is manual

scrolling.

Egnlish

To scroll manually:

Press the DISP button to display the disc title or the track title.

Holding down the DISP button for one second or more results

in one scrolling display of the titles.

Manual/Automatic scroll switching:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Text/title scroll

function appears in the display.

Pressing the 4 button results in the functions being switched

in the reverse order.

The text/title scroll function is displayed with "Scroll Auto" or

"Scroll Manu".

"Scroll Manu" (Manual scrolling)

"Scroll Auto" (Automatic scrolling)

Switching settings

Press either the AM or FM button.

The display and setting will change.

Press the MENU button to end the menu mode.

To scroll automatically:

Press the DISP button to display the disc title or the track title.

The titles will be displayed in one scrolling display.

NOTE

When the disc or track to be played changes, the title is displayed

in one scrolling display.

Holding down the DISP button for one second or more results

in one scrolling display of the titles.

— 28 —

Other features

Signal senser

Manual Open Switch Setting

By sliding the Manual Open Switch during forced closing, you

can open the control panel. Follow the directions below to

preset the number of times that this switch needs to be slid in

order to open the panel.

44W

DISC

EJECT

DISP

NAME.S

OFF

To preset the number of times to slide the Manual Open Switch:

T I

VOL ADJ

LOUD

SCAN

B.S/RDM

REP

D.SCN

MTL/M.RDM

Press the MENU button for at least one second.

"MENU" is displayed and the menu mode is turned on.

PROG/PTY

DISC

Press the ¢ button repeatedly until the Manual Open Switch

Setting function appears in the display. Press the 4 button to

search in the other direction.

The function setting is indicated by "OPEN SW #" in the display,

indicating that the Manual Open Switch Setting mode is on.

CLK

AUD/ AM/NF

KRC-PS1077R/977R

Switching settings

Press either the AM or FM button.

Press the FM button to change the setting number of times

higher, and press the AM button to change it lower. Settings

may be made from 1 to 3.

Press the MENU button to end the menu mode.

NOTE

The "#" display in the Manual Open Switch Setting mode will

differ depending on the setting. The initial setting value is "1".

£ indicator

Clock display

KRC-877R/877W/777R

£ indicator

Clock display

— 29 —

Other features

Audio Control Setting

Adjust various parameters of sound quality.

Adjustment mode

(Display;

Operation of Audio control button

KRC-PS1077R, 977R/

4 button

Bass decreased.

¢ button

KRC-877R, 877W, 777R)

Bass

Press the AUD button to enter the control mode.

Egnlish

Bass increased.

("Bass/Bas")

Press either the FM or AM button.

Treble

Treble decreased.

Left channel emphasized.

Rear channel increased.

Treble increased.

("Treble/Tre")

Balance

Each time the button is pressed, the adjustment mode will

change as follows:

Right channel emphasized.

("Balance/Bal")

Fader

Pressing the FM button advances the display, and pressing the

AM button reverses it.

Front channel increased.

("Fader/Fad")

Non-Fading

Preout Level

("NF pre Level/

NFLevel")

Non-fading sound

emphasized.

Front and rear

channels (including

preout) emphasized.

N-F Phase*^1,2

Bass

N-F Low-pass filter*^1,2

Rear High-pass filter*¹

Front High-pass filter*¹

Treble

High-pass filter

for front output

("HPF Front/

HPF F")

You can select the frequency to be cut, as

follows:

Through/Throu (through) ↔ 40Hz ↔ 60Hz ↔ 80Hz

↔ 100Hz ↔ 120Hz ↔ 150Hz ↔ 180Hz ↔

Balance

Fader

N-F Level*^1,2

KRC-777R:

KRC-PS1077R/977R/877R/877W:

None

High-pass filter

for rear output

("HPF Rear/

HPF R")

You can select the frequency to be cut, as

follows:

Not available during the Dual zone system on.

Only when Non-fading is switched on.

Through/Throu (through) ↔ 40Hz ↔ 60Hz ↔ 80Hz

↔ 100Hz ↔ 120Hz ↔ 150Hz ↔ 180Hz ↔

You can select the frequency to be cut, as

follows:

50Hz ↔ 80Hz ↔ 120Hz ↔

Through/Throu (through)

You can select the phase for non-fading output,

as follows:

Normal (0°) ↔ Reverse (180°)

Low-pass filter

for Non-fading

output

("LPF NF pre/

LPF NF")

Phase for Non-

fading output

("NF pre Phase/

NF Phase")

NOTE

Source tone memory

Each source (tape, FM, AM, and disc changer) has its own

memory in which to store the bass, treble and N-F level settings.

The settings made for a particular source are then recalled

automatically whenever you use that source (e.g., FM mode uses

the tone settings made for FM, AM for AM, etc.).

Press the 4/¢ button.

Look at the table to adjust the mode being displayed.

Press the AUD button to end the control mode.

NOTE

Setting the high-pass filter

You can separately set the high-pass filter for front and rear

output, including preouts. The high-pass filter works except

during non- fading preout when switching to non-fading.

The factory default settings for front output and rear output are

"through".

— 30 —

procedure in step 4.

Mask Key

Hold down the transmit button on the Mask key again until the

full transmit level indicator lights up in the display.

"APPROVED" will appear in the display, with the Mask key

function turning on.

If you have transmitted the Mask Key's signal once to the unit

in advance, you will have to transmit it once again if the unit

has been removed from the battery. This function helps prevent

theft.

If you press the RESET button or remove the battery:

The first time you turn the unit on again, “TRANSMIT 1” will

appear in the display, indicating the setting mode has been

entered. Repeat steps 4 and 5 above, and transmit the signal.

You can start operating the unit again when "APPROVED"

appears in the display.

When using the unit for the first time:

In order to deactivate the demonstration mode, be sure to

press the transmit button to transmit the Mask Key's signal.

If this procedure is not carried out, the control panel of the unit

will re-open in two seconds even with your vehicle's ignition

turned off.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the "Mask key" appears in

the display.

Press the 4 button to search in the other direction.

Hold down either the AM or FM button for two seconds or

more.

"TRANSMIT 1" will appear in the display, indicating the setting

mode has been entered.

Hold down the transmit button on the Mask key until the full

transmit level indicator lights up in the display.

"TRANSMIT 2" will be displayed.

Transmission part

Transmit button

NOTE

• Keep the Mask Key close to the signal sensor when you

transmit the Mask Key’s signal.

• If the Mask Key’s signal does not be received correctly, the

display will return to “TRANSMIT 1”. In this case, repeat the

— 31 —

Other features

Function of the KRC-PS1077R/KRC-977R

Switching Graphic Display

This function permits the graphic display to be switched to one

that is linked with the volume level value or to display various

modes. The initial setting is ON (displaying various modes).

Spectrum analyzer 1

Spectrum analyzer 2

Egnlish

Character

Turning the Graphic Display On/Off:

Track time (Only during disc play)

Track number (Only during disc play)

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Switching Graphic

Display function appears in the display.

Clock

Press the 4 button to search in the other direction.

The function setting is indicated by "Graphic ON" or "Graphic

OFF" in the display, indicating that the Graphic display is on or

off, respectively.

NOTE

The £ indicator lights whilst the clock is displayed.

"Graphic ON" (The graphic display works.)

"Graphic OFF" (The graphic display does not work.)

Function of the KRC-877R/KRC-877W/KRC-777R

Switching settings

Press either the AM button or FM button.

The display and setting will change.

Switching Display

You can change the display in each mode.

Press the MENU button to end the menu mode.

Changing the Display:

NOTE

Each time you press the CLK button, the display switches as

follows:

When making audio adjustments, even when this function is on,

the display will be linked to the audio adjustment value, not the

display of the various modes.

Mode display

Track time (Only during disc play)

Track number (Only during disc play)

Clock

Function of the KRC-PS1077R/KRC-977R

Switching Spectrum Analyzer Display

This function permits switching of the spectrum analyzer

display.

NOTE

Switching the Spectrum Analyzer Display:

Each time you press the CLK button, the display switches as

follows:

The £ indicator lights whilst the clock is displayed.

— 32 —

display, indicating that the Black mask is on or off, respectively.

"BLACK MASK ON/BLK MASK ON"

(The display will turn on by using only the

upper part of the display and the ATT

indicator.)

"BLACK MASK OFF/BLK MASK OFF"

(The display will turn on by using the

whole part of the display.)

Faceplate Angle Adjustment

You can adjust the faceplate angle for easy viewing.

Adjusting faceplate angle:

Press the ¡ (EJECT) button to make the faceplate slide open,

and then adjust the faceplate angle using the angle adjustment

switch.

Adjustment may be made from 0 to 2.

Switching settings

Press either the AM or FM button.

The display and setting will change.

Press the MENU button to end the menu mode.

0 1 2

NOTE

• Firmly slide the switch until it clicks.

• Do not apply excessive force to the faceplate under settings 1

or 2.

Black Mask

This function allows you to turn off the lower part of the

display if there is too much information in the display.

Turning the Black Mask On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Black Mask function

appears in the display.

Pressing the 4 button results in the functions being switched

in the reverse order.

The function setting is indicated by "BLACK MASK ON/BLK

MASK ON" or "BLACK MASK OFF/BLK MASK OFF" in the

— 33 —

Other features

Adjusting Time

Hold down either the AM or FM button for two seconds or

more to enter the Time Adjustment mode.

The time display will blink.

With automatic time adjustment, you can set the clock time

automatically according to time data sent from RDS stations

(after receiving RDS signals for several minutes). You can also

set the time manually if the automatic time adjustment function

is turned off. The factory default is automatic time adjustment.

Egnlish

• Adjusting the hours

Press the FM button to advance the hours, or press the AM

button to make the hours go back.

• Adjusting the minutes

Adjusting Time Automatically:

Press the ¢ button to advance the minutes, or press the

Tune into an RDS station for 3 or 4 minutes.

The time adjusts automatically to the correct local time.

4 button to make the minutes go back.

NOTE

Press the MENU button to end the menu mode.

The time is not adjusted when the RDS station you are tuned to is

not transmitting a time signal. Choose another RDS station in

such a case.

Turning Automatic Time Adjustment On/Off:

Dimmer

You can dim the display.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

NOTE

Press the ¢ button repeatedly until the Automatic Time

Adjustment function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "SYNC ON" or "SYNC OFF"

in the display, indicating that the Automatic Time Adjustment is

on or off, respectively.

The dimmer function is not available for units if the dimmer cable

is not connected.

Turning Dimmer On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

"SYNC ON" (Automatic time adjustment)

Press the ¢ button repeatedly until the Dimmer function

appears in the display.

"SYNC OFF" (Manual time adjustment)

Switching settings

Press the 4 button to search in the other direction.

The function setting is indicated by "Dimmer ON" or "Dimmer

OFF" in the display, indicated that the current dimmer setting is

on or off, respectively.

Press either the AM button or FM button.

The display and setting will change.

Press the MENU button to end the menu mode.

Adjusting Time Manually:

Switching settings

Press either the AM or FM button.

The display and setting will change.

Turn off the Automatic Time Adjustment as mentioned above.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the MENU button to end the menu mode.

Press the ¢ button repeatedly until the "Clock Adjst/Clock

Adjust" appears in the display.

Press the 4 button to search in the other direction.

— 34 —

Automatic Dimmer Function

The display dims when the car's lights are turned on.

Selectable Illumination

You can switch the colour of the button illumination between

green and amber.

NOTE

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

The dimmer function is not available for units if the dimmer cable

is not connected.

Press the ¢ button repeatedly until the Selectable

Illumination function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "Color Green" or "Color

Amber" in the display, indicating that the current colour is green

or amber, respectively.

TEL Mute

Shut down the audio system temporarily whenever an

incoming call is received.

NOTE

Switching settings

Press either the AM button or FM button.

The display and setting will change.

The function will not work if a cable is not connected to the car

phone.

Press the MENU button to end the menu mode.

When the telephone rings:

When a call is received, "CALL" is displayed and all the unit

functions are temporarily interrupted.

Restoring Original Unit Source During Phone Call:

Press the SRC button.

"CALL" disappears from the display, and the volume of the

original source is restored gradually.

Turning TEL Mute Function Off After Phone Call:

Hang the phone up.

"CALL" disappears from the display.

The original source (i.e., the one used before the phone call) is

returned to automatically, and the volume restored gradually.

Navigation Mute Function

When the KENWOOD Navigation System is connected, an

interruption of the audio guide results in the temporary

lowering of the audio level.

NOTE

The Navigation mute function cannot be used unless a TEL mute

cable is connected to the KENWOOD Navigation System.

— 35 —

Other features

"SWPRE Rear" (Rear preout)

Touch Sensor Tone

This function produces a beep sound that accompanies button

operation. It can be switched on or off.

"SWPRE N-Fad" (Non-fading preout)

Switching settings

Press either the AM or FM button.

The display and setting will change.

Egnlish

Turning the Beep On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the MENU button to end the menu mode.

NOTE

Press the ¢ button repeatedly until the Touch Sensor Tone

function appears in the display.

You cannot use the high-pass filter with non-fading preout.

Turning non-fading output On/Off :

Press the 4 button to search in the other direction.

The function setting is indicated by "Beep ON" or "Beep OFF" in

the display, indicating that the current beep setting is on or off,

respectively.

Hold down the NF button for one second or more to set the

function ON or OFF.

"NF ON" is displayed when the non-fading output is set ON.

Switching settings

Press either the AM or FM button.

The display and setting will change.

Contrast Adjustment

Press the MENU button to end the menu mode.

This adjustment permits easy viewing of the display.

NOTE

The beep sound is not output from the preout jacks.

To adjust the contrast:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Contrast Adjustment

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "Contrast ##" in the display,

indicating that the Contrast Adjustment mode is on.

Function of the KRC-PS1077R/KRC-977R/KRC-877R/KRC-877W

Switching preout

Switch the preout between the rear and non-fading. When you

switch to non-fading, you can adjust the volume separately.

The factory default is rear preout.

Switching settings

Press either the AM or FM button.

Press the FM button to change the setting values higher, and

press the AM button to change them lower. Settings may be

made from 0 to 10.

Switching the preout: (KRC-977R/877R/877W only)

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Switching preout

function appears in the display.

Press the MENU button to end the menu mode.

NOTE

Press the 4 button to search in the other direction.

The function setting is indicated by "SWPRE Rear" or "SWPRE

N-Fad" in the display, indicating that the current preout is rear or

non-fading, respectively.

The "##" display in the contrast adjustment mode will differ

depending on the setting. The initial setting value is "5".

— 36 —

Function of the KRC-PS1077R/KRC-977R/KRC-877R/KRC-877W

External Amp Control

Adjust the bass boost level of the external amplifier using the

main unit.

Dual Zone System

The following operation allows separate sound sources to

control the output of the front and rear speakers. The Dual zone

system can only be switched on or off when the source is set to

the AUX mode.

Switching the bass boost level:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Turning the Dual zone system On/Off:

Press the ¢ button repeatedly until the External amp control

function appears in the display.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the 4 button to search in the other direction.

The function setting is indicated by "AMP BASS Flat/FLT", "AMP

BASS +6", or "AMP BASS +12" in the display, indicating that the

external amplifier bass boost level is flat, +6dB, or +12dB,

respectively.

Press the ¢ button repeatedly until the Dual zone system

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "Zone 2 ON" or "Zone 2

OFF" in the display, indicating that the Dual zone system

function is on or off, respectively.

Switching settings

Press either the AM or FM button.

The display and setting will change.

Switching settings

Press either the AM or FM button.

The display and setting will change.

Press the MENU button to end the menu mode.

NOTE

Press the MENU button to end the menu mode.

As of December 1998, the power amplifiers controllable by the

main unit are as follows:

KAC-X501F/PS501F/X401M/PS401M/X301T/PS301T/X201T/PS201T

NOTE

• You must purchase the optional KCA-S210A/CA-C1AX/KDC-

CPS82/KDC-CX82 device before you can use this function.

• You can choose to send the AUX input through the rear channel,

and the unit’s tuner or tape source through the front channel.

• The Bass, Treble and Loudness adjustments do not affect the

rear channel.

• When the Dual zone system is turned on, the External disc

control features cannot be used.

• When you set the Dual zone system to on whilst the non-fading

preout is switched on, the sound of the non-fading preout does

not be outputted.

— 37 —

Basic Operations of steering remote control

Optional for the KRC-777R

2WARNING

To prevent accidents, do not attempt to use the steering remote

control whilst turning the steering wheel.

Egnlish

Loading and Replacing the Lithium Battery:

Use one lithium battery (CR2025).

ATT

FM/DISC +

Insert the battery with the + and – poles aligned properly,

following the illustration.

VOLUME

∞

FM/DISC+

AM/DISC–

SRC

ATT

SRC

DWN

AM/DISC –

2WARNING

Store unused lithium batteries out of the reach of children.

Contact a doctor immediately if the battery is accidentally

swallowed.

Basic operations

• SRC button

Each time you press the SRC button, the mode switches as

follows:

▼

Tuner mode

▼

Tape mode

▼

External disc control mode

▼

AUX mode

NOTE

• The mode switches to the next mode from any mode which

cannot be used.

• The external disc control mode will differ depending on the unit

that is connected.

— 38 —

• The AUX mode is available only when the changer / AUX

switching adapter (KCA-S210A or CA-C1AX) or CD changer

(KDC-CPS82 or KDC-CX82) is connected to this unit.

During the AUX mode, "AUX" will show in the display.

When the CA-C1AX is being used, the AUX Mode will replace

the External Disc Control Mode.

Press the AM/DISC– button to rewind the tape.

Press the FM/DISC+ button to fast forward the tape.

External disc control features

• VOLUME buttons

Press the 5 button to turn the volume up.

• DISC buttons

Press the ∞ button to turn the volume down.

• ATT button

Turns down the volume quickly. To return the volume to its

original level, press the button again. Turning down the volume

all the way also cancels attenuation.

Press the AM/DISC– button to search through the discs

backwards.

Press the FM/DISC+ button to search through the discs

forwards.

• TRACK buttons

Press the 4 button to search through the tracks backwards.

Press the ¢ button to search through the tracks forwards.

Tuner features

• TUNE buttons

Press the 4 button to make decreasing seeks (using the preset

tuning mode).

Press the ¢ button to make increasing seeks (using the preset

tuning mode).

• FM button

Selects and switches between the FM1, FM2 and FM3 bands.

• AM button

Selects the MW and LW bands.

Cassette player features

• 4/¢ buttons

Press the 4 button once for each track (including the current

track) you want to skip backwards.

Press the ¢ button once for each track you want to skip

forwards.

^{• AM/DISC}– / FM/DISC+ buttons

— 39 —

Accessories

9. Slide the Manual open switch for as many times as you have

preset in the Manual Open Switch Setting in the menu (see p.29)

to make the faceplate control panel appear.

External view

......... Number of items

.........1

Egnlish

2CAUTION

• If your car is not prepared for this special connection-system,

consult your KENWOOD dealer.

• Only use antenna conversion adapters (ISO-JASO) when the

antenna cord has an ISO plug.

.........1

• Make sure that all cable connections are securely made by

inserting jacks until they lock completely.

• If your vehicle's ignition does not have an ACC position, or if

the ignition cable is connected to a power source with constant

voltage such as a battery cable, the power will not be linked

with the ignition (i.e., it will not turn on and off along with the

ignition). If you want to link the unit's power with the ignition,

connect the ignition cable to a power source that can be turned

on and off with the ignition key.

5~8...KRC-PS1077 / 977R /

877R / 877W only

• If the fuse blows, first make sure that the cables have not

caused a short circuit, then replace the old fuse with one with

the same rating.

• Do not let unconnected cables or terminals touch metal on the

car or anything else conducting electricity. To prevent short

circuits, also do not remove the caps on the ends of the

unconnected cables or the terminals.

• Connect the speaker cables correctly to the terminals to which

they correspond. The unit may receive damage or fail to work if

you share the - cables and/or ground them to any metal part in

the car.

• After the unit is installed, check whether the brake lamps,

indicators, wipers, etc. on the car are working properly.

• Insulate unconnected cables with vinyl tape or other similar

material.

2CAUTION

The use of any accessories except for those provided might result

in damage to the unit. Make sure only to use the accessories

shipped with the unit, as shown above.

Installation Procedure

1. To prevent short circuits, remove the key from the ignition and

disconnect the -terminal of the battery.

2. Make the proper input and output cable connections for each unit.

3. Connect the cable on the wiring harness.

• Some disc changers need conversion cables for connection.

See the section on "Safety Precautions" for details.

• If the console has a lid, make sure to install the unit so that the

faceplate does not hit the lid when closing and opening.

4. Take Connector B on the wiring harness and connect it to the

speaker connector in your vehicle.

5. Take Connector A on the wiring harness and connect it to the

external power connector on your vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

8. Reconnect the - terminal of the battery.

— 40 —

Connecting Cables to Terminals

Antenna Conversion Adaptor (ISO–JASO) (Accessory3)

FM/AM antenna input

Antenna Cord (ISO)

Connector Function Guide

Rear left output (White)/

Pin Numbers for

ISO Connectors

Non-fading left output (White) (KRC-977R/877R/877W only)

Cable Colour

Functions

Rear right output (Red)/

External Power

Connector

Non-fading right output (Red) (KRC-977R/877R/877W only)

Non-fading right output (Red) (KRC-PS1077R only)

A–4

A–5

A–6

A–7

A–8

Yellow

Blue/White

Orange/White Dimmer

Red

Battery

Power Control

Non-fading left output (White) (KRC-PS1077R only)

Display Data Output Jack (KRC-877R only)

Outputs data representing the unit's current state,

causing it to appear in the external display.

To connect to this jack, a converting adapter (optional) is

necessary.

Ignition (ACC)

Earth (Ground)

Connection

Black

Speaker

Connector

Wiring harness

Fuse

(10A)

KENWOOD disc changer/DAB control input

(Accessory1)

B–1

B–2

B–3

B–4

B–5

B–6

B–7

B–8

Purple

Purple/Black

Gray

Gray/Black

White

White/Black

Green

Rear Right (+)

Rear Right (–)

Front Right (+)

Front Right (–)

Front Left (+)

Front Left (–)

Rear Left (+)

Rear Left (–)

NOTE

To connect the Disc changer or DAB unit,

consult each manual.

If no connections are made,

do not cut the tube off from

the edge of the cable.

Front left output

(White)

To "EXT.AMP.CONT." terminal of the amplifier

having the external amp control function.

Front right output

(Red)

EXT.AMP CONT

Green/Black

External amplifier control cable

(Pink / Black)

Connect to the terminal that is grounded when

either the telephone rings or during conversation.

Battery cable (Yellow)

TEL MUTE

NOTE

TEL mute cable (Brown)

Ignition cable (Red)

To connect the KENWOOD navigation

system, consult your navigation manual.

Connect either to the power control terminal

when using the optional power amplifier, or to

the antenna control terminal in the vehicle.

P.CONT.OUT

A–7 Pin (Red)

ANT.

CONT.

A–4 Pin (Yellow)

Power control/ Motor antenna

control cable (Blue/White)

Connector A

Connector B

— 41 —

Connecting Cables to Terminals

Installtion

■

2WARNING

Installation

Connecting the ISO Connector (see p.41)

The pin arrangement for the ISO connectors depends on the type

of vehicle you drive. Make sure to make the proper connections to

prevent damage to the unit.

Firewall or metal support

The default connection for the wiring harness is described in 1

below. If the ISO connector pins are set as described in 2 or 3,

make the connection as illustrated.

Screw (M4X8)

(commercially

available)

Egnlish

1 (Default setting) The A-7 pin (red) of the vehicle's ISO

connector is linked with the ignition, and the A-4 pin (yellow) is

connected to the constant power supply.

Unit

Vehicle

Ignition cable (Red)

A–7 Pin (Red)

Bend the tabs of the

mounting sleeve with

a screwdriver or

Battery cable (Yellow)

A–4 Pin (Yellow)

Self-tapping

screw

(commercially

available)

similar utensil and

attach it in place.

Metal mounting

strap

(commercially

available)

2 The A-7 pin (red) of the vehicle's ISO connector is connected to

the constant power supply, and the A-4 pin (yellow) is linked to

the ignition.

NOTE

Unit

Vehicle

Make sure that the unit is installed securely in place. If the unit is

unstable, it may malfunction (eg, the sound may skip).

Ignition cable (Red)

A–7 Pin (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

3 The A-7 pin (red) of the vehicle's ISO connector is not

connected to anything, whilst the A-4 pin (yellow) is connected

to the constant power supply (or both the A-7 (red) and A-4

(yellow) pins are connected to the constant power supply).

Unit

Vehicle

Connect to a power source that can be

turned on and off with the ignition key.

Ignition cable (Red)

2CAUTION

To attach this unit, make sure the front of the control panel faces you

and fit it into the mounting sleeve by pressing the four corners of the

hard rubber frame at the same time.

Battery cable (Yellow)

A–4 Pin (Yellow)

Do not apply strong pressure to other sections than the corners;

otherwise troubles such as the impossibility of opening or closing the

panel may result.

— 42 —

Removing the Unit

■

Removing the Unit

■

Removing the hard rubber frame

Insert the removal tool into the indentations in the hard rubber

frame, and pull it gently until the lock is released.

Make the faceplate control panel appear.

NOTE

When the control panel of the faceplate is hidden, the unit

will be locked by the sleeve, making it more difficult to

remove the unit.

Refer to the section “Removing the hard rubber frame” and

then remove the hard rubber frame.

Remove the screw (M4×8) on the back panel.

Insert the removal tool deeply, as illustrated, with the L on the

left and the R on the right.

Screw (M4X8)

(commercially

available)

Accessory4

Removal tool

Accessory2

Removal tool

Push upward the both

tools, as shown, and pull

the unit toward you until it

is halfway out. The unit

may drop if you pull it out

completely.

Pull the unit all the way out

with your hands, being

careful not to drop it.

— 43 —

Attaching Steering Remote Control (Optional for

the KRC-777R)

Mounting Example

Egnlish

Attach the operation section and the light emitting section of the

Steering Remote Control as shown above.

Be sure to attach them to positions that can ensure proper

operation.

2CAUTION

• Clean dirt and oil from the positions where the Steering Remote

Control sections are to be attached.

• If the attached position is cold, warm it before attaching.

• The position should be selected so that the product does not

come in the way of steering operation.

• Do not attach anything on the surface of a steering wheel

incorporating an air bag.

• Before finally affixing the transmitter, check various angles to

find an orientation that provides faithful operation.

— 44 —

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before

calling service, first check the following table for possible problems.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not turn on.

The fuse has blown.

After checking for short circuits in the cables, replace the

fuse with one having the same rating.

No ACC position on vehicle ignition.

The Attenuator function is turned on.

Connect the same cable to the ignition as the battery cable.

Turn off the Attenuator function.

No sound can be heard, or the

volume is low.

The fader and/or balance settings are set all the way to

one side.

Reset the fader and/or balance settings.

The input/output cables or wiring harness are connected

incorrectly.

Reconnect the input/output cables and/or the wiring harness

correctly. See the section on "Connecting Cables to

Terminals".

The cassette tape is bad.

Try playing another cassette tape. If no problem is

experienced, the first tape was bad.

The tape does not go in. /

No sound can be heard even

though the tape display is

made.

The car ignition was turned off during tape eject; or the

tape was pulled out during loading, switching the mode to

tape mode even though no tape is in.

Press the Eject button.

Nothing happens when the

buttons are pressed.

The computer chip in the unit is not functioning normally.

The tape head is dirty.

Press the reset button on the unit (see page 4).

Clean the tape head, referring to the section on "Cleaning

the tape head" (see page 4).

The sound quality is poor or

distorted.

A speaker cable may be pinched by a screw in the car.

The speakers are not wired correctly.

Check the speaker wiring.

Reconnect the speaker cables so that each output terminal

is connected to a different speaker.

Radio reception is poor.

The car antenna is not extended.

Pull out the antenna all the way.

The antenna control cable is not connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The faceplate does not open or

close.

The ambient temperature is too low.

Warm up your car.

— 45 —

Troubleshooting Guide

PROBLEM

POSSIBLE CAUSE

SOLUTION

The memory is erased when

the ignition is turned off.

The battery cable has not been connected to the proper

terminal.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The ignition and battery cable are incorrectly connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

Egnlish

The TEL mute function does

not work.

The TEL mute cable is not connected properly.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The TEL mute function turns on

even though the TEL mute

cable is not connected.

The TEL mute cable is touching a metal part of the car.

Pull the TEL mute cable away from the metal part of the car.

External disc control mode

PROBLEM

POSSIBLE CAUSE

SOLUTION

The disc control mode cannot

be selected.

No cable has been connected to the disc changer input

terminal on the unit.

Connect the cable to the disc changer input terminal on the

unit.

The specified disc does not

play, but another one plays

instead.

The specified CD is very dirty.

Clean the CD.

The CD is upside-down.

Load the CD with the labelled side up.

The disc is loaded in a different slot from that specified.

Eject the disc magazine and check the number for the

specified disc.

The disc is severely scratched.

Something is touching the disc changer.

The CD is scratched or dirty.

Try another disc instead.

The sound skips.

Remove whatever is touching it.

If skipping happens at the same place when the car is

stopped, something is wrong with the CD. Clean the CD.

The display shows that the

changer is being played, but no

sound can be heard.

The computer chip in the unit is not functioning normally.

Random play or magazine random play has been selected.

Press the reset button on the unit (see page 4).

The specified track does not

play.

Turn off the random play or magazine random play function.

If the following situations, consult your nearest service centre:

• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display during the Changer Mode.

• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is entered when switching modes.

— 46 —

The following messages are displayed when certain problems are occurring in your system. Take the recommended

actions.

No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.

EJECT

] Load the disc magazine properly.

No CD in the unit.

] Insert the CD.

No disc has been loaded in the disc magazine.

NO DISC

E-04

] Load a disc into the disc magazine.

No disc has been loaded in the disc magazine.

] Load a disc into the disc magazine.

The CD is very dirty. The CD is upside-down. The CD is scratched a lot.

] Clean the CD and load it correctly.

Nothing has been recorded on the MD.

BLANK

NO TRACK

NO PANEL

E-77

] The next MD is automatically played back

No tracks are recorded on the MD, although it has a title.

] The next MD is automatically played back.

The faceplate of the slave unit being connected to this unit has been removed.

] Replace it.

The unit is malfunctioning for some reason.

] Press the reset button on the unit. If the "E- 77", code does not disappear, consult your nearest service centre.

Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.

] Check the disc magazine. And then, press the reset button on the unit.

If the "E- 99" code does not disappear, consult your nearest service center.

E-99

The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F), stopping

HOLD

all operation.

] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the

disc starts playing again.

If this indicator continues blinking, it is possible that the tape has become jammed or tangled.

] Contact the Kenwood dealer if the tape cassette cannot be ejected.

— 47 —

Specifications

Specifications subject to change without notice.

FM tuner section

Audio section

Frequency Range (50 kHz Space).......................87.5 - 108.0 MHz

Usable Sensitivity (S/N: 26dB)....................................0.7 µV/75 Ω

Quieting Sensitivity (S/N: 46dB) .................................1.6 µV/75 Ω

Frequency Response ( 3.0dB).................................30 Hz-15 kHz

Signal to Noise ratio .............................................65 dB (MONO)

Selectivity (DIN)..............................................≥ 80 dB ( 400 kHz)

Stereo Separation .....................................................35 dB (1kHz)

Preout Level(mV)/Load

(KRC-PS1077R/977R; with CD changer)...............4 V/10 kΩ

(KRC-877R/877W/777R)..............................1800 mV/10 kΩ

Preout Impedance

(KRC-PS1077R/977R)...................................................80 Ω

(KRC-877R/877W/777R)..........................................≤ 600 Ω

Maximum output power .................................................44 W x 4

Full Bandwidth Power (DIN45324,+B=14.4 V) ................28 W x 4

Tone action

Egnlish

MW tuner section

Frequency Range (9 kHz space) ............................531 - 1611 kHz

Usable Sensitivity (S/N: 20dB) .............................................25 µV

Bass ............................................................100 Hz 10 dB

Treble ..........................................................10 kHz 10 dB

LW tuner section

General

Frequency Range ...............................................153 kHz-281 kHz

Usable Sensitivity (S/N: 20dB) .............................................45 µV

Operating voltage (11 - 16V allowable)................................14.4 V

Current Consumption ............................................................10 A

Installation Size (W x H x D) ...........................182 x 53 x 161 mm

Weight...............................................................................1700 g

Cassette player section

Tape Speed ..............................................................4.76 cm/sec.

Wow & Flutter.....................................................0.08 % (WRMS)

Frequency response ( 3 dB) ......................30 Hz - 20 kHz (70 µV)

Separation ...............................................................43 dB (1 kHz)

Signal to Noise ratio

Dolby C NR ON (KRC-PS1077R only) .........................73 dB

Dolby B NR OFF.........................................................65 dB

Dolby NR OFF............................................................57 dB

— 48 —

Memorex MC7101 User Manual
Lucent Technologies Cell Phone Accessories 20 User Manual
Lindy KVM EXTENDER 39357 User Manual
Kenwood KDC MP5043U User Manual
Kenwood DP 4090 User Manual
Jura Capresso F50 User Manual
Hitachi Travelstar Z7K320 User Manual
Electrolux E24CM75GSSA User Manual
Dell PowerVault LTO4 120 User Manual
Clarion CDC655TZ CDC655Tz User Manual