INSTRUCTION MANUAL
CD-ROM DRIVE
MODEL CDR-8130
IMPORTANT
- Read all of these instructions carefully and understand
them before using your CD-ROM drive.
- Keep this instruction manual for future reference.
- If this CD-ROM drive changes ownership, be sure this
manual accompanies the CD-ROM drive.
CONTENTS
IMPORTANT SAFEGUARD--------------------------------------- 4
CONTROLS AND FUNCTIONS---------------------------------- 6
INSTALLATION ------------------------------------------------------ 7
DRIVE OPERATION ------------------------------------------------ 8
EMERGENCY EJECT PROCEDURE -------------------------- 9
LENS CLEANING---------------------------------------------------10
TROUBLESHOOTING---------------------------------------------10
MECHANICAL DIMENSIONS -----------------------------------11
SPECIFICATIONS--------------------------------------------------12
READ AND KEEP THIS MANUAL
1
CAUTION
INVISIBLE LASER RADIATION WHEN OPEN. DO NOT
STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS.
VORSICHT
ATTENTION
ADVARSEL
UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG
GEÖFFNET. NICHT IN DEN STRAHL BLICKEN AUCH NICHT
MIT OPTISCHEN INSTRUMENTEN.
RADIATION DU FAISCEAU LASÉR INVISIBLE EN CAS
D'OUVERTURE EVITER TOUTE EXPOSITION AUX
RAYONS.
USYNLIG LASERSTRÅLING VED ÅBNING, NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNCTION. SE
IKKE IND I STRÅLEN - HELLER IKKE MED OPTISKE
INSTRUMENTER.
ADVARSEL
VARNING
USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG
SIKKERHEDSLÅS BRYTES. STIRR IKKE INN I STRÅLEN
ELLER SE DIREKTE MED OPTISKE INSTRUMENTER.
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. STIRRA EJ IN I
STRÅLEN OCH BETRAKTA EJ STRÅLEN GENOM OPTISKT
INSTRUMENT.
VARO !
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET
ALTTIINA NÄKYMÄTTÖMÄLLE LASER-SÄTEILYLLE. ÄLÄ
TUIJOTA SÄTEESEEN ÄLÄKÄ KATSO SITÄ OPTISEN
LAITTEEN LÄPI.
For Europe
Caution - Use of controls or adjustments or peformance of procedures other than
those specified herein may resultin hazardous radiation exposure.
DEFINITIONS AND A SYMBOL
The following symbol and signal word are used throughout this instruction
manual with the following definitions.
This symbol indicates any condition or particle, which if not
strictly observed, could result in damage or destruction of the
equipment.
IMPORTANT
Important notes indicate a subject of common errors
in operation or maintenance.
3
IMPORTANT SAFEGUARDS
SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR EQUIPMENT
READ ALL INSTRUCTIONS.
SAVE THESE INSTRUCTIONS FOR LATER USE.
FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE PRODUCT.
PRECAUTIONS FOR SAFETY
Power source
-This CD-ROM Drive should be operated from the type of power source
indicated on the marked label. (+12V DC / +5V DC)
To avoid the risk of electric short circuits or damage to your CD-ROM drive
- Do not expose your CD-ROM Drive to rain or moisture.
- Do not open or remove the cover of your CD-ROM Drive.
It may cause personal injury by rapid rotating disc.
- Turn off your SYSTEM and unplug the power supply cable of your SYSTEM
from the wall outlet before installing your CD-ROM Drive, interface card or
connecting cables.
- Do not allow liquids and foreign objects to get in .
- Do not place heavy loads on the CD-ROM Drive.
- Do not use this CD-ROM Drive without mounting it.
- Firmly attach the DC power supply cable, connecting cables between the
CD-ROM Drive and other devices and keep them connected securely.
In case of failure
In case of the following conditions, turn off the SYSTEM including the CD-ROM
Drive and unplug the power supply cable of the SYSTEM from the wall outlet
immediately.
Do not attempt to service the CD-ROM Drive yourself and refer servicing to
qualified service personnel immediately.
- If objects of any kind have been entered into your CD-ROM Drive
- If liquid has been spilled into your CD-ROM Drive
- If your CD-ROM Drive has been exposed to rain or water
- If your CD-ROM Drive does not operate normally when the operating
instructions are followed
- If your CD-ROM Drive has been dropped or your CD-ROM Drive has been
damaged
- If your CD-ROM Drive exhibits a distinct change in performance
PRECAUTIONS FOR USE
Installation conditions
Do not install your CD-ROM Drive under the following conditions. It may lead to
trouble or affect performance by dust on the pick-up lens and the disc, by heat or
vibration.
4
- In a place where an operation temperature reaches beyond the specified
temperature 40C
- High humidity locations
- In a location subject to extreme changes of temperature and humidity
- In a room where dust density higher than 0.1 mg/m3
- In a room that has air conditioning with humidity control which may scatter
calcium combinations and other powdered substances
- In a room containing exhaust gas fumes such as exhaust gas from gasoline or
diesel engines or corrosive gas such as H2S (Hydrogen sulfide)
- In a location subject to vibration and jarring during drive operation
- In a location subject to sudden shock and jolt during drive operation
Mounting requirements
Mount your CD-ROM drive tightly in horizontal or vertical position by screws.
The inclination of your CD-ROM Drive should be within 5° as shown below. If you
do not,
- When the Disc Tray is opened, the disc may jump out and may be damaged.
- It may cause damage to your CD-ROM drive.
- Your CD-ROM Drive may not work with full performance.
5
5
5
5
Mounting screw
The screws must be ISO (M3 x 0.5) to mount the CD-ROM Drive tightly and
avoid damaging the mechanism inside the CD-ROM Drive. (See page 11)
Moving your CD-ROM Drive
Remove the disc and close the Disc Tray before moving the CD-ROM Drive. If
your CD-ROM Drive is moved with the disc loaded or the Disc Tray opened,
both the disc and the CD-ROM Drive may be damaged.
PRECAUTIONS FOR CARE
Cleaning of the CD-ROM Drive, discs
- Never clean your CD-ROM Drive and discs with silicon cloths or cloths soaked
in water, solvents (thinner, benzine), abrasive cleaner, anti-static sprays, any
record cleaner sprays, liquid cleaner or aerosol cleaner. It may damage or
discolor the coating of the CD-ROM Drive or damage or deform discs.
- Clean your CD-ROM Drive including the Disc Tray and discs with a clean, dry,
soft cloth at least once a month.
- Clean your CD-ROM drive's pick-up lens using a cleaning disc.
5
CONTROLS AND FUNCTIONS
Front Panel
Rear Panel
(6)
(2)
39
1
2
40
(10)
(8)
(9)
(3)
(7)
(4) (1)
(5)
(1) LOADING/UNLOADING/BUSY Indicator
Indicator blinks green only when the Disc Tray is being opened or
closed, or when the CD-ROM drive is accessing data.
(2) Disc Tray
When the power of the CD-ROM Drive is turned off, the Disc Tray can
not be opened and closed.
(3) Headphone Jack (3.5 mm)
(4) Headphone Volume Control
Adjust the headphone volume.
(5) OPEN/CLOSE Button
Press this button to open or close the Disc Tray.
(6) Manual Emergency Eject Hole
Only in case of emergency:
If the Disc Tray does not open when the OPEN/CLOSE Button is
pressed, the CD-ROM Drive's Manual Emergency Eject mechanism may
be activated.
This should be used only in case of emergency.
See Page 9 about Manual Emergency Eject Procedure.
(7) Audio Output Terminal
Lch
GND
Rch
(8) Device Configuration Jumper
This Connector is used to set operation modes such as Master,
Slave and CSEL
6
6 4 2
Device is
Master
(Default setting)
OR
Circuit Board
Device is
Slave
3 1
5
Cable
Select
(9) ATAPI Interface Connector
ATAPI bus connection (40 pin)
(10) Power Supply Connector (DC Input)
For connecting the power supply cable.
4 3 2 1
Circuit Board
+12V
GND
+5V
INSTALLATION
WHAT YOU NEED
HARDWARE
- CD-ROM Drive
- Interface card
- Interface cable
- Mounting screws
- Power supply cable
HARDWARE OPTION
- Audio connecting cable
SOFTWARE
- Sound Card
- CD-ROM device driver
NOTE
If you need a interface card or interface cable or CD-ROM device
driver, contact your dealer.
HARDWARE INSTALLATION
To install this CD-ROM drive in the host computer, refer to the instruction
manual of each host computer.
And to install the interface card in the host computer, refer to the instruction
manual of each host computer and each interface card.
7
Install the CD-ROM Drive following general installation procedure shown below.
1. Check the Device Configuration Jumper settings of the CD-ROM Drive such
as Master, Slave, CSEL. (See page 6)
2. Turn off the host computer and unplug the power supply cable of the host
computer.
3. Remove the host computer cover.
4. Install the CD-ROM Drive into the host computer and mount tightly by screws.
5. Check the settings of the interface card.
6. Install the interface card in the slot.
7. Firmly attach the interface cable from the interface card to the CD-ROM
Drive.
8. Firmly attach Audio connecting cable as required.
9. Finally attach a spare DC power supply cable from the computer power supply
to the CD-ROM Drive firmly.
10. Install the host computer cover.
Power supply cable
Interface cable
Audio connecting cable
SOFTWARE INSTALLATION
To install CD-ROM device driver in the host computer to operate this CD-ROM
Drive, refer to the instruction manual of each CD-ROM device driver.
DRIVE OPERATION
1. Turn on the SYSTEM including the CD-ROM Drive.
2. Press the OPEN/CLOSE button of the CD-ROM Drive to open the Disc Tray.
3. Place the disc in the center of the Disc Tray with label side up as shown
below.
4. To close the Disc Tray, press the OPEN/CLOSE button on the CD-ROM Drive
or push lightly the center of the front of the Disc Tray as shown below. The
disc Tray will close the rest of the way automatically.
5. Operate referring to the instruction manual of CD-ROM device driver.
8
120 mm Disc
Disc label side
80 mm Disc
Disc label side
Disc Tray
Disc Tray
Push
Push
IMPORTANT
- Do not press the OPEN/CLOSE button while the host computer is accessing
the disc. It may caused an error.
- When not using the CD-ROM Drive, keep the Disc Tray closed. It will prevent
the entry of the dust and dirt, and reduce the requirements for disc and lens
cleaning
CAUTION
If you do not observe the following items, troubles, such as that the Disc Tray can
not be opened or can not be closed, may occur or it may cause damage to the
mechanism of the CD-ROM Drive.
- Never use a damaged, broken or deformed disc.
- Do not press down hard on the Disc Tray when opening and closing the Disc
Tray.
EMERGENCY EJECT PROCEDURE
Only in case of emergency:
If the Disc Tray does not open when the OPEN/CLOSE Button is pressed, make
sure that the power of the CD-ROM Drive is turned on and software lock function
has not been used. If the Disc Tray still will not open, the CD-ROM Drive’s
Manual Emergency Eject mechanism may be activated.
This should be used only in case of emergency.
REMOVAL PROCEDURE
1. Turn off the CD-ROM Drive and wait at least 15 seconds till the disc stops
rotating.
2. Insert the Eject bar (for example, a straightened paper clip) into the Manual
Emergency Eject Hole about 25 mm (1 inch).
3. Pull the Disc Tray
9
CAUTION
Do not use a breakable bar.
A broken bar inside the CD-ROM
Drive may cause a malfunction.
Eject bar
Push
Minimum straight length = 30 mm
Diameter = 1 - 1.8 mm
Lens Cleaning
A commercially available "Laser Lens Cleaning Disc" may be used to clean up the
pick-up lens of the CD-ROM Drive.
Use the Compact Disc Laser Lens Cleaner LLC-1. (by AUDIO SOURCE in U.S.A.,
by AKUSTIK SISTEME VERTRIEBS GHBH in GERMANY and by SAEC
COMMERCE CO.,LTD. in JAPAN.)
(1) Turn on the CD-ROM Drive.
(2) Using the small brush supplied with the cleaning disc case, straighten up
the disc cleaning brushes on the back of the cleaning disc.
(3) Place the cleaning disc in the Disc Tray with its arrow marked on the disc at
front.
(4) Press the OPEN/CLOSE button or push the center of the Disc Tray lightly
and close the Disc Tray.
(5) In about 20 seconds, the pick-up lens is cleaned by the cleaning disc.
(6) Press the OPEN/CLOSE button and remove the cleaning disc.
(7) Set the cleaning disc in its case with the disc cleaning brushes in the pad
hole.
(8) Restart the SYSTEM.
TROUBLESHOOTING
- If your CD-ROM Drive does not operate properly, check the following table.
- You may have to check the other devices included in your SYSTEM.
- If you can not locate the cause, turn off the power of the SYSTEM including the
CD-ROM Drive and unplug the power supply cable of the SYSTEM from the
wall outlet immediately and contact your dealer.
- When calling for service, provide the following information :
1. Model name
2. Detailed symptoms
10
Symptoms
The CD-ROM
Drive does not
operate even when 2. The disc is dirty.
a disc is loaded.
Possible causes
1.You place the disc up-side 1.Place the disc right side up in the
down in the Disc Tray.
Remedy
Disc Tray, then load it.
2.Clean the disc surface.(See page 4)
3.Clean up the pick-up lens.(See page
10)
3. The pick-up lens is
dirty.
4.Change the disc.
4.The disc is scratched or
warped.
5.Cable connection is
incorrect.
5.Turn off your SYSTEM and re-
connect cables correctly.
The Disc Tray can
not beopened.
The program is incorrect. It Check the program. Check the
is locked by the program.
program.
Communications
between the host
computer and the
devices on the
There are devices with the
same Device Configuration Configuration Jumper setting.
jumper setting on the
Give each device a different Device
interface cable.
interface cable can
not be done.
MECHANICAL DIMENSIONS
(A) Hole
5 (max) Surface of
130.0
the CD-ROM DRIVE
149.3
Mounting Screw
M3X0.5
12-M3
(Depth
: Max. 5)
(A : Hole)
Mounting frame of
the host computer
(A)
(A)
(A)
(A)
(A)(A)
(A)(A)
10+/- 0.5
0Å0
218Å}0.5
21.8+/- 0.5
139.8+/- 0.5
146
41.3
Dimensions (unit : mm)
11
SPECIFICATIONS
GENERAL
Power Requirements DC Voltage +12V
±10%
±5%
1.0A
0.7A
+5V
Ripple
Dimensions ( W x H x D )
+12V
+5V
300 mVpp (maximum)
150 mVpp (maximum)
146 x 41.3 x 190 mm (Excluding front panel)
Front panel : 149.3 x 42.7 x 5 mm
0.95 kg
Mass
Operating & Storage Conditions
Temperature
5 - 45 °C
-30 - 60 °C
15 - 85% RH
(operating)
(non-operating)
(operating)
Relative humidity
(non-condensing)
(non-operating)
(non-condensing)
10 - 90% RH
PERFORMANCE
Disc Diameter
120 mm, 80 mm
Rotational speed
71.3 - 52.7 s-1 (Approx. 4,200 - 3,200 rpm)
650 Mbytes (Mode 1)
Capacity (1M=220=1,048,576)
742 Mbytes (Mode 2)
Conditions : 333,000 blocks (74 min.) for
recorded area
Single side
Record Side
Sustained Data Transfer Rate
(1k=210=1,024)
Access Time
1,200 - 2,400 kbytes/s
(Mode 1)
Average (1 / 3 - Stroke)
Full Stroke
90 ms
(Typical) (Note 1)
150 ms (Typical) (Note 2)
Notes :
1) Average of 100 access operations, between 15-min 00-s 00-block and 35-min
00-s 00-block, with latency.
2) Average of 100 access operations, between 00-min 02-s 00-block and 59-min
59-s 74-block, with latency.
AUDIO PERFORMANCE
Number of Channels
Output Level
2
Line : 0.7 Vrms TYP. (47 kohms load)
Headphone : 0.6 Vrms TYP. (32 ohms load)
Line : 4-pin terminal (2.54 mm pitch)
Headphone out : ø3.5 mm Jack
Output Terminal
RELIABILITY
Data Error Rate
10-12 or less
10-9 or less
(Mode 1)*
(Mode 2)*
* Raw error rate assumed to be 10-3 or less.
INTERFACE
ATAPI - BUS
40-pin non-shielded connector
Note
Design and specifications are subject to change without prior notice.
Hitachi has done everything possible to prevent the failure of the CDR-8130. However, it is not
absolutely free from failure. In case it should fail, Hitachi is not responsible for the results.
12
13
|