T E C H N O L O G I E S
User Guide
CipherUSB FDE
(CAUF1W, CAUF1W-2, CAUF1M, CAUF1M-2,
CAUF2W, CAUF2W-2, CAUF2M, CAUF2M-2)
Technical Support
If you need any assistance to get your unit functioning properly, please
have your product information ready and contact Addonics Technical
Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Initial Setup
This procedure only needs to be done when setting up the CipherUSB
for the first time, or when a new password is desired. The CipherUSB will
retain the last password it was programmed with and models without
Two-Factor Authentication do not require any driver or software to work.
1. Connect the CipherUSB to a computer running Windows, and connect
a USB storage device into the CipherUSB. The CipherUSB will not
respond until a working storage device is connected to its USB device
port.
2. For models without Two-Factor Authentication, insert the CipherUSB
password utility disc. If an Autorun menu appears, select "Run
CipherUSB.exe" or browse to your CD drive using Windows Explorer
and launch the CipherUSB program. If you are setting up the
CipherUSB for the first time, the following dialog box should appear:
3. Click OK to proceed to the utility. Choose a password as short or as
long (up to 32 characters) as desired, and enter it into the “Setup” and
“Confirm” fields. Then click Start.
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
CAUTION: KEEP YOUR PASSWORD SAFE AND REMEMBER IT.
OTHER CipherUSB DEVICES CAN USE THE SAME PASSWORD TO
UNLOCK MEDIA ENCRYPTED BY THIS DEVICE. IF THE PASSWORD
IS LOST THE DATA IS LOST. THERE IS NO “BACK DOOR” TO
UNLOCK OR RECOVER THE PASSWORD OR THE ENCRYPTION
KEY.
After confirming once more for security, the CipherUSB will be
programmed with a 256-bit encryption key seeded by the password.
Once the CipherUSB has been programmed, a dialog will appear
instructing you to remove the device and reinsert it, then the program will
close automatically. After removing and reinserting the CipherUSB it will
be properly initialized.
Using the CipherUSB With Storage
Data that is encrypted will only be readable after being decrypted again
using a CipherUSB programmed with the correct password.
While it is required to connect the CipherUSB with a storage device
attached in order to encrypt files, it is not necessary to encrypt files on
the attached storage. Files may be encrypted or decrypted on any of the
computer's storage devices.
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
Using the CipherUSB FLE To Encrypt Files
Once The CipherUSB FLE has been initialized with a password (and has been
unlocked if the Two-Factor feature is included), the software will present the
File/Folder Encryption screen, similar to this:
On the left side of the window is a Tree view of the computer's storage
devices. Clicking on any of these will show their contents on the right side.
To encrypt files, select one or more items on the right side, then drag them to
the closed padlock icon in the upper-left corner of the window. To decrypt files,
select one or more encrypted files on the right side, then drag them to the
open padlock icon in the upper-left corner of the window.
Alternatively, right-clicking on any selected item will bring up the context menu
as shown:
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
The File Encrypt and Decrypt selections in the Replace the Originals
section work the same as dragging to the padlock icons.
Choosing File Encrypt in the Create a new Folder section will cause a new
folder to appear called AES_Encrypted, containing the encrypted version of
the files. Choosing File Decrypt in the Create a new Folder section will
cause a new folder to appear called AES_Decrypt, containing the
decrypted version of the files.
Performing encryption on a folder or drive will operate on all of the files in
that folder or drive. Note: the encryption and decryption functions do not
traverse through subfolders. Only the actual files in the selected folder or
drive will be encrypted. Files located in subfolders will not be affected.
Write Protect
Write protection only works with storage devices that are removable media,
such as USB Flash Drives or flash media in a standard reader. Write
protection will not work with Fixed disk media, such as USB hard drives or
SSD drives, the Addonics Pocket eSATA/USB DigiDrive, or eSATA hard
disks connected through adapters such as the Addonics USB 3.0 to
eSATAp Adapter or the Addonics USB 3.0 to eSATA Mini Adapter.
Write Protection works by blocking requests from the computer to write to
the media and does not protect the media from being written to if the media
is not connected to the CipherUSB device. It only works with the drive
connected through the CipherUSB.
There are two types of Write Protection available:
Write Protect Boot Record/MBR
Checking this box will cause the CipherUSB to refuse any write requests
from the computer to the first logical sector of the removable media. This
feature provides basic protection against malware attacks that attempt to
deploy payload at boot time or upon insertion of removable media.
Write Protect Entire Storage
Checking this box will cause the CipherUSB to refuse ALL write requests
from the computer to the removable media. This feature will protect all data
on the media from being erased or overwritten while in use with the
CipherUSB device.
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
Updated Firmware
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
1. Read the firmware update for important changes to the unit's operation
or the update procedure. If a firmware release note contradicts these
instructions, follow the release notes instead.
2. Insert the CipherUSB with a storage device. The CipherUSB will not
respond unless a storage device is attached to it. 3. Run the
CipherUSB.exe program. If the CipherUSB unit has not been
initialized with a password, the Update Firmware tab will not appear.
Initialize the unit with a password, unplug it, plug it back in, then select
the Update Firmware tab.
4. Be sure the DX Information section shows AES Length is 256 and
ECB mode is selected for the CAUF1W, CAUF1W-2, CAUF1M-2 or
CAUF1M. CBC mode for the CAUF2W, CAUF2W-2, CAUF2M,
CAUF2M-2.
5. In the Update new firmware section, click the Firmware button.
Change the file type to “BinaryFile(*.256) if neces sary, then browse to
the folder containing the new firmware and open it.
6. Click the Start Programming button. A dialog will shortly appear
instructing you to remove the CipherUSB and reinsert it. After
removing and reinserting the device, the firm ware update will be
completed.
NOTE: The CipherUSB may or may not need to be initialized with the password
again. If a storage device using the existing password is connected when the
CipherUSB is reinserted and the file system appears intact, the password has been
retained. Otherwise it may be necessary to set the password again.
CONTACT US
Phone:
Fax:
408-573-8580
408-573-8588
Email:
|