5. When the Status indicators illuminate, the UPB80 is charging. Continue
charging the UPB80 until all indicators illuminate and then extinguish.
Safety Precautions
Charging and Connecting the UPB80
Please read the following warnings carefully before using the UPB80
Universal Notebook Battery. Use the product correctly and according to
the procedures described in this manual.
Prior to use, completely charge the UPB80. Follow the instructions for
setting the output voltage on the UPB80. Provided with the UPB80 is a
plastic bag with an assortment of plug and jack tips. Plug and jack tips are
each marked with a letter designator which corresponds to notebook
models listed in the “Compatibility Guide” and “Compatibility” section of
this manual. Plug tips are used to connect the output power of the UPB80
to the input DC voltage port on the notebook. Jack tips are used to connect
the UPB80 to a power source (notebook’s AC/DC Power Adapter, or
APC’s TravelPower or Universal Power Adapters - purchased separately).
Tips are marked with an uppercase letter (A, B, C, etc.). Jacks are marked
6. Check the UPB80 capacity. Press the On/Status push button. The Status
indicators on the UPB80 will light and stay lit for about 5 seconds. If this is
the first time using the battery, and all indicators do not light, fully charge the
UPB80 before continuing.
®
WARNINGS
• Do not attempt to disassemble or alter any part of this product.
www.apc.com
7. The UPB80 is now ready for use. If the notebook power adapter, APC
TravelPower Adapter, or APC Universal Power Adapter is present, the
UPB80 will pass through power to the notebook. If the notebook power
adapter is removed, the UPB80 will continue to provide power to the
notebook, and the notebook will appear to be connected to utility power. To
optimize runtime for the battery, adjust the notebook power settings to save
power. See notebook user manual for information on changing power mode
settings.
o
• Do not store outside of the following temperature range: -4 to 140 F
o
(-20 to 60 C). Do not operate outside of the following range: 32-
o
o
104 F (0 to 40 C), as this will damage or reduce the life of the
battery.
• Do not allow this product to have contact with water or other liquids.
If water or other liquids enter the battery interior, immediately
unplug the product from the notebook. Continued use of the product
may result in fire or an electrical shock.
Universal Notebook
Battery (UPB80)
5
• Do not place this product near a heat source or expose the battery to
direct flame or heat, as the battery may explode.
Turning On the UPB80
When the battery has been stored for more than 15 minutes, or has not been
attached to a notebook), the battery will enter Sleep Mode. To turn the battery on,
press the On/Status push button for 1 second, then release. The Status indicators
illuminate, showing the battery is awake.
User’s Manual
Prior to Use
Before using the UPB80 it should be fully charged. Please follow the
instructions below on how to use and maintain the UPB80.
6
Checking UPB80 Status
1
Finding the Notebook Voltage
You can check the status of the battery at any time. Simply press and hold the On/
Status push button for 1 second, then release. The LED Status indicators will
illuminate, indicating the charge level of the battery. Refer to Figure 3 for Status
Indicator Definitions (when you turn on or check status of the battery, it will show
the remaining charge level capacity).
Setting
Before using this battery, determine the DC input voltage requirement for
the notebook being used. Notebook voltage ratings are usually indicated
in one of two locations: at the back of the notebook on the system label or
on the notebook AC-to-DC power adapter label.
Introduction
Thank you for purchasing APC’s Universal Notebook Battery (model
UPB80). Please read the entire user manual prior to use. Fill out and mail
the enclosed Warranty Registration Card, or register this purchase online
If the voltage cannot be located, refer to the “Compatibility Guide” to
determine the required setting for the notebook being used.
APC’s Universal Notebook Battery is a slim and lightweight external
battery pack which provides up to 8-hours of continuous runtime (actual
runtimes may vary by notebook model and power setting).
2
Output Voltage Setting
Please refer to Figure 1 to become familiar with all aspects of the UPB80.
To set the voltage output for the UPB80, proceed as follows:
Features
1. Locate the input voltage requirement for your notebook computer.
(Refer to “Finding the Notebook Voltage Setting” for instructions).
• Ultra-lightweight construction reduces bulk and weight in notebook
carry-on luggage.
• Wide range of selectable output voltages power most notebook
computers.
2. Remove the yellow sticker on the UPB80 which covers the Output
Voltage Selector Switch.
• Four charge/discharge level indicators.
• Letter-coded power tips provided compatibility with most notebook
computers (see Compatibility Guide).
3. Turn the Output Voltage Selector Switch to the required voltage
setting for the notebook being used.
• Compatible with APC’s TravelPower Adapter and Universal Power
Adapter models.
• 80 Watts of continuous power, up to 100 Watts peak power output.
• Up to 8 hours of continuous runtime for your notebook.
4. Press the "On/Status" button to make the change effective. Note: If
this is the first time using the battery, attach a power source to wake
up the battery. Continue reading the manual for further instructions
on first use.
3
Changing the Voltage While the Battery is
Inspection
in Use
Check the package contents for the following items:
If the voltage selector dial is moved while the battery is in use, the battery
will interrupt the output of power to your notebook computer. To resume
power output, ensure that the voltage selector is turned to the correct
output voltage (please refer to the Notebook Users Manual for
instructions). Press the On/Status push button for approximately 1 second,
then release. The On/Status indicators will illuminate, indicating the
• APC Universal Notebook Battery (UPB80)
• Input/Output UPB80 Power Cable
• Conversion Plug and Jack Package
• Compatibility Guide
• User’s Manual
• Warranty Card
battery has resumed power output.
• Voltage and Tip Label
• Rubber “Feet” (4)
If any item listed above is not in the package, contact APC Customer
Service.
Figure 1. Universal Notebook Battery (UPB80) User Interface
|