Midland Radio Portable Radio MO 1008 User Manual

User’s Guide

Olympian™ Series

MO-1008 Eight Channel VHF-FM Mobile Transceiver

MO-4008 Eight Channel UHF-FM Mobile Transceiver

MO-1016 Sixteen Channel VHF-FM Mobile Transceiver

MO-4016 Sixteen Channel UHF-FM Mobile Transceiver

MO-1008 / 4008 / 1016 / 4016 User’s Guide

FCC RF EXPOSURE COMPLIANCE REQUIREMENTS FOR

OCCUPATIONAL USE ONLY

The FCC has adopted a safety standard for human exposure to RF energy. Proper

operation of this radio under normal conditions results in user exposure to RF energy

below the Occupational Safety and Health Act and Federal Communication

Commission limits.

Mandatory Safety Instructions to Installers and Users:

This radio is NOT approved for use by the general population in an uncontrolled

environment. This radio is restricted to occupational use and work related operations

only. Radio operators must have the knowledge to control their exposure conditions

and the exposure conditions of bystanders and/or passengers to satisfy the lower

exposure limit allowed for General Population.

To comply with FCC RF exposure limits, DO NOT operate the transmitter of this mobile

radio when a person outside the vehicle is within 36 inches (92 centimeters) of the

antenna.

The antenna supplied by the manufacturer or radio dealer must be mounted at a

location such that during radio transmission, no person or persons can come closer

than the above indicated minimum safe distance to the antenna, i.e. 36 inches. To

comply with current FCC RF exposure limits, the antenna must be installed at or

exceeding the minimum safe distance stated above, and in accordance with the

requirements of the antenna manufacturer or supplier.

Vehicle Installation Instructions:

The antenna used for this transmitter must be mounted on the center of the roof ONLY

and must be installed in vehicle having the following characteristics in order to prevent

bystanders and passengers from being exposed to levels exceeding the limits for

General Population/Uncontrolled Exposure environment:

All passengers must be sitting under a solid metal roof.

Rooftop width must be at least 72 inches (183 centimeters) OR the edges of the

physical boundary of the vehicle must be at least 72 inches apart.

DO NOT operate the radio without the proper antenna installed. Do not substitute any

antenna for the one supplied or recommended by the manufacturer or radio dealer. The

antenna gain must not exceed 0 dBd. By not following the antenna recommendations

you may be exposing person(s) to excess radio frequency radiation. You may contact

your radio dealer or the manufacturer for further instructions.

DO NOT transmit more than 50% of total radio use time (50% duty cycle). Transmitting

for more than 50% of the time can cause FCC RF exposure compliance requirements

to be exceeded. This radio is transmitting whenever the TX/Busy indicator is red or the

7 icon is displayed. Pressing the PTT switch on the side of the microphone normally

causes the radio to transmit.

ꢀ

The preceding information is provided to make you aware of RF exposure and

how to ensure that this radio is operated within FCC RF exposure limits.

You, as the qualified end-user of this radio device must control the exposure conditions

of bystanders to ensure the minimum separation distance, stated above for satisfying

FCC RF exposure compliance, is maintained between the antenna and nearby

persons. Transmit only when all person(s) are at least the minimum distance from the

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Contents

Conventions and Symbols in this Book ................................... 5

Disclaimer ................................................................................ 4

Safety....................................................................................... 4

Introduction .............................................................................. 6

Radio Features..................................................................... 7

Radio Controls ......................................................................... 9

Front Panel........................................................................... 9

Rear Panel ......................................................................... 10

Backlit LCD Details............................................................. 10

Setup...................................................................................... 11

Unpacking .......................................................................... 11

Installation .......................................................................... 11

Basic Operation ..................................................................... 12

Turning the Radio On and Off............................................ 12

Channel Selection .............................................................. 12

Receiving Transmissions from Other Radios..................... 12

Transmitting to Other Radios ............................................. 14

Scanning Channels ............................................................ 15

Programmable Functions....................................................... 18

Message Display Quick Reference........................................ 20

Specifications......................................................................... 23

MO-Series Connectors .......................................................... 24

Warranty Statement............................................................... 25

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Conventions and Symbols in this Book

This symbol marks a “caution”. Cautions are special

notices which you should read and follow carefully to

avoid possible damage to your equipment and to avoid

potential danger to yourself or other people.

This symbol marks an “important point”. Important points

are specific instructions which should be followed closely

for proper operation.

ꢀ This symbol marks a “note”. Notes are hints or tips which

offer additional information to help you.

Disclaimer

Midland Radio Corporation is committed to continuous quality

improvements, for this reason specifications may change without

prior notice.

Every effort has been made to ensure that the information in this

document is complete, accurate, and up-to-date. Midland

assumes no responsibility for the results of errors beyond its

control. The manufacturer of this equipment also cannot

guarantee that changes in the equipment made by unauthorized

people will not affect the transceiver’s performance or functions.

Safety

Your MO-1008 / 4008 / 1016 / 4016 mobile transceiver has been

carefully designed to give you years of safe, reliable

performance. As with all electrical equipment, however, there are

a few basic precautions you should take to avoid injury to

yourself or damage to the radio:

Read the instructions in this book carefully. Be sure

to save it for future reference.

Read and follow all warning and instruction labels on

the radio itself.

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Be sure the PTT button is not pressed when you do

not need to transmit.

Do not operate the radio near unshielded electrical

blasting caps or in an explosive atmosphere.

Do not operate the transmitter of any radio unless all

RF connectors are secure.

All equipment must be properly grounded for safe

operation.

Do not allow children to operate or play with the radio

equipment.

Never attempt to disassemble or service the radio

yourself. All equipment should be serviced by a qualified

technician. Contact you local dealer or communications

coordinator for assistance.

It is mandatory that radio installations in vehicles

fueled by liquefied petroleum gas conform to the

NFPA 58 standard. National Fire Protection Association

Standard, NFPA 58, applies to radio installations in

vehicles fueled by liquefied petroleum (LP) gas with the

LP gas container in the trunk or other sealed-off space

within the interior of the vehicle. This standard requires

that:

1. Any space containing radio equipment shall be

isolated by a seal from the space in which the LP

gas container and its fittings are located.

2. Remote (outside) filling connections shall be vented

to the outside.

Do not allow the antenna to touch or come in very

close proximity with the eyes, face, or any exposed

body parts while the radio is transmitting.

ꢀ The above warning list is not intended to include all

hazards that may be encountered when using this radio.

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Introduction

Congratulations! By choosing the Midland Olympian™ Series

MO-1008 / MO-4008 / MO-1016 / MO-4016 mobile transceiver,

you have selected a professional grade radio. Its rugged design

will provide years of reliable service and its sophisticated

software allows many customizable options.

Radio Features

Your Olympian Series mobile transceiver is a fully

programmable, synthesized radio featuring:

58 or 16 channel capacity.

545 Watts (UHF)/50 Watts (VHF) transmit power. 5 Watt

low power selection available.

512.5 KHz and 25 KHz channel spacing programmable

per channel.

56 fully programmable buttons. The function of each

button is assigned by dealer programming.

5Noise squelch level software programmable per channel.

The channel squelch level may also be adjusted using a

programmable button.

5Flexible scan programming allows for two priority

channels to be assigned. Priority scan, priority transmit

and priority lookback are programmable. Scan talkback

and nuisance delete are available.

550 CTCSS tones and 104 DCS codes are programmable

per channel. In addition, up to three custom CTCSS tone

frequencies may be programmed into the radio.

5A 2-tone decode sequence may be programmed for each

channel. Up to 10 sequences are programmable per

radio. Each sequence includes setup for individual and

group calls.

MO-1008 / 4008 / 1016 / 4016 User’s Guide

5A 2-tone call function may be programmed for each

channel. One of the 10 available 2-tone sequences may

be sent with a programmable button press.

5A busy channel lockout feature is programmable per

channel. An override function is available to allow

transmission during repeater hangtime.

5A transmit time-out timer may be programmed to limit

continuous transmission time. A PTT release and penalty

timer are also programmable.

5A public address mode allows the radio and microphone

to be used as a public address system when connected

to an external public address speaker.

5A talk-around function button may be programmed to

allow for repeater talk-around without using an additional

channel.

5A programmable emergency mode may be activated by a

programmable function button or external foot-switch.

5An external horn output is available to notify you of a call

when you’re away from the vehicle.

5A password function is available to prevent unauthorized

radio operation. When programmed, a four keypress

sequence must be entered each time the radio is turned

on, in order to operate the radio.

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Radio Controls

Front Panel

1. Power/volume knob. Rotate clockwise to turn on the radio.

Rotate further clockwise to increase volume.

2. TX/Busy indicator. Lights green when channel is busy and

red when radio is transmitting.

3. Backlit LCD display. Provides radio status and channel

information.

4. [∼]/[ ] buttons. Programmable function buttons, normally

used for channel selection.

5. Internal front speaker.

6. Microphone jack.

7. [A]-[D] buttons. Programmable function buttons, dealer

customized to provide the features and convenience you

require.

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Rear Panel

1. SO-239 antenna connector.

2. 13.6 V DC power connector (negative ground only).

3. 3.5 mm mono audio jack for external speaker connection.

4. High density DB15 option interface connector.

Backlit LCD Details

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Setup

Unpacking

The following items are supplied in the standard package:

5One transceiver (MO-1008, MO-4008, MO-1016 or MO-

4016).

5One microphone.

5One mounting bracket.

5One mounting hardware package.

5One user’s manual.

Installation

Radio installation should only be done by qualified and trained

personnel, familiar with automotive electronics installation, and

FCC RF exposure guidelines. This transceiver should be

installed in 12V negative ground vehicles only. More complete

installation instructions are available in the corresponding radio

service manual.

Antenna selection, installation and positioning requires

knowledge of RF radiation and exposure conditions and should

be performed by qualified personnel only. Please consult your

dealer or communications coordinator for more information.

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Basic Operation

! Before turning on your radio for the first time, you should

ensure power connections have been made correctly and

all antenna connections are proper and secure.

Turning the Radio On and Off

Rotate the power/volume knob clockwise past the detent to turn

on the radio. Rotate the power/volume knob further clockwise to

increase the volume. Rotate the power/volume knob

counterclockwise past the detent to turn off the radio.

If “PP” is displayed after turning on the radio, you must enter the

programmed password (4 keypress sequence) to use the radio.

Consult your dealer or communications coordinator if you have

further questions.

Channel Selection

Use the up and down keys to select the desired operating

channel. Please consult your dealer or communications

coordinator regarding channels programmed in your radio.

Press and hold the up and down keys to quickly scroll through

the available channels.

Receiving Transmissions from Other Radios

Each channel of your radio may be programmed for carrier

squelch operation, CTCSS/DCS operation or 2-tone operation.

The following paragraphs describe these modes of operation.

Ask your dealer or communications coordinator if you have

questions on how your radio has been programmed to operate.

Carrier Squelch Operation

A signal that matches the programmed receive frequency will be

heard if it is of sufficient strength to exceed the squelch

threshold. An on frequency signal exceeding the squelch

MO-1008 / 4008 / 1016 / 4016 User’s Guide

threshold level will be indicated by a steady green Tx/Busy

indicator.

CTCSS/DCS Operation

CTCSS or DCS signaling adds an additional condition to carrier

squelch operation. In addition to the signal having to exceed the

squelch threshold level, the received signal must also have the

correct CTCSS or DCS tone or code before the audio will be

passed to the speaker. CTCSS or DCS signaling allows multiple

users on the same frequency to hear only signals which have

their correct CTCSS tone or DCS code. An on frequency signal

with the correct CTCSS or DCS signaling will be indicated by a

steady green Tx/Busy indicator. An amber Tx/Busy indicator

means that the channel is busy, but the correct CTCSS or DCS

signaling is not present.

ꢀ CTCSS/DCS allows multiple users to share the same

frequency. However CTCSS/DCS is only useful to avoid

disturbing other users with messages not related to them.

If more than one radio is transmitting at the same time,

this will cause interference. Do not transmit if the Tx/Busy

indicator is illuminated green or amber. Wait until the

channel is clear before transmitting.

2-tone Operation

2-tone signaling allows individual or group calls to be made to

your radio. The radio may have been programmed to mute all

receive signals until a 2-tone signal has been decoded. When

the programmed 2-tone signal is decoded, the Tx/Busy indicator

will blink green, a beep sequence may sound, and subsequent

receive audio will be heard over the speaker. The radio may be

programmed to mute the speaker again after a programmed

time, or you may press and hold the programmed Call Reset

function button to mute the radio until it receives a new call.

MO-1008 / 4008 / 1016 / 4016 User’s Guide

ꢀ Consult your dealer or communications coordinator for

further details on how your radio has been programmed

for 2-tone operation.

ꢀ 2-tone signaling allows users to receive only calls

intended for them. However, more than one radio

transmitting at a time will still cause interference. Do not

transmit if the Tx/Busy indicator is illuminated green or

amber. Wait until the channel is clear before transmitting.

Transmitting to Other Radios

! Before transmitting, the FCC requires you monitor

the channel to make sure it is clear. Transmitting

while someone else is transmitting will create

interference and disrupt both conversations.

Follow these steps to transmit to other radios.

1. Monitor the channel by pressing the programmed function

button. Depending on programming the monitor button may

disable 2-tone, CTCSS, DCS or noise squelch to allow you

to check for channel activity. Channel activity is also

indicated by the Tx/Busy indicator.

2. If the channel is clear, press and hold the push to talk (PTT)

switch on the side of the microphone.

3. The Tx/Busy indicator will glow red while the radio is

transmitting.

4. Hold the microphone approximately 2 inches from your

mouth and speak across the face of the microphone in a

clear, normal voice.

5. Keep the PTT switch pressed until you have finished

speaking.

6. Release the PTT switch to return to receive mode.

ꢀ Do not shout! It will only create distortion.

MO-1008 / 4008 / 1016 / 4016 User’s Guide

ꢀ Press PTT before you start talking and release PTT after

you have finished speaking.

ꢀ Your radio doesn’t allow you to talk and receive

simultaneously, so keep your transmission short. When

you are transmitting, other people can not. Use common

sense and do not occupy the channel too much.

ꢀ The radio might be programmed with a timeout timer

which will automatically end your transmission after a

preset time. In this case release PTT and wait for a few

seconds. The radio transmitter will be enabled again after

a few seconds. Ask your dealer or communications

coordinator for further details.

ꢀ The radio might be programmed for busy channel lock

out, which automatically disables the transmitter if your

channel is busy. In this case wait until the channel is

clear.

Scanning Channels

If you have more than one channel programmed, your MO-1008

/ MO-4008 / MO-1016 / MO-4016 may be programmed to allow

you to scan them. To activate scan press and release the

programmed function button. The radio will begin checking all

channels in the scan list for activity. The scan icon will blink while

the radio is scanning. To turn scan off press and release the

programmed function button again. If beeps are enabled a high

pitched beep will sound when scan is activated and a lower

pitched beep will sound when scan is turned off.

The scan list is programmed by your dealer or communications

coordinator. Your dealer may also have designated one or two

channels in the scan list as a priority channel. The priority

channel is checked for activity more often than other channels in

the scan list. The priority channel may also be checked for

activity while the radio is receiving on a non-priority channel.

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Once the receive signal ends, the radio may be programmed to

wait a period of time before resuming scan. When the scan hang

timer has expired, scanning will resume. This scan hang timer

will also be started whenever the radio has ceased transmitting

on a channel. Your dealer or communications coordinator will

customize the scan options for your particular situation; the

following paragraphs detail the available options.

Busy Channel Scan

If no priority channel has been assigned by your dealer or

communications coordinator, all channels in your scan list will be

checked for activity, with no preference given to any channel. If

activity is detected on a channel the radio will stop on that

channel. While the radio is stopped on a channel it may be

deleted from the scan list by pressing a programmed scan skip

function button. When the radio is turned off, all channels

removed from the scan list using nuisance channel delete will be

restored.

Priority Channel Scan

If a priority channel (or two) has been assigned by your dealer or

communications coordinator, the priority channel will be checked

more often than the other channels in the scan list. If activity is

detected on a channel the radio will stop on that channel. While

stopped on a non-priority channel, the radio may be programmed

to check for activity on the priority channel. This may be referred

to as priority channel lookback, and the receive audio from the

non-priority channel will be briefly interrupted while priority

lookback occurs. While the radio is stopped on a non-priority

channel it may be deleted from the scan list by pressing a

programmed scan skip function button. This function may be

referred to as nuisance channel delete. The priority channel can

not be deleted from the scan list. When the radio is turned off, all

channels removed from the scan list using nuisance channel

delete will be restored.

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Priority Select Scan

If channel select priority scan has been programmed by your

dealer or communications coordinator, the channel selected

when scan is turned on will be assigned as the priority channel.

Operation will otherwise follow the priority channel scan

conventions.

Transmitting While in Scan Mode

If PTT is pressed while the radio is in scan mode, your dealer or

communications coordinator may have programmed one of the

following options for the transmit channel:

1. When PTT is pressed, the radio will generate an error beep

because your dealer or communications coordinator has

programmed the radio to not allow transmission while the

radio is in scan mode.

2. When PTT is pressed, the radio will switch to and transmit

on the priority 1 channel, priority 2 channel or other dealer

programmed channel regardless of the current receive state.

This mode may be referred to as priority only transmit.

3. If the radio has stopped on a channel, or the scan hang

timer is active, the radio will transmit on the scan stop

channel when you press PTT. If you press PTT, while the

radio is scanning channels, the radio will switch to and

transmit on the priority 1 channel, priority 2 channel or other

dealer programmed channel. This mode may be referred to

as (priority) talkback transmit.

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Programmable Functions

For increased flexibility and customization, the 6 front panel

buttons [∼], [ ], [A], [B], [C] and [D] may be programmed with

the following functions:

† Call Alert

Press and release this button to enable the horn output. After a

2-tone sequence is decoded the horn output will activate as

programmed.

† Call Reset

Press and release this button to mute the radio until a 2-tone

sequence is decoded.

† Call Send

Press and release this button to send the programmed 2-tone

encode sequence.

† Channel Up

Press and release this button to increment the radio to the next

channel. Press and hold to scroll channels.

† Channel Down

Press and release this button to decrement the radio to previous

channel. Press and hold to scroll channels.

† Emergency

Press and hold this button to activate the emergency function.

The programmed emergency response will be performed.

† Keylock

Press and hold for one second to lock all other front panel keys.

Press and hold again to unlock.

† Memory Channel 1 & 2

Press and release the programmed button to switch to the

assigned (preset) channel. If allowed by dealer programming,

MO-1008 / 4008 / 1016 / 4016 User’s Guide

press and hold the programmed function button to assign the

current channel as the 1^stor 2^ndmemory channel.

† Unsquelched Monitor

Press and release this button to disable 2-tone, CTCSS, DCS

and noise squelch. Once activated, press any button to disable

unsquelched monitor mode.

† Normal Monitor

Press and release this button to disable 2-tone, CTCSS and

DCS signaling. Once activated, press any button to disable

normal monitor mode.

† Latched Normal Monitor

Press and release this button to disable 2-tone, CTCSS and

DCS signaling. Once activated, the latched normal monitor

remains active until this button is pressed again.

† Panel Display

Press and release this button to turn off the LCD and

backlighting. Press again to turn the display back on.

† Public Address

Press and release this button to activate public address mode.

Press again to return to normal radio operation.

† Scan

Press and release this button to activate scan. Press again to

turn scan off.

† Scan Skip

While scan is paused on a channel, press this button to

temporarily delete the pause channel from the scan list. While

scan is off, press this button to remove the selected channel

from the scan list or add it back if it was previously deleted. The

scan list will be reset to the dealer programming when the radio

is turned off.

† Squelch Level

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Press and release this button and use the up and down keys to

change the noise squelch level for the current channel. The

squelch range is 0-16 with 1 being the most sensitive level.

Selecting 0 will disable the noise squelch circuit. Press the

squelch button again to exit squelch level mode.

† Talk Around

Press and release this button to shift the radio transmit

frequency to the programmed channel receive frequency. This

allows the radio to communicate directly with other radios, which

normally communicate through a repeater system. Press again

to change back to the programmed transmit frequency.

† Tx Power

Press and release this button to toggle the transmit power

between the high and low power levels.

Message Display Quick Reference

Error Codes

Display

Description

No response from EEPROM

PLL unlock

EEPROM data error

Radio high temperature

Cloning error

Serial communication error

Low battery voltage

High battery voltage

Password entry error

Incorrect radio model

Radio mode error

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Function Codes

Display

Description

Individual call

Group call

All call

Kill call

Resurrection call

ANI start call

No function assigned to key

Scan start

Channel restored to scan list

Channel removed from scan list

Talk around on

Talk around off

0-15

Current channel squelch level

Key lock on

Key lock off

Emergency function activated

Public address on

Public address off

Call alert enabled

Current channel assigned as memory channel

High or low transmit power

DTMF or 2TONE call encode

Hook alert on

M1 or M2

TH or TL

Hook alert off

Tuning mode

Programming mode

Clone mode data receive

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Clone mode start

Password prompt

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Specifications

General specifications

Frequency range

FCC ID number

MO-1008/1016 (VHF)

MO-4008/4016 (UHF)

430-470 MHz

MMAMO4032

Part 90

136-174 MHz

MMAMO1032

Part 90

FCC type acceptance

Maximum number of channels

Channel spacing

8/16

12.5/25 KHz

5/6.25/7.5 KHz

50 CTCSS/104 DCS

13.6 Vdc ±15%

810

12.5/25 KHz

Channel stepping

CTCSS/DCS per channel

Input voltage

5/6.25/7.5 KHz

50 CTCSS/104 DCS

13.6 Vdc ±15%

810

MIL spec

Size (HxWxD)

1.73x6.45x6.38 in

(44x164x162 mm)

3.3 lbs (1.5kg)

1.73x6.45x6.38 in

(44x164x162 mm)

3.3 lbs (1.5kg)

Weight

EIA/TIA-603 receiver specs

Frequency stability

12 dB SINAD sensitivity

Selectivity

±2.5 ppm (-30° to +60° C)

0.25 µV

±2.5 ppm (-30° to +60° C)

0.25 µV

70 dB WB/65 dB NB

±2 KHz WB/±1 KHz NB

70 dB WB/65 dB NB

±2 KHz WB/±1 KHz NB

Intermodulation rejection

Spurious rejection

Acceptable radio frequency

displacement

Squelch sensitivity

Audio response

<12dB Sinad

per EIA/TIA-603 specs

4 Watts <5% THD into 8Ω

50 Ω

<12dB Sinad

per EIA/TIA-603 specs

4 Watts <5% THD into 8Ω

50 Ω

Audio output

RF input impedance

EIA/TIA-603 transmitter specs

RF power output

50 Watts or 5 Watts

±2.5 ppm (-30° to +60° C)

16KOF3E/11KOF3E

70 dB WB/60 dB NB

70 dB

45 Watts or 5 Watts

±2.5 ppm (-30° to +60° C)

16KOF3E/11KOF3E

70 dB WB/60 dB NB

70 dB

Frequency stability

Modulation type

Adjacent channel emissions

Spurious emissions

FM hum & noise

45 dB WB/40 dB NB

per EIA/TIA-603 specs

45 dB WB/40 dB NB

per EIA/TIA-603 specs

Audio response

Audio distortion

<5% 1 KHz @ 60%

deviation

<5% 1 KHz @ 60%

deviation

RF output impedance

50 Ω

MO-1008 / 4008 / 1016 / 4016 User’s Guide

MO-Series Connectors

1 RxD

2 Gnd

3 TxD

4 Hook

5 Mic

6 Ptt

7 +8 Vdc

8 FlashMode

MO-Series microphone jack

6 PTT

11 Discriminator Out

7 RxAudio Out

12 RxD

8 Decode Valid

13 Ground

9 TxD

14 Switched 13.6 Vdc

10 Mic Modulation In

15 Subaudible In

MO-Series option connector

5 HookSwitch

4 Call Alert

3IgnitionSense

2 Speaker 2

1 Speaker 1

MO-1008 / 4008 / 1016 / 4016 User’s Guide

Warranty Statement

Midland Radio Corporation (herein, Midland) warrants each new radio product manufactured

or supplied by it to be free from defects in material and workmanship under normal use and

service for a period listed below, provided that the user has complied with the requirements

stated herein.

The Warranty period begins on the date of purchase from an Authorized Midland Sales and

Service Outlet. This Warranty is offered to the original end user and is not assignable or

transferable. Midland is not responsible for any ancillary equipment attached to or used in

conjunction with Midland products.

Midland offers to the original end user a Two (2) Year Limited Warranty on Midland Business

and Industrial radio products. Accessories carry a One (1) Year Limited Warranty.

During this period, if the product fails to function under normal use because of manufacturing

defect(s) or workmanship, it should be returned to the Authorized Midland Sales and Service

Outlet from which it was purchased. The Sales and Service Outlet will repair the product or

return the product for repair to Midland or its Authorized Repair Depot. The user is

responsible for the payment of any charges or expenses incurred for the removal of the

defective product from the vehicle or other site of its use; for the transportation of the product

to the Sales and Service Outlet; for the return of the repaired / replacement product to the

site of its use and for the reinstallation of the product.

Midland shall have no obligation to make repairs or to cause replacement required, which

results from normal wear and tear or is necessitated in whole or in part by catastrophe, fault

or negligence of the user, improper or unauthorized alterations or repairs to the Product,

incorrect wiring, use of the Product in a manner for which it was not designed or by causes

external to the Product. This Warranty is void if the product serial number is altered, defaced

or removed.

Midland’s sole obligation hereunder shall be to replace or repair the Product covered in this

Warranty. Replacement, at Midland’s option, may include a similar or higher-featured

product. Repair may include the replacement of parts or boards with functionally equivalent

reconditioned or new parts or boards. Replaced parts, accessories, batteries or boards are

warranted for the balance of the original time period. All replaced parts, accessories,

batteries or boards become the property of Midland.

THE EXPRESS WARRANTIES CONTAINED HEREIN ARE IN LIEU OF ALL OTHER

WARRANTIES, EITHER EXPRESSED OR IMPLIED OR STATUTORY, INCLUDING,

WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE.

FOR ANY PRODUCT WHICH DOES NOT COMPLY WITH THE WARRANTY SPECIFIED,

THE SOLE REMEDY WILL BE REPAIR OR REPLACEMENT. IN NO EVENT WILL

MIDLAND BE LIABLE TO THE BUYER OR ITS CUSTOMERS FOR ANY DAMAGES,

INCLUDING ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES,

OR FOR THE LOSS OF PROFIT, REVENUE OR DATA ARISING OUT OF THE USE OF

OR THE INABILITY TO USE THE PRODUCT.

This warranty is void for sales and deliveries outside of the U. S. A. and Canada.

ꢀ This device complies with Part 15 of the FCC Rules. Operation is

subject to the condition that this device does not cause harmful

interference.

ꢀ This radio operates in FCC regulated frequency bands. All radios

must be licensed by the FCC before use. Because this radio

contains a transmitter, Federal law prohibits unauthorized use or

adjustments of this radio.

MO-1008 / 4008 / 1016 / 4016 User’s Guide

1120 CLAY STREET, NORTH KANSAS CITY, MISSOURI, 64116

PHONE: (816) 241-8500, FAX: (816) 241-5713

www.midlandradio.com

Printed in Malaysia

Krups Convection Oven FEM3 User Manual
Kustom Musical Instrument Amplifier KG1 User Manual
Lexicon Recording Equipment CP 3 User Manual
Liebert Power Supply 350VA to 1000VA User Manual
Lochinvar Water Heater 0502 1302 User Manual
Lowrance electronic GPS Receiver HD LCX 110C User Manual
Magic Chef Microwave Oven MCB1110W User Manual
Marvin Window Window User Manual
Master Bilt Refrigerator TAC 27HDSA User Manual
MB QUART Speaker RKC110 User Manual