INSTALLATION INSTRUCTIONS FOR PART 99-7875/99-7875T
APPLICATIONS
Honda Accord 2008-2010
(For Non-Navigation models with Dual Zone Climate controls)
Honda Accord Crosstour 2010
99-7875/99-7875T
KIT FEATURES
• Painted To Match Factory Dash
99-7875=Charcoal, 99-7875T=Taupe
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket
C
B
D
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
A
Harness:
• 70-1729 - Honda harness 2008-up
• 70-1730 - Honda amp interface harness 2008-up
Antenna Adapter:
• 40-HD10 - Honda antenna adapter 2005-up
F
E
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Cutting Tool
1-800-221-0932
© COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION
99-7875/99-7875T DASH DISASSEMBLY
HONDA ACCORD 2008-10 / CROSSTOUR 2010
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
2
3
4
A
Unclip and remove the trim panel
from above the glove box at the right
side of the factory radio. (Figure A)
Unclip and remove the trim panel at
the left side of the factory radio.
(Figure B)
B
Remove the (2) Phillips screws from
the left and right side of the of the
factory radio. (Figure C)
5
6
Unclip and remove the top of the cen-
ter console including the cup holders.
(Figure D)
Remove (2) Phillips screws at the bot-
tom edge of the pocket assembly.
(Figure E)
C
Remove (2) Phillips screws facing up
inside of the pocket below the factory
radio. (Figure F)
7
8
Unclip and remove the pocket assem-
bly. (Figure G)
Continue on page 2.
D
E
1
99-7875/99-7875T DASH DISASSEMBLY
HONDA ACCORD 2008-10 / CROSSTOUR 2010
9
Remove (2) Phillips screws facing up
on the bottom of the factory radio.
F
G
H
I
(Figure H)
10 Unclip the factory radio assembly.
Unplug and remove the radio assem-
bly. (Figure I)
11 Remove (6) Phillips screws securing
the climate controls to the factory
radio assembly and remove the con-
trols from the assembly. (Retain the
screws and climate controls for re-
use during kit preparation.)
12 Remove (4) Phillips screws securing
the a/c vents to the factory radio
assembly and remove the a/c vent
from the assembly. (Retain the
screws and a/c vents for re-use dur-
ing kit preparation.)
13 Unclip and remove the hazard
switch/passenger air bag light
assembly. (Retain the hazard
switch/passenger air bag light
assembly for re-use during kit prepa-
ration.)
14 Remove (4) Phillips screws securing
trim panel at the bottom edge of the
factory radio assembly and remove
the trim panel. (Retain the screws
and trim panel for re-use during kit
preparation.)
15 Remove (9) clips from the back of the
factory radio assembly. (Retain the
clips for re-use during kit prepara-
tion.)
Continue to kit preparation.
2
99-7875/99-7875T KIT PREPARATION
HONDA ACCORD 2008-10 / CROSSTOUR 2010
A
Snap the hazard switch/passenger air
bag light assembly into the radio
housing from front. (Figure A)
1
2
Secure the a/c vents into the radio
housing using the factory hardware
from rear. (Figure B)
3
4
Secure the climate controls into the
radio housing using the factory hard-
ware from rear. (Figure C)
B
Secure the trim panel onto the radio
housing using the factory hardware.
(Figure D)
5
Attach the clips to the back of the
radio housing. (Figure E)
Continue to kit assembly.
E
C
D
3
99-7875/99-7875T KIT ASSEMBLY
DIN MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
1
2
3
Slide the aftermarket radio into the
DIN cage until it snaps into place.
(Figure B)
Snap the pocket into the radio housing.
(Figure C)
Continue to final assembly.
B
C
4
99-7875/7875T KIT ASSEMBLY
ISO MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
1
Mount the ISO Brackets to the radio
using the screws supplied with the
radio. (Figure A)
2
3
4
Slide the radio into the Radio Housing
until it snaps into place. (Figure B)
Snap the Trim Plate onto the front of
the Radio Housing. (Figure C)
Snap the Pocket into the Radio
Housing. (Figure C)
Continue to final assembly.
5
99-7875/99-7875T KIT ASSEMBLY
DOUBLE DIN/STACKED ISO MOUNT UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
1
2
Cut and remove the center bar from
the Radio Housing. (Figure A)
Snap the Double DIN brackets to the
inside edge of the Radio Housing.
(Figure B)
3
4
Slide the Double DIN or stacked ISO
mount units into the bracket/radio
housing assembly and secure the
unit(s) to the assembly using the
screws supplied with the unit(s).
(Figure C)
Snap the Double DIN trim plate onto
the front of the Housing/Radio assem-
bly. (Figure C)
Continue to final assembly.
6
99-7875/99-7875T FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
7
99-7875/7875T
NOTES
8
99-7875/99-7875T
NOTES
9
99-7875/7875T INSTRUCTIONS
1-800-221-0932
REV. 04/21/10 © COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION INST99-7875
|