INSTALLATION INSTRUCTIONS FOR PART 99-7952
APPLICATIONS
2005-2007 Suzuki Aerio
99-7952
KIT FEATURES
• DIN head unit provision
• ISO DIN head unit provision
KIT COMPONENTS
A) Radio Housing l B) ISO Brackets | C) Trim Plate
A
C
B
TOOLS REQUIRED:
Phillips Screwdriver I Small Flat Blade Screwdriver I Utility Knife
1-800-221-0932
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
DASH DISASSEMBLY
99-7952
2005-2007 SUZUKI AERIO
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
2
Unclip and remove the trim panels
from both sides of radio/climate
controls. (Figure A)
Remove (4) Phillips screws holding
radio to sub dash and remove radio.
(Figure B)
3
4
B
Remove (4) )Phillips screws securing
the radio and brackets to the factory
radio trim panel. (Figure C)
75
AUTO
PUSH
PUSH 85
A/C
65
OFF
AUTO
PUSH
C
Rear View
1
KIT ASSEMBLY
DIN HEAD UNIT PROVISION
99-7952
Cut and remove the center bar in
the DIN opening of the 99-7952
Radio Housing.
A
1
2
3
Secure the 99-7952 radio housing to
the factory radio trim panel using
the factory hardware.
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure A)
B
Slide the aftermarket head unit into
4
the cage and secure. (Figure B)
2
99-7952
KIT ASSEMBLY
ISO DIN HEAD UNIT PROVISION
A
Cut and remove the center bar in
the DIN opening of the 99-7952
Radio Housing.
1
2
3
Secure the 99-7952 radio housing
to the factory radio trim panel using
the factory hardware.
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure A)
B
Slide the head unit into the radio
opening until the side clips engage.
4
5
(Figure B)
Snap the Trim plate into the Radio
Housing. (Figure B)
3
KIT ASSEMBLY
99-7952
FINAL ASSEMBLY
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
1
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
A
A)
B)
C)
D)
Strip wire ends back 1/2"
Twist ends together
Solder
B
C
D
Tape
METRA / EIA WIRING CODE
12V Ignition / Acc . . . Red
Right Front (+) . . . . . Gray
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-). . . . . . . White / Black
Right Rear (+). . . . . . Violet
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4
99-7952
NOTES
5
INST997952
1-800-221-0932
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
REV. 04/10/07
INST99-7952
|