E X E C U T I V E
B r a v i s s i m o 2 S S t e a m S t a t i o n I r o n
Model:
2 3 8 0 5
2100W
PLEASE READ ALL INSTRUCTIONS BEFORE USE
2 y e a r g u a r a n t e e
MW_EX233805 StteamStation_IM.indd
1
7/25/2007 2:02:50 PM
Steam ironing
-
Set the desired temperature with the
thermostat control (J), depending on the type
of cloth to be ironed (Fig. 3).
When you start to iron, proceed as follows:
-
Unscrew the cap (F) and fill the boiler with
water, using a jug (Fig. 1) (if you fill it with
hot water, the appliance will be ready for use
sooner).
Fig. 3
-
The appliance will be ready for use when the
pressure indicator LED (E) lights up (Fig. 4).
While ironing, this LED (E) goes on and off
automatically, this is normal.
Fig. 1
-
-
Even if the boiler has a certain level of water, it
is always recommended to fill it to the top for a
longer range, thanks to its large 1l capacity.
Carefully close the cap (F), screwing it to the
end.
-
-
-
Place the boiler on a flat , stable surface.
Plug the appliance into the mains.
Switch on the boiler and the iron by pressing
the relevant switches (B) and (A). The
corresponding LEDs will light (Fig. 2).
Fig. 4
-
By pressing the steam switch (H) you will get
a constant steam jet (Fig. 5). The steam stops
when you release the switch.
Fig. 2
Thermostat Control Fabric Type
Position
Steam
•
Nylon, Silk
Wool
No
No
Yes
••
•••
Cotton, Linen
Fig. 5
It is recommended not to use steam in the • and
•• thermostat positions, as water could drip.
MW_EX233805 StteamStation_IM.indd
4
7/25/2007 2:02:51 PM
-
-
Clean the base of the iron while it is still hot,
using a damp cloth, after each use.
How to fill the boiler while ironing
To fill the boiler, proceed as follows:
The rest of the appliance can also be cleaned
using a damp cloth. Never submerge the
appliance in water or any other liquid, or hold
it under a running tap. Do not use solvents or
abrasive products to clean it.
-
Eliminate steam pressure from inside the boiler
by switching on the steam switch (H) (Fig. 5).
Turn off the boiler (B) and iron (A) switches.
Unplug the appliance from the mains.
Carefully unscrew the cap (F) to let the residual
steam out of the boiler.
-
-
-
Care and Cleaning
-
-
Wait for some minutes and carefully pour 1l of
water into the boiler using a jug (Fig. 1).
Carefully close the cap (F) again, screwing it to
the end.
•
•
•
Before cleaning the iron, ensure it is
disconnected from the power supply and has
completely cooled down.
Deposits and other residues on the soleplate
can be removed with a rough cloth soaked in a
vinegar/water solution, or methylated spirits.
The housing/body may be wiped with a damp
cloth and then polished with a dry one.
Dot not use abrasives on the soleplate.
Keep the soleplate smooth: avoid hard contact
with metal objects.
Vertical ironing
It is possible to iron hanging curtains, garments
on their own hangers... (Fig. 6)
•
•
•
NOTE: Ironing dirty fabric or fabric not rinsed
fully will result in the iron sticking and dirt
accumulating on the bottom of the soleplate, as
will a iron set at too high a temperature for the
relevant fabric.
Fig. 6
-
-
Adjust the iron thermostat control (J) to the
maximum temperature.
Iron from top to bottom and press the iron
steam switch (H).
Important: For cotton and linen clothes, it is
recommended to put the base of the iron
in contact with the fabric. For more delicate
fabrics, it is recommended to keep the base of
the iron at a distance of some centimetres.
Dry ironing
-
-
-
Connect the professional iron to the mains.
Turn on the iron switch (A).
Set the iron temperature with the thermostat
control (J), depending on the fabric to be
ironed.
After each ironing
-
Switch off the professional iron by pressing
switches (B) and (A).
-
Unplug the network connection cable (G) from
the mains.
MW_EX233805 StteamStation_IM.indd
5
7/25/2007 2:02:51 PM
Trouble Shooting Guide
Problem
Reason
Action
Water drips from the holes
on the base of the iron when
turning on the steam switch
(H).
Iron thermostat control (J) is
set to the minimum position
• / ••
Set the thermostat control to
the steam zone •••
The boiler is too full.
Remove some water.
The boiler is in a tilted position.
The switch (A) is “off”.
Iron thermostat control (J) set
to the minimum position.
Faulty power connection.
Empty boiler
Place it on a horizontal surface.
Switch it to “on” (A)
The iron does not heat and the
LED (K) does not light up.
Adjust the thermostat control.
Check the power points.
Fill the boiler with water
Switch them on
No steam comes out when
pressing the steam switch (H)
Leak from the boiler filler cap
Switches (B) and (A) are “off”
Cap (F) not properly closed
Let the boiler cool and screw
the cap (F) to the end again
Go to an authorised Technical
Service Centre
Safety valve activated
The boiler cap (F) does not
unscrew easily
There is steam remaining inside
the boiler
Press the steam switch (H) to
let the steam out
MW_EX233805 StteamStation_IM.indd
6
7/25/2007 2:02:51 PM
MW_EX233805 StteamStation_IM.indd
8
7/25/2007 2:02:51 PM
|