Bluesbreaker II Suggested Settings
BOOST (Amp: Slightly Distorted)
BLUES LEAD (Amp: Clean)
BB-2 Bluesbreaker II
FUNKY BLUES (Amp: Clean)
HOT HARMONICS (Amp: Clean)
Owners Manual
WARNING!
4
IMPORTANT Precautions
2
3
6
7
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
From The Chairman
WARNING
I would like to personally thank you
for selecting one of our effects pedals.
Do not expose the apparatus to rain or moisture. Do not expose
the apparatus to dripping or splashing. No objects filled with
liquids should be placed on or near the apparatus. Do not use
this apparatus near water.
For over 40 years the Marshall name has been synonymous
with the greatest guitar tones in music. We have worked hand
in hand with guitarists from all levels throughout the world to
maintain and improve that special ingredient, ‘The Marshall
Sound.’
5
Clean only with dry cloth.
1
8
Changes or modifications not expressly approved by Marshall
Amplification plc could void the user’s authority to operate the
equipment.
Our range of effects pedals gives the opportunity to augment
the classic Marshall tone to add Marshall character to a guitar
set-up.
All our pedals are made with the same utmost attention to
quality, in both materials and manufacture as our world
renowned amplifiers, cabinets and combos, in order to provide
you with optimum reliability and tone.
I would like to wish you every success with all of your musical
endeavours and also your new Marshall effects pedal, which I
am sure you will find a pleasure to play for many years to
come.
9
Heed all warnings.
Follow all instructions.
Keep these instructions.
Yours Sincerely,
European Product Only
1
In Blues Mode all controls are operational and the
Bluesbreaker II will give your guitar a wonderfully creamy,
natural sounding bluesy overdrive. This mode is great when
using a clean amp but can also be used with an amp that is
already distorting for extra Marshall mayhem.
Trouble Shooting
3. Drive
This increases the amount of distortion, taking you from
vintage breakup, ideal for big crunchy chords and sweet
singing blues, to full on overdrive.
WHAT IF
NO
OUTPUT
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
N.B. This control is only operational when on Blues mode.
4. DC Input
For input of a 9V DC adaptor should you not wish to use
batteries.
NOISE IN
BYPASS
5. LED
INDICATOR
LED NOT
ON
Indicates when the Bluesbreaker II is in operation.
INPUT
LEAD
6. Tone
The Bluesbreaker II features pre-set bass and mid controls, for
optimum response. This Tone control effects the treble region
of your tone adding brightness and cut.
SOUND TOO
TREBLY OR
FIZZY
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
N.B. This control is only operational when on Blues mode.
SOUND TOO
MUSHY OR
BASSY
ꢀ
ꢀ
ꢀ
7. Volume
Controls the volume of the pedal.
When in Boost mode this governs the level of the signal
driving into the amplifier. The more the level is increased the
more you will push the amp into distortion.
When in Blues mode this control allows you to set a different
volume level for solos etc.
ꢀ
UNUSUAL
FEEDBACK
REDUCE
TREBLE
REDUCE
TREBLE
ꢀ
ꢀ
ꢀ
UNUSUAL
HUM
8. In Jack Socket
This is the input jack, for connection to your guitar or to
another effects pedal if you are linking pedals together.
MOVE AWAY
FROM AMP
ꢀ
BASS
FEEDBACK
PICKUPS
MAY BE
VIBRATING
9. Foot Switch
For switching the Bluesbreaker II on and off.
4
5
Battery Replacement
1. To replace the battery, open
the easily accessed coin
screw battery cover plate by
loosening screw as shown,
then disconnect the battery
connector lead.
2. Use PP3 or equivalent
battery (for improved
battery life use alkaline type)
3. Always ensure that the
battery is removed when the
pedal is not in use for long
periods.
4. Dispose of old battery
in a safe place.
Technical Specification
Power: 9V DC Centre Negative Regulated
Current Draw: 8mA
Controls: Blues/Boost Mode Select, Drive, Tone & Volume
Switches: On/Off Switch
Indicators: On/Off LED
Jacks: Input/Output ‘Jacksockets’
Input Impedance: 1MΩ
Output Load Impedance: max 25kΩ
Dimensions: 120mm x 65mm x 55mm
Weight: 510 grammes
d from Www.Somanuals.com. All Manuals Search And D
6
|