VCR
VR402BMG
VR602BMG
Video Ca ssette Recorder
Hookup Pa ges
Hookups Without a Cable Box/Direct Broadcast System (cont’d) 7
3
Connect the RF coaxial cable (supplied) to the O UT Jack on the back of the
VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on
type (supplied) or screw-on type of coaxial cable, whichever you prefer.)
AUDIO
ANT
L
IN
OUT
IN
R
VIDEO
OUT
Antenna
or Cable
CH3 CH4
OUT
IN
ANT
AUDIO
L
IN
75
ANT /
CABLE
75⍀
ANT
CABLE
/
IN
OUT
R
OUT
VIDEO
ANTENNA IN Jack
(on back of TV)
exam ple only
CH4
IN CH3
OUT
RF coaxial cable
4
Plug in the TV and the VCR.
5
Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever
channel is not used or least used in your area. Set the TV to the sam e channel. For
example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on
channel 03.
AUDIO
ANT
L
IN
OUT
IN
R
CH 4
or
CH 3
VIDEO
OUT
CH3 CH4
OUT
IN
ANT
AUDIO
L
IN
CH3 / CH4
Switch
IN
OUT
R
OUT
VIDEO
CH4
IN CH3
CH3
CH4
OUT
6
You are ready to turn on the VCR. Please go to page 11 before turning on the
VCR.
8 Hookups With a Cable Box/Direct Broadcast System
There are two ways to connect your Cable Box/DBS to the VCR. With this connection:
● You may view any channel.
● You must select channels at the Cable Box/DBS. Channels cannot be changed at the VCR.
● You may not view a channel other than the one you are recording.
● You may not program channels at the VCR.
● You can only program a timer recording for one channel at a time. Set the TV and the VCR to the Cable
Box/DBS output channel (channel 03 or 04); set the CH3/CH4 switch to the same channel. Set your Cable
Box/DBS to the channel you want to record. When you enter the channel you want to record in a timer
recording, select channel 03 or 04 (the Cable Box/DBS output channel). (This is step 5 on page 29.) Leave the
Cable Box/DBS on for a timer recording.
VCR
Cable Box/DBS
2
1
75
ANT /
CABLE
IN
OUT
ANT
AUDIO
L
IN
OUT
RF coaxial
cable
R
VIDEO
OUT
Cable
Signal
CH3 CH4
IN
OUT
TV’s
ANTENNA IN
Jack
RF coaxial
cable
3
Connections
1
Connect a Cable signal to the IN Jack on the Cable Box/DBS.
2
Use an RF coaxial cable (supplied) to connect the OUT Jack on the Cable
Box/DBS to the ANT(enna) IN Jack on the VCR.
3
Use a second RF coaxial cable to connect the OUT Jack on the VCR to the
TV’s ANTENNA IN Jack.
Recording/Viewing Any Channel
1
With the VCR on and in VCR position (the VCR Light will appear on the display
panel), use the CHANNEL o/p buttons to set the VCR to the Cable
Box/DBS output channel (channel 03 or 04). Set the CH3/CH4 switch
to the sam e channel.
2
Set the TV to the sam e channel to which you set the VCR.
3
Select the channel you want to view/record at the Cable Box/DBS.
Hookups With a Cable Box/Direct Broadcast System (cont’d) 9
With this connection:
● You may watch one channel while recording another.
● You may not record scrambled channels.
VCR
1
Cable Box/DBS
75
ANT /
CABLE
2
AUDIO
L
ANT
IN
OUT
R
IN
OUT
VIDEO
OUT
IN CH3
OUT
RF coaxial
cable
Cable
Signal
TV’s ANTENNA
IN Jack
RF coaxial
cable
3
Connections
1
Connect a Cable signal to the VCR’s ANT(enna) IN Jack.
2
Use an RF coaxial cable (supplied) to connect the OUT Jack on
the VCR to the IN Jack on the Cable Box/DBS.
3
Use a second RF coaxial cable to connect the OUT Jack on the
Cable Box/DBS to the ANTENNA IN Jack on the TV.
Recording O ne Channel/W atching Another
1
Put the Cable Box/DBS on the sam e channel as the
VCR’s CH3/CH4 switch. Set the TV to the Cable
Box/DBS output channel (03 or 04).
Then, with the VCR in VCR position (the VCR Light will appear
on the display panel), use the CHANNEL o/p buttons to
select the channel you want to record at the VCR. Start
the recording.
Helpful Hint
2
Press the VCR/TV button once to put the VCR in TV
position. (The VCR Light will disappear.)
• When you play a tape, make sure
the Cable Box/DBS is set to the
same channel as the CH3/CH4
switch on the VCR. Set the TV to
the Cable Box/DBS output channel
(03 or 04).
3
Select the channel you want to watch at the Cable
Box/DBS.
10 Hookups with a Stereo TV
antenna or
cable to
ANT(enna)
IN Jack
VR602BMG
1
AUDIO
L
ANT
IN
OUT
IN
R
VIDEO
OUT
CH3 CH4
OUT
IN
Audio and Video
IN Jacks on TV
VIDEO (yellow) and
AUDIO (red and white)
OUT Jacks
Video Cable
2
Stereo Audio Cable
3
3
antenna or
VR402BMG
cable to
ANT(enna)
IN Jack
1
ANT
IN
AUDIO
IN
OUT
OUT
CH3 CH4
Audio and Video
IN Jacks on TV
VIDEO
VIDEO (yellow) and
AUDIO (white) OUT Jacks
Video Cable
2
Audio Cable
● Audio and Video cables are not supplied.
1
Connect the antenna or cable to the ANT(enna) IN Jack on the back of the VCR.
2
Connect a video cable to the yellow VIDEO O UT Jack on the back of the VCR. Then, connect
the other end of the video cable to the VIDEO IN Jack on your TV.
3
VR602BMG: Connect a stereo audio cable to the red and white AUDIO OUT Jacks on the back
of the VCR, m atching cable colors to the jack colors. Then, connect the other end of the audio
cable to the AUDIO IN Jacks on your TV, again m atching cable colors to the jack colors.
VR402BMG: Connect an audio cable to the white AUDIO OUT Jack on the back of the VCR.
Then, connect the other end of the audio cable to the AUDIO IN Jack on your TV.
(If your TV has Right and Left AUDIO IN Jacks, you must use a “Y” splitter audio cable as illustrated to deliver
audio to the TV’s right and left channels.) This hookup will not give you stereo sound. To get stereo sound, use
the connections on pages six - seven and select the channel to be viewed at the TV (with the VCR turned off).
4
Turn on your TV, making sure it is in Line Input mode. Please refer to your TV owner’s manual for details.
22 Front Panel
PAUSE Button
While recording, press to pause the recording. Press again to
resume recording. Details are on page 25. You can not pause a
One-Touch Recording. During tape playback, press to freeze the
picture. Press again to resume playback. Details are on page 36.
Rem ote Sensor
Receives a signal from your
remote control so you can
operate your VCR from a
distance.
F.FW D (Fast Forward) Button
When playback is stopped, press to fast forward the
tape at high speed. During tape playback, press to fast
forward the tape while the picture stays on the screen.
Details are on page 36. Press to advance to the next
menu or to change the setting of an item in the menu.
PO W ER Button
Press to turn the
VCR power on and off.
PLAY Button
VIDEO In Jack
Press to play a tape. Press to release Slow, Search,
or Still mode and return to playback. Details are on
page 36. Press to select an item in the menu.
Connect a cable coming
from the video out jack of
a camcorder, another VCR,
or an audio-visual source
(laser disc player, video disc
player, etc.) here. Details
are on page 32.
REW (ind) Button
When playback is stopped, press to rewind
the tape at high speed. During playback, press
to rewind the tape while the picture stays on
the screen. Details are on page 36. Press to
return to a previous menu.
VR602BMG
REW
F.FWD
PLAY
REC/OTR
PAUSE
MENU
POWER VCR/TV
CHANNEL
STOP/EJECT
VIDEO
L AUDIO R
STATUS/EXIT
CHANNEL (p/o) Buttons
Press to change channels at the
VCR. Or, press to adjust the
tracking of a tape during normal
playback or slow motion play-
back. Also, press to remove
vertical jitter in a Still picture.
AUDIO In Jacks
Connect audio cables coming
from the audio out jacks of a
camcorder, another VCR, or an
audio source here. Details are on
page 32.
The VR602BMG is shown here. The
VR402BMG has only one AUDIO
IN jack.
STATUS/EXIT Button
Press to access or remove the
on-screen status display. Details are
on page 20. Press to exit on-screen
menus.
VCR/TV Button
Press to select VCR or TV position.
● VCR Position
Use to watch a tape, to watch a program while
recording it, or to watch a TV program (chang-
ing channels at the VCR). When the VCR Light
appears on the display panel, the VCR is in VCR
position.
REC(ord)/O TR Button
Press once to start a recording. Press
repeatedly to start a One-Touch
Recording. Details are on page 27.
STO P/EJECT Button
● TV Position
Press once to stop the tape. When playback is
stopped, press to eject the tape. Press to select an
item in the menu.
Use to watch TV (changing channels at the TV)
or to watch one program while recording anoth-
er. When the VCR Light does not appear on
the display panel, the VCR is in TV position.
MENU Button
Press to access the VCR menu.
Rear Panel 23
ANT(enna) IN Jack
Connect your antenna or cable
here. Details are on pages six-10.
AUDIO IN Jacks
Connect audio cables coming from the
AUDIO OUT Jacks of a camcorder,
another VCR, or an audio source here.
Details are on page 32.
The VR602BMG is shown here. The
VR402BMG has only one AUDIO IN jack.
AUDIO OUT Jacks
Connect audio cables going to the AUDIO IN
Jacks of a camcorder, another VCR, or an audio
system here. Details are on pages 32 and 38.
The VR602BMG is shown here. The VR402BMG has
only one AUDIO OUT jack.
VR602BMG
AUDIO
L
ANT
IN
IN
OUT
R
VIDEO
OUT
CH3 CH4
OUT
IN
VIDEO O UT Jack
Connect a video cable going to the VIDEO
IN Jack of a camcorder, another VCR, or an
audio-visual system (monitor, laser disc play-
er, video disc player, etc.) here. Details are on
pages 32 and 38.
CH3/CH4 Switch
Set to channel 3 or 4
to use your TV with
your VCR. Details are
on pages six-nine.
VIDEO IN Jack
Connect a video cable coming
from the VIDEO OUT Jack of a
camcorder, another VCR, or an
audio-visual source (laser disc
player, video disc player, etc.)
here. Details are on page 32.
AC Power Cord
Connect to a stan-
dard AC outlet to
supply power to the
VCR.
O UT Jack
Use the supplied RF coaxi-
al cable to connect this
jack to the ANTENNA IN
Jack on your TV, Cable
Box, or Direct Broadcast
System. Details are on
pages six-nine.
32 Rerecording (Tape Duplication)
The instructions on this page show you how to copy tapes. The illustration uses two VR602BMG VCRs.
Different VCRs may operate differently. To duplicate a tape, make the connections shown, then follow steps 1-7.
1. Audio cables from AUDIO O UT Jacks
of VCR 1 to AUDIO IN Jacks of VCR 2
VCR 1
Playing VCR
VCR 2 - Recording VCR
AUDIO
ANT
ANT
AUDIO
L
L
IN
IN
OUT
IN
OUT
IN
R
R
VIDEO
VIDEO
OUT
OUT
CH3 CH4
CH3 CH4
OUT
IN
IN
OUT
3. RF coaxial cable
from the OUT jack of
VCR 2 to the TV’s
ANTENNA IN Jack
2. Video cable from VIDEO O UT Jack
of VCR 1 to VIDEO IN Jack of VCR 2
● Audio and Video cables are not supplied.
1
Make the connections shown above.
Helpful Hints
2
VCR 1 will play your tape. Put a prerecorded tape in VCR 1.
• If you use the AUDIO and VIDEO IN
Jacks on the back of VCR 2, press
Number buttons 0, 0, 1 at step 5.
AV REAR will appear on the screen.
• If you use the AUDIO and VIDEO In
Jacks on the front of VCR 2, press
Number buttons 0, 0, 2 at step 5.
AV FRONT will appear on the
screen.
• Unauthorized recording of copyright-
ed television programs, video tapes,
or other materials may infringe on
the rights of copyright owners and
violate copyright laws.
• If a program has copyright protec-
tion, it may not record clearly.
• These instructions show you how to
copy tapes using two VCRs like
yours. Different VCRs may operate
differently.
3
VCR 2 will record your tape. Insert a blank tape in VCR 2. The
VCR must be in VCR position. (The VCR Light will appear on the dis-
play panel. If it does not, press the VCR/TV button once.)
4
Turn on the TV and set it to channel 03 or 04, whichever
channel the CH3/CH4 switch on VCR 2 is set to.
5
Point the rem ote control at VCR 2. Press the Num ber
buttons 0, 0, 1 or 0, 0, 2. (See Helpful Hints at right.)
6
Press the SPEED button to select SP or SLP at VCR 2.
• The VCR in the figure above is the
VR602BMG. If you have the
VR402BMG, use a single-plug audio
cable to connect the AUDIO OUT
jack on VCR 1 to the AUDIO IN jack
on VCR 2.
7
Press the PLAY button on VCR 1 and the REC(ord)/O TR
button on VCR 2 at the sam e tim e.
To stop recording, press the STOP/EJECT button on VCR 1, then
press the STOP/EJECT button on VCR 2.
|