Operating instructions
Page 12
GB
Combined refrigerator-freezer
7082 135-00
ECN 61 111
GB
Description of appliance and equipment
1
2
3
4
5
6
7
8
9
bl
bm
bn
Operating and control elements
Adjustable door racks
Adjustable storage shelves
Bottle rack
Type plate (behind the vegetable drawer on the left-hand side)
Drawer
Vegetable drawers
Water filter
Upper freezer drawer
Lower freezer drawer
IceMaker (in the interior of the upper freezer drawer)
Ventilation grille. In this area, the exchange of air for the refrig-
eration unit takes place. Never cover this grille or otherwise
obstruct the air flow.
Temperature and control display
Water filter has to be changed
Refrigerator temperature display
Operating and control elements
Menu mode is activated
The electronic control panel has the new "touch capacitance
technology". Any function can be activated by touching the cor-
responding icon.
(for setting additional functions)
Freezer temperature display
The exact contact point
is between the symbol and its label
Refrigerator
operating icons
Control
icons
Freezer
operating icons
Freezer operating icons
Refrigerator operating icons
Control icons
Temperature setting icons
Mute alarm (refrigerator and freezer)
Power failure LED
Freezer ON/OFF
SuperFrost
SuperCool
Dust filter LED
The dust filter in the appliance
plinth must be cleaned.
Refrigerator ON/OFF
Temperature setting buttons
IceMaker ON/OFF
SuperCool LED
Child lock LED
Alarm LED
IceMaker ON LED
SuperFrost LED
13
Water filter
Installing the water filter
Before switching on the appliance, install the water filter provided
in the interior rear wall of the refrigerator compartment.
This ensures good ice cube quality and keeps the water circuit
free of solids such as sand.
1. Remove the cover of the filter
socket.
Water filter
location
2. Insert the filter and turn it 90°
clockwise.
Replace the filter when the waterdrop
symbol appears in the temperature
display.
Filters can be obtained from your dealer.
Thedropsymbolmustbecancelledafter
the filter has been changed. For detailed
instructions see section entitled "Setup
mode".
Removing the water filter
Caution!
3. Turn the filter 90° anticlockwise
and remove.
To avoid the risk of bacteria growth, the water filter
must be changed when the waterdrop symbol appears
on the display!
It is not necessary to switch off the water supply when removing
or installing the water filter.
Saving energy
- Always ensure good ventilation. Do not cover ventilation open-
ings or grille.
- Always keep fan louvres clear.
- Do not place appliance in areas of direct sunlight or next to a
stove, heater or similar object.
- Theenergyconsumptiondependsontheinstallationconditions,
e.g. the ambient temperature.
- Keep the time the appliance is open to a minimum.
- Store food logically.
- Ensure that all food is well packed and covered for storage. This
will prevent frost from forming.
- First cool warm food to room temperature before storing it.
- Defrost frozen food in the refrigerator.
- If there is a thick layer of frost in the appliance: defrost the appli-
ance.
- Emptyandswitchoffrefrigeratingunitforlongervacationperiods.
- Use the vacation function for longer vacation periods.
Accumulated dust increases the energy consumption:
- Once a year, dust the refrigerating unit together with the metal
grille of the heat exchanger at the back of the appliance.
14
GB
Audible warning signal
Switching the appliance on and off
The appliance is equipped with an alarm function.
You are advised to clean the appliance before switching it on for
the first time (see "Cleaning").
Audible door alarm:
Do not load with frozen food until the temperature shows at least
-18°C. The refrigerator and freezer compartments can be oper-
ated separately.
If an appliance door is left open for more than 180 seconds,
the audible warning signal will sound. Touch the ALARM
icontocancelthealarm.Thealarmswitchesbacktostandby
when the door is shut.
Audible/visual temperature alarm:
Switching on: Touch the On/Off icons (on left
for refrigerator, on right for freezer) so that the
temperature displays light up or flash.
It sounds when it is not cold enough in the freezer compartment.
The temperature display and the
LED will also flash.
The audible warning device is switched off by touching the
ALARMicon.Thetemperaturedisplaywillcontinuetoflash
until the cause of the alarm has been rectified.
Switching off: Keep the On/Off icons pressed for approx. 3
seconds.
This can be caused by:
• the freezer door being left open for a long time, allowing warm
ambient air to enter;
Setting the temperature
The appliance is pre-set for normal operation. We recommend
temperatures of +5°C in the refrigerator and -18°C in the freezer.
• a long power failure;
• a fault in the appliance.
In each case, make sure food has not thawed or perished.
To reduce the temperature: Touch the
Down icon; on left for refrigerator and on
right for freezer.
To increase the temperature: Touch the
Up icon.
Power failure/FrostControl display
If the
LED lights up on the control panel, this means that the
- While you are entering the temperature, the set temperature will
flash on the display.
freezer temperature has risen too high during the last few hours
or days due to a power failure.
- When you touch the temperature setting icons for the first time,
the most recent setting ("reference setting") is displayed.
If you touch the ALARM icon now, the highest temperature
registered during the power failure will be displayed. Check
the quality of the food and its suitability for consumption in
case it has become too warm or even defrosted.
- You can change the settings in increments of 1°C by briefly touch-
ing the icons again. If the icons are held, the temperature setting
will change faster.
- Approximately 5 seconds after the last touch, the display will
automatically show the actual freezing or cooling temperature
("actual setting").
The highest temperature will appear for approx. 1 minute.
Afterthat,theactualtemperatureinthefreezerwillre-appear.
ThedisplaycanbeswitchedoffbytouchingtheALARMicon.
- You can change the temperatures
in the refrigerator: between 11°C and 2°C and
in the freezer: between -14°C and -28°C.
SuperCool
Touching the SuperCool icon switches the refrigerator compart-
ment to maximum cooling. It is recommended particularly if you
wish to cool large quantities of food, drinks, freshly baked goods
or meals rapidly.
Temperature display
In normal operation, the following settings will be displayed:
- the average refrigerator temperature and
- the warmest frozen food temperature.
Switching on: Touch the SuperCool icon briefly so that
When starting up for the first time or when the
appliance is warm, dashes will appear until
the temperature reaches a level that can be
displayed (below 0°C in the freezer).
the LED
comes on. The refrigerator temperature will
drop to its lowest value.
Note: The SuperCool function uses slightly more energy. After
approximately six hours, however, the refrigerator switches back
automatically to normal energy-saving operation. If required, the
SuperCool function can be switched off sooner.
The display will flash:
- if you change the temperature or
- if the temperature rises by several degrees, indicating cold loss,
e.g. if you place fresh, "warm" food in the freezer or if you remove
or re-pack frozen food the temperature may rise for a short time
due to warm air flowing into the freezer.
Switching off: Touch the SuperCool icon again until the LED
goes out.
If F1 to F5 appears in the display, the appliance has a fault. Con-
sult the customer service department indicating the fault number
displayed.
15
Setup mode
= Confirm water filter change
The following functions can be activated in setup mode:
= Child lock
Afterthewaterfilterhasbeenchanged,thedrop
symbol on the display must be reset.
Resetting the drop symbol
= Confirm water filter change
= Ice maker holiday mode
• Activate setup mode by touching the
SuperFrost icon for 5 seconds.
= Water quantity for ice-cube tray
= Display brightness
• Touch the freezer compartment Down icon
until appears in the display.
= Door gasket heating control
= Confirm dust filter cleaning
• Touch the SuperFrost icon.
- The display reads
Activating setup mode:
• Touch the SuperFrost icon again.
• Touch the SuperFrost icon for 5 seconds.
- The display reads
- The SuperFrost LED
- after 5 seconds will flash in the display.
The appliance is in setup mode now.
comes on for 5 seconds,
• The drop symbol disappears.
• Exit setup mode by touching
the freezer compartment On/Off icon.
You can select the setup mode functions by touching
the freezer compartment temperature setting icons.
= Ice maker holiday mode
Note: In setup mode the display will flash continuously.
See section entitled "Ice maker".
Exiting setup mode:
• Touch the freezer compartment On/Off icon
The appliance will change back to normal operation.
= Water quantity for ice-cube tray
If the produced ice cubes of the ice maker are too small, the inflow-
ing water quantity can be adjusted.
= Child lock
Adjusting the water quantity
The child lock is designed to protect the appliance from being
switched off accidentally.
• Activate setup mode by touching the SuperFrost icon for 5 sec-
onds.
Activating the child lock
• Touch the freezer compartment Down icon until
appears in the display.
• Activate setup mode by touching
the SuperFrost icon for 5 seconds.
• Touch the SuperFrost icon.
- The display reads
- The display reads
• Touch the SuperFrost icon.
• Touch the freezer compartment Up icon once only so that E 4
- The display reads
appears in the display.
• Touch the SuperFrost icon again.
Caution!
- The
LED is lit and the child lock is activated.
Do not increase for more than one step. If the adjusted value
is too high, the icecube tray of the ice maker could overflow.
• Exit setup mode by touching
the freezer compartment On/Off icon.
• Touch the SuperFrost icon again.
• Exit setup mode by touching the
freezer compartment On/Off icon.
Deactivating the child lock
• Activate setup mode by touching
Check the ice cube size within the next days. If the ice cubes are
still too small, follow the steps above again.
the SuperFrost icon for 5 seconds.
- The display reads
• Touch the SuperFrost icon.
- The display reads
• Touch the SuperFrost icon again.
- The
LED goes out. The child lock is deactivated.
• Exit setup mode by touching
the freezer compartment On/Off icon.
16
GB
Interior light
= Display brightness
Adjusting the display brightness
• Activate setup mode by touching the SuperFrost icon for 5 sec-
Theinteriorlightislocatedattheleft,rightandtopintherefrigerator
compartment and above each drawer in the freezer compartment.
It comes on if one of the doors or a freezer drawer is opened.
onds.
Caution-class1Mlaserradiation. Whencoverisremoved, do
not look directly at light through optical instruments. Severe
eye injury can occur.
• Touch the freezer compartment Down icon until appears in
the display.
• Touch the SuperFrost icon.
The light switches off automatically if one of the doors or a freezer
drawer has been left open for more than 15 minutes. The audible
warning signal sounds at the same time.
- The display reads
• Touch the freezer compartment
Up/Down icons to select
If one of the strip lights is not lit, it is defective.
0 = minimum to
The lighting may only be replaced by the customer service
technician or by competent skilled personnel!
5 = maximum brightness.
Do not try to change the defective lighting yourself!
• Touch the SuperFrost icon at the desired value.
• Exit setup mode by touching
the freezer compartment On/Off icon.
= Door gasket heating control
Condensed water on the gasket of the refrigerator doors can be
eliminated by activating the door gasket heating.
Activating the door gasket heating
• Activate setup mode by touching the SuperFrost icon for 5 sec-
onds
• Touch the freezer compartment Down icon until appears in
the display.
• Touch the SuperFrost icon.
- The display reads
• Touch the freezer compartment
Up/Down icons to select
= at slight condensation of the gasket,
= at heavy condensation of the gasket.
• Touch the SuperFrost icon at the desired value.
• Exit setup mode by touching
the freezer compartment On/Off icon.
= Confirm dust filter cleaning
Once the dust filter in the appliance plinth has been cleaned, the
dust filter LED
in the display must be cancelled.
Cancelling the dust filter symbol
• Activate setup mode by touching the SuperFrost icon for 5
seconds.
• Touch the freezer compartment Down icon until appears in
the display.
• Touch the SuperFrost icon.
- The display reads
• Touch the SuperFrost icon.
- The display reads
• The dust filter symbol has been cancelled.
• Exit setup mode by touching
the freezer compartment On/Off icon.
17
Arranging food
Equipment
Repositioning the door racks
Lift door rack vertically, lift out to
the front and re-insert at a different
height, following these steps in the
reverse order.
Repositioning the shelves
Light cover
1. Hold the shelf underneath
with your hand to prevent
from tipping down back-
wards when removing.
2. Lift the shelf at the front.
3. Pull the shelf towards you
until the round cutout of
the shelf is in line with the
interior light cover.
4. Lifttheshelfupandreplace
in the desired position.
Removing the shelves
(1) butter, cheese
(2) eggs
1. Follow the first three steps
(3) bottles
in the chapter above.
(4) frozen food, ice cubes
(5) meat, sausage products, dairy products
(6) baked goods, pre-cooked meals
(7) fruit, vegetables
2. Move the shelf down and
stopjustoverthevegetable
drawer.
3. Move the front of the shelf
upwards until the shelf is in
a vertical position.
Note
• Food which gives off or absorbs odours and flavours as well as
liquids should always be stored covered or in closed containers.
• High-percentage alcohols should be tightly sealed and stored
upright.
4. Turn the shelf by 90° and
remove.
• Fruit, vegetables and salad can be stored unpacked in the draw-
ers.
Removing the vegetable drawer
Pull the drawer straight out,
grip at the back and lift out.
Inserting the vegetable
drawer
Place the drawer on the pull-
outrails.Therailsmustbefully
extendedandalignedwiththe
front of the drawer. Slide the
drawer in.
18
GB
Freezer compartment description
Freezing with SuperFrost
Both drawers can be used for freezing of food or storage of frozen
Touch the SuperFrost icon briefly so that
food.
the
LED comes on.
Theice-cubebinintheupperdrawerisintendedforicecubesonly.
• For small amounts of frozen food switch on SuperFrost 6 hours
beforehand. For the maximum amount (see freezing capacity on
the type plate) you will need to switch it on 24 hours beforehand.
• Then place the fresh food inside the freezer.
If you need the whole upper drawer for freezing or storage, the
ice-cube bin can be removed.
Important: The ice maker will not eject the ice cubes of its tray if
- The SuperFrost function switches off automatically.Depending
on the quantity of food placed in the freezer, this will normally
be between 30 and max. 65 hours. The freezing process is now
complete, the SuperFrost LED will go out.
the bin has been removed.
Ice-cube bin
Ice maker
You should not switch on the SuperFrost function:
- when placing frozen food in the freezer;
- when freezing up to approx. 2 kg fresh food daily.
Space for freezing and
storage
Notes on freezing and storage
• Always store identical food items together.
• Packfoodwhichyouarefreezingyourselfinquantitiesappropriate
to your household.To ensure that the food freezes right through,
the following quantities should not be exceeded per package:
fruit, vegetables: up to 1 kg, meat: up to 2.5 kg.
• Pack frozen food in standard freezer bags or reuseable plastic,
metal or aluminium containers.
• Do not allow fresh food which is to be frozen to come into contact
with food already frozen. Always keep packs dry in order to avoid
them sticking together.
• Alwayswritethedateandcontentsonthepackanddonotexceed
the stated storage time for the food.
• Do not freeze bottles and cans which contain carbonated drinks
as they might burst.
• Onlytakeoutasmuchfoodasisimmediatelyrequiredforthawing.
Use food which has been thawed in prepared meals as quickly
as possible.
Freezing
Frozen food can be thawed in the following ways:
– in a fan oven,
Fresh food should be frozen to the core as rapidly as possible.
Frozen food can also be given a cold boost. This is provided by
the SuperFrost facility.
– in a microwave oven,
– at room temperature,
– in the refrigerator: the cold given off by the frozen food is used for
cooling.
The maximum amount of food (in
kg) which can be frozen in 24 hours
is shown on the type plate ("Freez-
ing capacity"). This amount varies
according to the model and climate
rating.
19
Ice maker
Safety instructions and warnings
Ice maker holiday mode
• Theicemakerisdesignedexclusivelytomakeicecubesinquanti-
ties required by a household and may only be operated with water
suitable for this purpose.
In case of longer vacations, the ice-cube tray should be emptied.
By setting the ice maker into the
holiday mode, the tray will
rotate down and no water
remains in the tray.
• All repairs and work on the ice maker may only be carried out by
customer service personnel or other trained personnel.
• Thefirstthreebatchesoficemustnotbeconsumedorused.
This applies both to using the appliance for the first time
and also to using it after it has not been used for a lengthy
period of time. This ensures that the water supply is purged.
The freezer drawer must be
left open so that the surface
of the tray dries up and no mould
or unpleasant odours can occur.
• Themanufacturercannotacceptliabilityfordamagecaused
by a faulty connection to the mains water supply.
• The ice maker will only work if the combined refrigerator-freezer
is connected to the electricity supply. It will only make ice cubes
if the freezer compartment is operating.
• Ensure that the drawer is fully closed, as the ice maker can oth-
Activating the ice maker holiday mode
Be sure the upper freezer drawer is com-
pletely closed and the ice-cube bin is
installed correctly.
erwise not produce ice cubes.
Switching the ice maker on
• Activate setup mode by touching the Su-
perFrost icon for 5 seconds.
Ice-cube bin
• Touch the IceMaker icon
so that the IceMaker LED
comes on.
• TouchthefreezercompartmentDownicon
until appears in the display.
After you start the ice maker for the first time, it may take up to
24 hours before the first ice cubes are ready.
The production capacity depends on the temperature inside the
freezer compartment. The lower the temperature, the more ice
cubes can be produced over a period of time.
• Touch the SuperFrost icon.
- The display reads
The ice cubes fall out of the ice maker into the ice-cube bin. When
the ice reaches a certain level in the bin, the appliance stops pro-
ducing ice automatically.
or
depending on whether the ice maker is switched
on or off.
Switching the ice maker off
If you do not need any ice cubes, the ice maker can be switched
off independently of the freezer compartment.
• Touch the freezer compartment Down icon.
- The display reads
• Touch the IceMaker icon
so that the IceMaker LED
• Touch the SuperFrost icon.
goes out.
- The digit flashes.
The ice-cube tray rotates down.
The ice maker can also be
switched on and off using the
ON/OFF button at the ice maker
housing.
When the interior temperature appears in the display, the tray is in
the down position and the ice maker is switched off automatically.
Press the button for approxi-
mately 1 second.
Defrosting
Refrigerator compartment
Therefrigeratorcompartmentdefrostsautomatically.Thewaterthat
formsontherearwalldrainsintoareservoiratthebackoftheappli-
ance and evaporates automatically through the compressor heat.
Freezer compartment
The NoFrost system automatically defrosts the appliance.
Any moisture arising collects on the evaporator and freezes, and
is periodically defrosted and evaporated.
20
GB
Cleaning
Malfunctions
Before cleaning always switch off the appliance. Pull out the
Yourapplianceisdesignedandmanufacturedforalengthy,reliable
operating life with no malfunctions. If a malfunction nonetheless
occurs during operation, check whether it is due to an operating
error. Please note that even during the warranty period the result-
ant servicing costs in this case will have to be borne by the owner.
mains plug or switch off or unscrew the fuse.
Clean the inside, equipment and outer walls with lukewarm water
and a little detergent. Do not use abrasive or acid cleaners or
chemical solvents.
You may be able to rectify the following faults by checking
Do not use steam cleaners because of the risk of injury and
the possible causes yourself:
damage.
Appliance does not function:
• Ensure that no cleaning water penetrates into the electrical com-
ponents or ventilation grille.
• Dry all parts well with a cloth.
– Is the appliance switched on?
– Is the plug correctly fitted in the mains socket?
– Is the fuse intact?
Loud running noise:
• Do not damage or remove the type plate on the inside of the ap-
– Is the appliance set up firmly on the floor?
– Does the appliance cause nearby items of furniture or objects to
vibrate? Please note that noises caused by the refrigerant circuit
cannot be avoided.
pliance. It is very important for servicing purposes.
• Use a commercially available stainless-steel cleaning agent for
stainless-steel appliances.
- Inordertoachievebestpossibleprotection,applyastainless-steel
care agent uniformly in grinding direction after cleaning. Points
which are darker at the start and a more intensive coloration of
the stainless-steel surface are normal.
- Donotuseabrasivespongesorscourers,donotuseconcentrated
cleaning agents and never use cleaning agents containing sand,
chloride or acid or chemical solvents, as these would damage the
surfaces and could cause corrosion.
The temperature is not low enough:
– Isthetemperaturesettingcorrect(see"Settingthetemperature")?
– Have excessive amounts of fresh food been placed in the appli-
ance?
– Doestheseparatelyinstalledthermometershowthecorrectread-
ing?
– Is the ventilation system working properly?
– Is the appliance set up too close to a heat source?
If none of the above causes apply
and you cannot rectify the fault
yourself, contact the nearest cus-
tomer service department stating
thetypedesignation ➊,index ➋and
appliance number ➌ as indicated
on the type plate. The type plate is
located inside the appliance on the
left-hand side (refrigerator).
Cleaning the dust filter
The dust filter in the appliance plinth must be cleaned at least
once a year.
1. Disconnect the appliance from the mains.
2. Pull the bottom freezer drawer right out.
3. Unscrew the ventilation grille.
Shutting your appliance down
If your appliance is to be shut down for any length of time, switch
it off and disconnect the plug or switch off or unscrew the fuse.
Clean the appliance and leave the door open in order to prevent
unpleasant smells.
The appliance complies with the relevant safety regulations and
EC Directives 2004/108/EC and 2006/95/EC.
All types and models are subject to continuous improvement and
the manufacturer therefore reserves the right to make modifica-
tions to the shape, equipment and technology.
4. Pushdownthebuttononthefilter,tiltthefilterforwards
and remove.
The dust filter can be washed in a dish-
washer or by hand using water and
detergent.
5. Dry the filter and then, in reverse order, replace it.
6. Re-attach the ventilation grille.
21
|