ThinkPad DVD Ultrabay Slim Burner
User’s Guide
ThinkPad DVD Ultrabay Slim Burner
User’s Guide
ATTENTION
Before installing this product, read the ThinkPad System Safety Booklet.
Note
Be sure to keep your proof of purchase, because it might be required for warranty services. See Appendix E, “Lenovo
First Edition (May 2007)
© Copyright Lenovo 2007.
Portions © Copyright International Business Machines Corporation 2005.
All rights reserved.
U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with
RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule
contract with Lenovo Group Limited, if any, or the standard terms of this commercial license, or if the agency is
unable to accept this Program under these terms, then we provide this Program under the provisions set forth in
Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in
Data-General, FAR 52.227.14 (Alternate III).
Contents
© Lenovo 2007. Portions © IBM Corp. 2005.
iii
iv ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Safety information
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
Antes de instalar este producto lea la información de seguridad.
© Lenovo 2007. Portions © IBM Corp. 2005.
v
Läs säkerhetsinformationen innan du installerar den här produkten.
vi ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
General safety guidelines
Always observe the following precautions to reduce the risk of injury and property damage.
Service
Do not attempt to service a product yourself unless instructed to do so by the Customer Support Center.
Use only a service provider who is approved to repair your particular product.
Note: Some parts can be upgraded or replaced by the customer. These parts are referred to as Customer
Replaceable Units, or CRUs. Lenovo expressly identifies CRUs as such, and provides
documentation with instructions when it is appropriate for customers to replace those parts. You
must closely follow all instructions when performing such replacements. Always make sure that
the power is turned off and that the product is unplugged from any power source before you
attempt the replacement. If you have any questions or concerns, contact the Customer Support
Center.
Power cords and power adapters
Use only the power cords and power adapters supplied by the product manufacturer.
Never wrap a power cord around the power adapter or other object. Doing so can stress the cord in ways
that can cause the cord to fray, crack or crimp. This can present a safety hazard.
Always route power cords so that they will not be walked on, tripped over, or pinched by objects.
Protect the cord and power adapters from liquids. For instance, do not leave your cord or power adapter
near sinks, tubs, toilets, or on floors that are cleaned with liquid cleansers. Liquids can cause a short
circuit, particularly if the cord or power adapter has been stressed by misuse. Liquids can also cause
gradual corrosion of the power cord terminals and/or the connector terminals on the adapter which can
eventually result in overheating.
Always connect power cords and signal cables in the correct order and ensure that all power cord
connectors are securely and completely plugged into receptacles.
Do not use any power adapter that shows corrosion at the ac input pins and/or shows signs of
overheating (such as deformed plastic) at the ac input or anywhere on the power adapter.
Do not use any power cords where the electrical contacts on either end show signs of corrosion or
overheating or where the power cord appears to have been damaged in any way.
Extension cords and related devices
Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you
use are rated to handle the electrical requirements of the product. Never overload these devices. If power
strips are used, the load should not exceed the power strip input rating. Consult an electrician for more
information if you have questions about power loads, power requirements, and input ratings.
Plugs and outlets
If a receptacle (power outlet) that you intend to use with your computer equipment appears to be
damaged or corroded, do not use the outlet until it is replaced by a qualified electrician.
© Lenovo 2007. Portions © IBM Corp. 2005.
vii
Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a
replacement.
Some products are equipped with a three-pronged plug. This plug fits only into a grounded electrical
outlet. This is a safety feature. Do not defeat this safety feature by trying to insert it into a non-grounded
outlet. If you cannot insert the plug into the outlet, contact an electrician for an approved outlet adapter
or to replace the outlet with one that enables this safety feature. Never overload an electrical outlet. The
overall system load should not exceed 80 percent of the branch circuit rating. Consult an electrician for
more information if you have questions about power loads and branch circuit ratings.
Be sure that the power outlet you are using is properly wired, easily accessible, and located close to the
equipment. Do not fully extend power cords in a way that will stress the cords.
Connect and disconnect the equipment from the electrical outlet carefully
Batteries
All personal computers manufactured by Lenovo contain a non-rechargeable coin cell battery to provide
power to the system clock. In addition many mobile products such as notebook computers utilize a
rechargeable battery pack to provide system power when in portable mode. Batteries supplied by Lenovo
for use with your product have been tested for compatibility and should only be replaced with Lenovo
approved parts.
Never attempt to open or service any battery. Do not crush, puncture, or incinerate batteries or short
circuit the metal contacts. Do not expose the battery to water or other liquids. Only recharge the battery
pack strictly according to instructions included in the product documentation.
Battery abuse or mishandling can cause the battery to overheat, which can cause gasses or flame to
“vent” from the battery pack or coin cell. If your battery is damaged, or if you notice any discharge from
your battery or the buildup of foreign materials on the battery leads, stop using the battery and obtain a
replacement from the battery manufacturer.
Batteries can degrade when they are left unused for long periods of time. For some rechargeable batteries
(particularly Lithium Ion batteries), leaving a battery unused in a discharged state could increase the risk
of a battery short circuit, which could shorten the life of the battery and can also pose a safety hazard. Do
not let rechargeable Lithium-Ion batteries completely discharge or store these batteries in a discharged
state.
Heat and product ventilation
Computers, AC adapters, and many accessories can generate heat when turned on and when batteries are
charging. Always follow these basic precautions:
v Do not leave your computer, AC adapter, or accessories in contact with your lap or any part of your
body for an extended period when the products are functioning or when the battery is charging. Your
computer, AC adapter, and many accessories produce some heat during normal operation. Extended
contact with the body could cause discomfort or, potentially, a skin burn.
v Do not charge the battery or operate your computer, AC adapter, or accessories near flammable
materials or in explosive environments.
v Ventilation slots, fans, and heat sinks are provided with the product for safety, comfort, and reliable
operation. These features might inadvertently become blocked by placing the product on a bed, sofa,
carpet, or other flexible surface. Never block, cover, or disable these features.
viii ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Chapter 1. About the drive
This manual provides information on registering, installing, and using the ThinkPad® DVD
Ultrabay™ Slim Burner, and is available on the Software and User’s Guide CD.
The appendixes of this guide contain warranty information and legal notices.
Product description
Your drive is compatible with the DVD-Multi Recorder specification, and can record as well as read
DVD-RAM, DVD-RW, and DVD-R (for General, 650 nm) media. Your drive can also record CD-R,
CD-RW, and High-Speed CD-RW media, and uses buffer underrun prevention technology for reliable CD
burning. Your DVD Burner can read many other formats including DVD+R, DVD+RW, DVD Video,
Video CD, audio CD, multiple-session, extended architecture (XA) CDs, and Kodak Photo CDs. (Some
DVD+R and DVD+RW media brands may not be compatible.) The drive is designed for installation in
your Ultrabay Slim Drive Bay or Ultrabay Enhanced Drive Bay.
Media
Write speed
24X Max.
16X Max.
8X Max.
8X Max.
4X Max.
4X Max.
6X Max.
6X Max.
5X Max.
CD-R
CD-RW
DVD-R
DVD+R
DVD+R double Layer
DVD-R dual layer
DVD-RW
DVD+RW
DVD-RAM
In addition to this Software and User ’Gs uide CD, your option package includes the following:
v ThinkPad DVD Ultrabay Slim Burner
v Carrying case
v Quick Reference Guide
v Laser Safety Guide
Contact your place of purchase if an item is missing or damaged. Be sure to retain your proof of
purchase. It might be required to receive warranty service. See Appendix D, “Service and Support,” on
page 21 for technical support information.
Software description
Your DVD Burner User's Guide and Software CD contains the following software:
v Intervideo WinDVD Creator
This software enables you to record video files to DVD-RW, DVD-R, DVD+RW, and DVD+R media
that can be played in most stand-alone DVD players. You can also use this software to edit and modify
your own video assets prior to recording. DVD-RAM recording is also supported. If you have an
analog, USB, or IEEE 1394 capture device installed in your computer, you can use this software to
record video from a camera.
© Lenovo 2007. Portions © IBM Corp. 2005.
1
v Drag-to-Disc (DLA)
This software enables you to write directly to CD and DVD media using the drive letter as you would
if you were writing to a diskette. You can also format DVD-RAM, DVD-RW, DVD-R, DVD-R DL,
DVD+R DL, DVD+RW, and DVD+R media. With DLA, you can drag-and-drop files, create new
directories, or save files from almost any application directly to your DVD Burner. Drag-to-disc is
installed as part of the Multimedia Center for Think Offerings.
v UDF reader
This software enables you to install software for reading DVD-RAM, DVD-RW, DVD+RW, DVD-R DL,
DVD+R DL, and CD-RW media on other computers with DVD drives.
v Multimedia Center for Think Offerings
This software enables you to copy CDs, create audio CDs, create MP3 CDs, and author data CDs. You
can also use Multimedia Center for Think Offerings to write data to DVD-RAM, DVD-RW, DVD-R,
DVD-R DL, DVD+RW, DVD+R DL, and DVD+R discs for use in other computers or compatible
consumer electronics products. You can also create bootable CDs and save CD images for later
recording. With the Express Labeller that is included in the Multimedia Center for Think Offerings, you
can print paper labels or label LightScribe discs.
v Intervideo WinDVD
This software enables you to play back DVD videos on your computer or to play video files from your
hard disk drive.
Note: Some graphics adapters such as the FIREGL, Intergraph, and 3dLabs, do not support DVD video
playback.
Installation requirements
To install the drive, your ThinkPad notebook computer must contain the following requirements:
v A ThinkPad system with an Ultrabay Slim Drive Bay or Ultrabay Enhanced Bay
v A ThinkPad X4 Ultrabase Dock or Dock II
v Microsoft® Windows® Vista™, Microsoft Windows XP, or Microsoft Windows 2000 operating system
Note: Lenovo offers limited support for computers with Microsoft Windows 95, Windows 98, or
Microsoft Windows Millennium Edition (Me) desktop operating systems.
Installing the drive
Your ThinkPad computer includes a help system, Access ThinkPad, that provides drive installation
instructions specific to your computer. To correctly install the drive into the Ultrabay Slim Drive Bay or
Ultrabay Enhanced Bay, use the instructions given in the Access ThinkPad help system.
2
ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Locating the drive controls
The following diagram shows the location of the controls on the front of the drive.
ꢀ1ꢁ Power light: This light is visible when the drive is in use.
ꢀ2ꢁ Eject button: Press this button to eject a DVD or CD.
ꢀ3ꢁ Manual eject hole: Use this emergency release to eject a DVD or CD when the Eject button does not
work. For more information on manually ejecting a DVD or CD, see “Manually ejecting a disc” on page
Chapter 1. About the drive
3
4
ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Chapter 2. Using the drive
This section provides information on how to handle, load, and care for DVDs and CDs, and how to care
for your drive.
Before you begin
For best results, review the following guidelines before using the drive:
v Do not move your ThinkPad computer while formatting or writing a disc as this might cause data
errors. Also, minimize typing while formatting or writing to a disc, as this might also cause data errors.
v Keep the ThinkPad computer on a flat surface when writing to a disc.
v Make sure the ThinkPad computer is plugged into an ac outlet when using the drive. The disc might
be damaged if the battery runs out while writing to a disc.
v Turn screensavers off. Using a screensaver might interrupt the formatting and writing process.
v Do not put your ThinkPad computer into hibernation or suspend mode while writing to a disc.
Note: The read and write results of the drive depend upon the quality and characteristics of the DVD or
CD media used.
Caring for the drive
To protect your drive during operation, observe these precautions:
v Remove the disc from the drive before moving the drive.
v Do not insert foreign objects into the drive.
v Do not stack objects on the drive.
v Do not remove the drive cover or attempt to service the drive.
v Do not operate the drive under any of these conditions:
– High temperature, high humidity, or direct sunlight
– Excessive vibration, sudden shock, or inclined surface
– Excessive dust
Loading a disc
1. Press the Eject button. The tray slides out of the drive.
2. Place a disc in the tray with the label facing up.
3. Close the tray by gently pushing the tray in until it latches.
© Lenovo 2007. Portions © IBM Corp. 2005.
5
Attention: Do not use force or insert foreign objects to open the tray. If your tray does not open when you press the
Securing a disc in a vertically mounted drive
The drive has four retainers molded into the loading tray for vertical mounting operation. To insert a
disc, place it in the lower two retainers before closing the tray. To remove a disc, open the tray and lift
the disc from the two lower retainers.
Manually ejecting a disc
If you press the Eject button and the tray does not slide out, turn off the computer and straighten a large
paper clip to form a tool, as shown in the illustration. The straightened end must extend at least 45 mm
(1.8 in.). Insert the extended end into the manual-eject hole on the front of the drive. Push the paper clip
until the tray opens. Gently pull out the tray until you can remove the disc.
45 mm
1.8 in
Using media
This section contains information on using media.
Handling and caring for a disc
Carefully handle and clean discs, especially writable media types such as CD-R and CD-RW discs, so that
they remain readable. You can prolong the life of your discs by using these precautions:
v Always store discs in their original packaging.
v Always store discs out of direct sunlight.
v Always store discs away from direct heat sources.
v Remove discs from the computer when not in use.
v Check discs for cracks BEFORE each use.
IMPORTANT: Do not use discs that are cracked.
v Do not force discs into the computer or packaging.
v Do not bend or flex discs.
v Do not use commercial cleaners to clean discs.
v Do not write on the surface of discs.
v Handle discs by the edges or the center hole.
v Do not touch the surface of discs.
v To remove dust or fingerprints, wipe discs from the center to the edge with a soft, lint-free cloth.
Attention: Wiping a disc using a circular motion can cause data loss.
6
ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Your drive can use many different types of media. Not all media is used in the same ways. The following
sections describe what you can do with the different media types.
Using DVD-RAM media
DVD-RAM media is available in bare-disc or cartridge form. To use cartridge media in your drive, you
must first remove the disc from the cartridge.
Removing the disc from the cartridge
2a
3a
Using the tip of a ball point pen, push and break the lock pin tab ꢀ1ꢁ. To remove the disc, use a ball
point pen to push down on the cartridge lid lock ꢀ2ꢁ and pull the cartridge lid out ꢀ3ꢁ. When the
cartridge lid is open, the disc can be removed.
Note: The cartridge lid lock and the cartridge lid tab are located on the side of some cartridges, as shown
in ꢀ2aꢁand ꢀ3aꢁabove.
Attention: Do not touch the recording area of the disc when handling bare media.
Returning the disc to the cartridge
Chapter 2. Using the drive
7
To return the disc to the cartridge, align the label side of the disc ꢀ1ꢁwith the DVD-RAM cartridge label
side. Insert the disc and close the cartridge lid ꢀ2ꢁ. A clicking sound will occur when the lid closed.
Precautions for handling
Be careful when handling the removed disc. Debris, dust particles, fingerprints, smears, or scratches may
impair recording and playback of the media. To clean dust or other debris, use a CD Cleaning Kit. Use a
soft, dry cloth to clean the disc. Do not use solvents to clean the disc surface. When labeling a disc, write
only on the printed label side or the cartridge using a soft felt-tip marker. Keep out of direct sunlight,
high temperatures, and humidity. Do not attach labels to either side of the disc.
Using single and double-sided DVD-RAM media
DVD-RAM media is available in single-sided and double-sided versions.
The 2.6 GB and 4.7 GB versions are single-sided. The 9.4 GB versions are double-sided. To access the data
on both sides of the media, you must remove the media from the drive, turn it over, and re-insert it into
the drive.
Using CDs and DVDs
Complete these steps to read a data disc:
1. Turn on the computer.
2. Press the Open/Close button on the front of the drive.
3. Insert a disc or cartridge in the tray with the label facing up.
4. Close the tray by pressing the Open/Close button or by gently pushing in the loading tray.
Attention: Do not use force or insert foreign objects to open the loading tray.
5. Wait for the drive busy indicator to turn off; then double-click My Computer.
6. Double-click the CD-ROM or DVD-RAM/DVD-R/DVD-RW icon.
Using CD-Rs and CD-RWs
The drive can write to both CD-R and CD-RW discs. CD-R discs cannot be erased, but can be used with
standard CD-ROM drives and CD players.
You can use CD-R discs to record audio tracks, store data, archive files, and copy files from another CD.
CD-RW discs can be erased and rewritten, but can be used only with newer CD-RW-compatible CD-ROM
and DVD-ROM drives. You can use CD-RW discs to back up, store, and update files or to copy files from
another CD.
Notes:
1. CD-R discs are playable on audio CD players. CD-RW discs are not playable on most audio CD
players.
2. The software included with this drive does not enable the drive CD-recording capabilities with DOS,
Windows 3.x, or OS/2® operating systems.
For more information on using the software, refer to “Using Drag-to-Disc (DLA)” on page 10 and “Using
Using DVD-Rs and DVD-RWs
The drive can write to both DVD-R and DVD-RW discs. DVD-R discs cannot be erased, but can be used
with standard DVD-ROM drives and DVD players.
You can use DVD-R discs to record audio tracks, store data, archive files, and copy files from another
DVD.
8
ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
DVD-RW discs can be erased and rewritten, but can be used only with newer MR- and
DVD-RW-compatible DVD-ROM drives. You can use DVD-RW discs to back up, store, and update files or
to copy files from another DVD.
For more information on using the software, refer to the Multimedia Center for Think Offerings and DLA
help information on the Software and User’s Guide Super CD.
Installing software
After you connect the drive to the computer, you can install application software from the User’s Guide
and Software CD. Complete these steps to install application software:
1. Insert the User’s Guide and Software CD into the drive.
2. The CD should automatically start. If it does, proceed to Step 5.
3. If the CD does not automatically start, click Start, then Run.
4. In the Run box type e:\launch.bat where e is the drive letter of the ThinkPad DVD Ultrabay Slim
Burner.
5. If you get a warning from Internet Explorer about malicious scripts, right-click on the warning bar,
and select Allow Blocked Content.
6. Select Software from the left-hand navigator bar.
7. Check the boxes by the software applications that you wish to install.
8. Click Go. The software you selected will install silently.
9. Restart the computer after the completion message.
Note: If the software fails to install silently, you can select interactive installs of individual packages from
the bottom line of the installer page.
Using Intervideo WinDVD Player software
This section describes how to use and customize the Intervideo WinDVD Player. You can find current
information on Intervideo WinDVD Player in the readme file on the User’s Guide and Software CD.
Before using the software
WinDVD requires a compatible video device driver and IDE bus mastering in order to work. See
enabling DMA bus mastering and for locating video device drivers.
Using WinDVD
When you insert a DVD Video disc into the drive, the Intervideo WinDVD Player will automatically start
and begin to play the video disc. If the DVD disc contains both video and program content, the program
content will automatically play.
To view the video content of a video/program DVD disc, go to the Start menu, launch WinDVD, and
click Play.
With Microsoft Windows XP, you can also play DVD Video content by using the Windows Media Player
application.
Changing the DVD region code
Regionalization and Copy Protection (the DVD region code) uses the content scramble system (CSS)
standard to prevent unauthorized duplication of the intellectual property rights distributed on DVDs. It
was originally requested by the Motion Picture Association of America (MPAA) to address video piracy,
but is applicable to any content. CSS works by inhibiting the transmission of unencrypted data without
proper authorization. Playback systems must license CSS to decode the encrypted data.
Chapter 2. Using the drive
9
The CSS specification divides the world into seven unique regions. Content designated for one region
cannot be read by playback systems in another region. While CSS is used to prevent digital copies of the
DVD content, another technology devised by Macrovision is used to prevent analog copies of the DVD
content. The Macrovision standard is a scrambling system widely used by the movie industry to prevent
unauthorized duplication of video content using commercial VCRs. DVD playback systems must support
both CSS and Macrovision copy protection standards.
The first time that you insert a DVD Video disc into the drive, you will be prompted to set the region. If
you relocate to a different region of the world, you can use the DVD Player software to change the region
code.
Note: You can change the DVD region code only five times. After you make five region code changes,
the drive can play only MPEG-2 video titles that are associated with the fifth region code that you
set.
To change the region code, complete these steps:
1. Turn on your computer and start your operating system.
2. Click Start.
3. Select Programs.
4. Click Intervideo WinDVD.
5. Click Intervideo WinDVD.
6. Click the Properties icon to open the Properties window.
7. Click the General Properties tab.
8. Insert a single region DVD of the new region.
9. Select the correct region code for your country.
10. Click OK.
Using Drag-to-Disc (DLA)
Drag-to-Disc (DLA) is provided so that you can write data to DVD-RAM, DVD-RW, DVD-R, DVD+RW,
DVD+R, CD-R, and CD-RW media. DVD-RAM, DVD-RW, DVD+RW, and CD-RW media can be written
to many times, while DVD-R, DVD+R, and CD-R media can only be formatted and written to once.
To format and write to DVD-RAM, DVD-RW, DVD-R, DVD+RW, DVD+R, CD-R, or CD-RW media:
1. Insert a disc into the drive.
2. Double-click My Computer. Right-click the CD/DVD Burner drive letter.
3. Click Format. Formatting a DVD can take up to 90 minutes.
4. After formatting is complete, you can drag and drop files to the CD/DVD Burner drive icon, or you
can move files in Windows Explorer.
To make CD-R and DVD-R media compatible in other computers, complete these steps:
1. Double-click My Computer. Right-click the CD/DVD Burner drive letter.
2. Click Make Compatible.
To use UDF formatted DVD-RAM, DVD-RW, DVD+RW, or CD-RW media in other computers, a UDF
reader is included on the User’s Guide and Software CD.
To use the UDF reader, complete these steps:
1. Insert the User’s Guide and Software CD into the CD or DVD drive of the computer you want to use
the UDF formatted discs with. The CD will Autoplay
2. Select Software from the navigation menu.
3. Select the proper UDF reader for your operating system. Both 32 and 64 bit versions are included in
the installer list.
Notes:
1. The UDF reader is only needed on systems that do not have another DLA program installed.
10 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
2. If the ″use with DLA″ menu item is not selected in Windows XP, Windows XP CD recording will be
used.
Using Multimedia Center for Think Offerings application
You can use the Multimedia Center for Think Offerings application to burn data, audio, video, CD and
DVDs. You can also access tools and utilities for working with rewritable media. The Multimedia Center
for Think Offerings application also has projects to manage disk images and create file backups.
To start the Multimedia Center for Think Offerings application in Windows XP, click Start -> All
Programs -> Multimedia Center for Think Offerings -> Multimedia Center Home.
When the Multimedia Center first starts, you are taken to a Quick Links page. This page shows the four
most used tasks for your convenience. To make an Audio or Data disc, select the appropriate tab and
select the task you want to perform. To copy a disc, make a disc image, or burn a previously saved
image, select the Copy tab. To use Drag-to-disc (DLA), select the Data tab. To erase a rewritable disc,
select the Tools tab.
You can access the Data, Audio, and Copy tabs directly from the Start menu as RecordNow Copy,
RecordNow Data, and RecordNow Audio by clicking Start -> All Programs -> Multimedia Center for
Think Offerings.
To make a bootable CD or DVD, begin a data project and click the bootable CD button in the upper right
corner of the project window. You will be prompted to select a boot image from your hard disc or make a
boot image from a floppy disc.
For detailed instructions on using the Multimedia Center, consult the on-line helps.
Copying and imaging discs
You can use the Multimedia Center for Think Offerings application to make copies and save images of
your CDs. You can also create CDs from images that you have previously saved on your hard disc. The
Multimedia Center can only save images in ISO and GI formats. ISO formats can only be used for data
CDs. All other disc formats require GI images.
Saved CD images can be as large as 730 MB, and saved DVD images can be as large as 8.6 GB. Ensure
that you have adequate hard drive disk space before proceeding.
To make a CD image, complete these steps:
1. Start the Multimedia Center for Think Offerings application.
2. Click the Copy page.
3. Click the task Save Image to Hard disk.
4. The application creates a random name for you. Rename the image file.
5. Insert the disc that you are imaging.
6. Click the Record button.
Notes:
1. DLA CDs cannot be saved as image files.
2. Copy protected commercial CDs cannot be imaged.
To burn a previously saved image, complete these steps:
1. Start the Multimedia Center for Think Offerings application.
2. Click the Copy page.
3. Click the task Burn Image to CD or DVD.
4. Use the Browse button to navigate to the image that you want to burn.
5. Insert a blank or erasable disc.
6. Click the Record button.
Chapter 2. Using the drive 11
To copy a disc, complete these steps:
1. Start the Multimedia Center for Think Offerings application.
2. Click the Copy page.
3. Click the task Copy a disc.
4. Insert the disc that you want to copy.
5. Click the Record button.
6. When prompted, insert the target disc.
Notes:
1. Copy protected CDs cannot be copied.
2. Copying or imaging discs without the copyright owner’s permission can result in legal penalties. For
more information on copyright law, consult your legal advisor.
Using Intervideo WinDVD Creator
With Intervideo WinDVD Creator, you can capture, edit, and record video and audio files. You can also
use Intervideo WinDVD Creator to create and record DVD videos using your own video and audio files.
For more detailed information on Intervideo’s WinDVD Creator features, refer to the online WinDVD
Creator User’s Guide on the User’s Guide and Software CD.
The main function areas within the WinDVD Creator main window are Capture, Edit, Author, and Make
Movie. From these functions, you can import and edit your own video and audio files; then save them
into any of the following supported formats: MPEG-1, MPEG-2, ASF, WMV, and AVI.
When you have prepared your video and audio files, by going through the Capture and Edit steps, you
can then add a customized menu from within the Author function. You can import your own still images
to use as menu backgrounds or select one of the sample images. When your movie is ready, proceed to
Make Movie where you can select the output format and video standard used in creating your movie.
Write your movie to disc or save it to the hard disk drive for writing later. If you use WinDVD Creator
Plus to create a DVD image on your hard disk drive, you can select Load Image to Burn from the Project
menu.
WinDVD Creator also offers the capability to record video directly to DVD-recordable media using Disk
Manager without using any additional space on the hard disk drive. With Disk Manager, you can capture
new video or use video files that you already have, and then finish your movie by creating a customized
menu. Your movie can be created in +VR or -VR video formats. Through Disk Manager, you can edit
your movie at any time, adding or deleting video segments or changing your customized menu.
Note: +/-VR formatted disks have limited compatibility in older set-top DVD players.
12 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Appendix A. Customizing the device driver configuration
settings
Microsoft Windows Me and Windows 2000 Professional have two device-driver configuration parameters:
Auto Insert Notify and DMA.
The Auto Insert Notify parameter enables the computer to start playing or accessing the disc
automatically after being inserted in the drive. The DMA parameter improves the computer performance
by having the computer DMA controller handle data transfers from the CD to memory, freeing the
computer’s microprocessor to perform more important tasks. For example, activating DMA might make
movies and games run more smoothly because the microprocessor is allocating more processing time to
video.
Enabling DMA for Windows Me
To change the DMA parameter settings in Windows Me, complete these steps
1. Click Start.
2. Click Settings.
3. Click Control Panel.
4. Click View all control panel options.
5. Double-click System.
6. Click the Device Manager tab.
7. Double-click CD-ROM.
8. Click on the drive that you want to modify.
9. Click the Settings tab.
10. Click to select the DMA check box.
11. Click OK.
Enabling DMA for Windows 2000 Professional
To change the parameter settings for Windows 2000 Professional, complete these steps
1. Click Start.
2. Click Settings.
3. Click Control Panel.
4. Double-click System.
5. Click the Hardware tab.
6. Click the Device Manager button.
7. Click the IDE ATA/ATAPI controller to expand the tree.
8. Click the device that corresponds to the controller where your CD/DVD Burner is located (Primary
IDE or Secondary IDE).
9. Click the Advanced Settings tab.
10. Select the Transfer Mode pull-down menu and select DMA if available.
11. Click OK.
12. Click Close to close the System Properties window. A message is displayed informing you that the
system settings have changed.
13. Click OK to restart your computer.
© Lenovo 2007. Portions © IBM Corp. 2005.
13
Enabling DMA for Windows XP
To change the DMA parameter setting from the Windows XP desktop, complete these steps
1. Click Start.
2. Click Control Panel.
3. Click Switch to classic view.
4. Double-click System.
5. Click the Hardware tab.
6. Click the Device Manager button.
7. Click the IDE ATA/ATAPI controller to expand the tree.
8. Double-click on the controller where your CD/DVD Burner is located (Primary IDE or Secondary
IDE).
9. Click the Advanced Settings tab.
10. Select the appropriate Transfer Mode pull-down that corresponds to the CD/DVD Burner location,
(Device 0 for Master, Device 1 for Slave).
11. Select DMA if it is available.
12. Click OK.
Enabling digital audio extraction
Your system must be properly configured to play back digital audio from this drive. There are two
setting that must be configured. One setting is in the device properties, and a second setting is in
Windows Media Player.
To set the device properties, complete these steps:
1. Right-click on My Computer, and select Properties.
2. Select Device Manager from the Hardware tab. In Windows Me, the Hardware tab shows the Device
Manager directly without clicking the button, as shown in the figure below.
14 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
3. In the Device Manager tab, open the ’+’ for DVD/CD-ROM drives, right-click on your drive, and
select Properties.
4. Select the Properties tab and check the Enable Digital Audio checkbox, as shown in the figure below.
Appendix A. Customizing the device driver configuration settings 15
To enable Digital Audio Playback in Windows Media Player, complete these steps:
1. Open Windows Media Player.
2. Select Tools→Options... from the Media Player menu.
3. Select the CD Audio tab and check the Digital Playback box, as shown in the figure below.
16 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Appendix B. Troubleshooting
Computer problems can be caused by hardware, software, or user error. The information in this section
might be useful to help you solve problems or to gather helpful information you can pass on to a service
technician. You might also need to refer to your computer, operating-system, or sound-adapter
publications.
Review the following list for any problem descriptions that might fit your situation.
You cannot create a multi-session disc.
Be sure that there is enough space left on the disc for another session. Writing a session requires lead-in
and lead-out space (about 15 MB) in addition to the data that is recorded.
You cannot successfully write to a CD-R, CD-RW, DVD-R, DVD-RW, or DVD-RAM disc.
Complete these steps:
1. Verify that the process is not being interrupted by a screen saver, an antivirus program, an Internet or
e-mail program, or other software. Disable the functions that might interrupt the write operation.
2. Verify that the hard disk has been defragmented.
3. Consult the hard disk drive manufacturer or vendor if an older hard disk drive is conducting a
thermal recalibration during a write operation.
4. Replace the CD if it is bad or scratched.
5. Disable the Windows Auto Insert Notify function on your CD-ROM and CD-RW drives.
You cannot eject a CD or DVD disc.
Complete these steps after ensuring that the drive is not in the process of writing to a disc:
1. Eject the CD through software.
2. Use the Eject button.
3. Turn off the computer. Wait 45 seconds; then turn on the computer and try using the Eject button
again.
You cannot read from the CD or DVD disc after successfully writing to it.
Complete these steps:
1. If you can read the CD or DVD Disc in another CD or DVD player or you can see previous sessions,
the directory information might be damaged on the volume, making it unreadable. To get ideas for
troubleshooting, check the documentation that comes with the software.
2. You might have a damaged CD-R, CD-RW, DVD-R, DVD-RW, or DVD-RAM disc. Try a new disc or
another brand of CD or DVD disc.
3. If you can read from a CD-RW, DVD-RW, or DVD-RAM disc in the writing drive, but not in another
CD drive, be sure that a UDF Reader program is installed in the computer.
4. Avoid writing at the slower 1X speed unless required by your computer.
You suspended your system and DVD playback will not resume.
This is normal with some device drivers. Playback will continue after you exit and restart WinDVD.
Unable to Create Overlay Window message appears when you use WinDVD with Windows 2000.
© Lenovo 2007. Portions © IBM Corp. 2005.
17
Complete these steps:
1. Your video device driver needs an update to enable overlay support. Contact the manufacturer of
your video adapter or your computer for updates.
2. The resolution of your screen might be too high. Try setting the resolution to 800 x 600 x 16 bpp at 60
Hz.
DVD movies do not start automatically when inserted into the drive.
Complete these steps:
1. Under Windows 2000, DVDs that contain both programs and DVD Video content will autoplay the
program content. To view the video content, start WinDVD manually.
2. Under Windows XP or Windows Vista, you have chosen to always start data discs in file only mode.
Refer to the Windows online manual for information on restoring program defaults.
Video appears to be choppy or is dropping frames.
Complete these steps:
1. Ensure that DMA is enabled on for your computer hard disk drive controller.
2. The resolution of your screen might be too high. Try setting the resolution to 800 x 600 x 16 bpp at 60
Hz.
3. If your computer microprocessor has less power than a Pentium II 450 microprocessor, some jerkiness
is normal on certain DVDs.
DVD-R DL media cannot be read in other computers after burning.
Complete these steps:
1. Check with your manufacturer to be sure that the drive can read DVD+R DL and DVD-R DL media.
2. Complete these steps to enable IMAPI for Windows XP:
a. Double-click My Computer.
b. Right-click on the DVD reader drive.
c. Select Properties.
d. Click Recording.
e. Check the Enable CD Recording on this drive checkbox.
f. Click Apply.
3. Try installing the UDF reader in the other computer.
A direct-to-disc media occurred and you cannot eject the disc or shut down the computer.
Complete these steps:
1. Wait a few minutes until the drive light flashes and goes out, then try again.
2. Emergency eject the disc. Open Task Manager and end the task DLAWCRTL.EXE.
3. Turn off the computer.
18 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Appendix C. Product specifications
This appendix includes the following information:
v Physical specifications
v Power requirements
v Environmental requirements
v Read speeds
v Write speeds
Physical specifications
The physical specifications1 of the drive are listed in the following table.
Physical specification
Height
Width
Length
Weight
9.5 mm (0.4 in.)
128 mm (5 in.)
129 mm (5.09 in.)
155 g (0.38 lb)
Power requirements
The following table lists the power specifications by voltage level for the drive. The power specifications
are measured at the drive power connector and are nominal values.
Power specifications
Voltage
Average
Maximum
At voltage
DC 5V
1100 mA
1800 mA
Environmental requirements
Specification
Operational
Non-operational
Temperature (non-condensing)
+5° C to +50° C
-20° C to +60° C
(+41° F to +122° F)
10% to 80%
(-4° F to +140° F)
5% to 90%
Relative humidity (non-condensing)
Read speeds
Media
Read Speed
24X Max.
24X Max.
24X Max.
24X Max.
8X Max.
CD-R
CD-RW
High Speed CD-RW
Ultra Speed CD-RW
DVD-R
DVD+R
8X Max.
1. Product-description data represents Lenovo’s design objectives and is provided for comparative purposes; actual results might
vary based on a variety of factors. This product data does not constitute a warranty. Data is subject to change without notice.
© Lenovo 2007. Portions © IBM Corp. 2005.
19
DVD-R Dual layer
DVD+R Double layer
DVD-RW
6X Max.
6X Max.
8X Max.
8X Max.
5X Max.
DVD+RW
DVD-RAM
Write speeds
Media
Write speed
24X Max.
16X Max.
8X Max.
8X Max.
4X Max.
4X Max.
6X Max.
6X Max.
5X Max.
CD-R
CD-RW
DVD-R
DVD+R
DVD-R Dual layer
DVD+R Double layer
DVD-RW
DVD+RW
DVD-RAM
20 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Appendix D. Service and Support
The following information describes the technical support that is available for your product, during the
warranty period or throughout the life of your product. Refer to the Lenovo Limited Warranty for a full
explanation of Lenovo warranty terms.
Registering your option
Register to receive product service and support updates, as well as free and discounted computer
accessories and content.
Online technical support
support.
Product replacement assistance or exchange of defective components also is available during the
warranty period. A Lenovo technical support representative can help you determine the best alternative.
In addition, if your Lenovo option is installed into a Lenovo computer, the option takes on the warranty
of the computer in which it is installed. For many Lenovo computers, this can entitle the Lenovo option
for warranty service up to three years.
Telephone technical support
Installation and configuration support through the Customer Support Center will be available until 90
days after the option has been withdrawn from marketing. After that time, the support is cancelled, or
made available for a fee, at Lenovo’s discretion. Additional support is also available for a nominal fee.
Before contacting a Lenovo technical support representative, please have the following information as
possible: option name and number, proof of purchase, computer manufacturer, model, serial number and
manual, the exact wording of any error message, description of the problem, and the hardware and
software configuration information for your system.
Your technical support representative might want to walk you through the problem while you are at your
computer during the call.
© Lenovo 2007. Portions © IBM Corp. 2005.
21
22 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Appendix E. Lenovo Limited Warranty
L505-0010-00 09/2006
This Lenovo Limited Warranty applies only to Lenovo hardware products you purchased for your own
use and not for resale. This warranty may sometimes be referred to as the ″Statement of Limited
Warranty″ (SOLW) in other documents from Lenovo.
What this Warranty Covers
Lenovo warrants that each hardware product is free from defects in materials and workmanship under
normal use during the warranty period. The warranty period for the product starts on the original date
of purchase specified on your invoice unless Lenovo informs you otherwise in writing. The warranty
period and type of warranty service that apply to your product are designated below under the section
titled ″Warranty Information.″
THIS WARRANTY IS YOUR EXCLUSIVE WARRANTY AND REPLACES ALL OTHER
WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. SOME STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION
OF EXPRESS OR IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO
YOU. IN THAT EVENT, SUCH WARRANTIES APPLY ONLY TO THE EXTENT REQUIRED BY LAW
AND ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES APPLY
AFTER THAT PERIOD. SOME STATES OR JURISDICTIONS DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION ON DURATION
MAY NOT APPLY TO YOU.
How to Obtain Warranty Service
If the product does not function as warranted during the warranty period, you may obtain warranty
service by contacting Lenovo or an approved service provider. Each of them is referred to as a ″Service
support/phone.
Warranty service may not be available in all locations and may differ from location to location. Charges
may apply outside a Service Provider’s normal service area. Contact a local Service Provider for
location-specific information.
What Your Service Provider Will Do to Correct Problems
When you contact a Service Provider, you must follow the problem determination and resolution
procedures specified.
Your Service Provider will attempt to diagnose and resolve your problem over the telephone or through
remote assistance. Your Service Provider may direct you to download and install designated software
updates.
Some problems can be resolved with a replacement part that you install yourself (such as keyboard,
mouse, speaker, memory, hard disk drive, or port replicator), called a ″Customer Replaceable Unit″ or
″CRU.″ If so, your Service Provider will ship the CRU to you for you to install.
© Lenovo 2007. Portions © IBM Corp. 2005.
23
If your problem cannot be resolved over the telephone or remotely, through your application of software
updates, or with a CRU, your Service Provider will arrange for service under the type of warranty service
designated for the product under the section titled ″Warranty Information.″
If your Service Provider determines that it is unable to repair your product, your Service Provider will
replace it with one that is at least functionally equivalent.
If your Service Provider determines that it is unable to either repair or replace your product, your sole
remedy is to return the product to your place of purchase or to Lenovo and your purchase price will be
refunded.
Exchange of a Product or Part
When the warranty service involves the exchange of a product or part, the item your Service Provider
replaces becomes Lenovo’s property and the replacement becomes yours. All removed items must be
genuine and unaltered. The replacement may not be new, but will be in good working order and at least
functionally equivalent to the item replaced. The replacement assumes the warranty status of the replaced
item.
Before your Service Provider exchanges a product or part, you agree to:
1. remove all features, parts, options, alterations, and attachments not under warranty service;
2. ensure that the product is free of any legal obligations or restrictions that prevent its exchange; and
3. obtain authorization from the owner to have your Service Provider service a product that you do not
own.
Your Additional Responsibilities
Where applicable, before service is provided, you agree to:
1. follow the service request procedures that your Service Provider specifies;
2. backup or secure all programs and data contained in the product;
3. provide your Service Provider with all system keys or passwords and sufficient, free, and safe access
to your facilities to permit the terms of this warranty to be fulfilled; and
4. ensure that all information about identified or identifiable individuals (″Personal Data″) is deleted
from the product or that, with respect to any remaining Personal Data you did not delete, you are in
compliance with all applicable laws.
Use of Personal Information
If you obtain service under this warranty, Lenovo will store, use, and process information about your
warranty issue and your contact information, including name, phone numbers, address, and e-mail
address. Lenovo will use this information to perform service under this warranty and to improve our
business relationship with you, such as to conduct internal reviews of the efficiency of the warranty
service we provide to you. We may contact you to inquire about your satisfaction regarding our warranty
service or to notify you about any product recalls or safety issues. In accomplishing these purposes, we
may transfer your information to any country where we do business and may provide it to entities acting
on our behalf. We also may disclose it where required by law or legal authorities to do so.
What this Warranty Does not Cover
This warranty does not cover the following:
v uninterrupted or error-free operation of a product;
v loss of, or damage to, your data;
v any software programs, whether provided with the product or installed subsequently;
v failure or damage resulting from misuse, accident, modification, unsuitable physical or operating
environment, natural disasters, power surges, or improper maintenance by you;
24 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
v any third party products, including those that Lenovo may procure and provide with or integrate into
the Lenovo product at your request; and
v any technical or other support, such as assistance with ″how-to″ questions and those regarding product
set-up and installation.
This warranty is voided by removal or alteration of identification labels on the product or its parts.
Limitation of Liability
Lenovo is responsible for loss of, or damage to, your product only while it is 1) in your Service
Provider’s possession or 2) in transit in those cases in which the Service Provider is responsible for the
transportation.
Neither Lenovo nor your Service Provider is responsible for any of your data including confidential,
proprietary, or personal data contained in a product. You should remove and/or backup all such
information from the product prior to its service or return.
Circumstances may arise where, because of a default on Lenovo’s part or other liability, you may be
entitled to recover damages from Lenovo. In each such instance, regardless of the basis on which you are
entitled to claim damages from Lenovo (including fundamental breach, negligence, misrepresentation, or
other contract or tort claim), except and to the extent that liability cannot be waived or limited by
applicable laws, Lenovo is liable for no more than the amount of actual direct damages suffered by you,
up to the amount you paid for the product. This limit does not apply to damages for bodily injury
(including death) and damage to real property and tangible personal property for which Lenovo is
required by law to be liable.
This limit also applies to Lenovo’s suppliers, resellers, and your Service Provider. It is the maximum for
which Lenovo, its suppliers, resellers, and your Service Provider are collectively responsible.
UNDER NO CIRCUMSTANCES IS LENOVO, ITS SUPPLIERS, RESELLERS, OR SERVICE
PROVIDERS LIABLE FOR ANY OF THE FOLLOWING EVEN IF INFORMED OF THEIR
POSSIBILITY: 1) THIRD PARTY CLAIMS AGAINST YOU FOR DAMAGES; 2) LOSS OF, OR
DAMAGE TO, YOUR DATA; OR 3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR
ANY ECONOMIC CONSEQUENTIAL DAMAGES, INCLUDING LOST PROFITS, BUSINESS
REVENUE, GOODWILL, OR ANTICIPATED SAVINGS. SOME STATES OR JURISDICTIONS DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
Dispute Resolution
If you acquired the product in Cambodia, Indonesia, Philippines, Vietnam or Sri Lanka, disputes
arising out of or in connection with this warranty shall be finally settled by arbitration held in Singapore
and this warranty shall be governed, construed and enforced in accordance with the laws of Singapore,
without regard to conflict of laws. If you acquired the product in India, disputes arising out of or in
connection with this warranty shall be finally settled by arbitration held in Bangalore, India. Arbitration
in Singapore shall be held in accordance with the Arbitration Rules of Singapore International Arbitration
Center (″SIAC Rules″) then in effect. Arbitration in India shall be held in accordance with the laws of
India then in effect. The arbitration award shall be final and binding for the parties without appeal and
shall be in writing and set forth the findings of fact and the conclusions of law. All arbitration
proceedings shall be conducted, including all documents presented in such proceedings, in the English
language, and the English language version of this warranty prevails over any other language version in
such proceedings.
Other Rights
Appendix E. Lenovo Limited Warranty 25
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE OR JURISDISCTION TO JURISDICTION. YOU ALSO MAY
HAVE OTHER RIGHTS UNDER APPLICABLE LAW OR WRITTEN AGREEMENT WITH LENOVO.
NOTHING IN THIS WARRANTY AFFECTS STATUTORY RIGHTS, INCLUDING RIGHTS OF
CONSUMERS UNDER NATIONAL LEGISLATION GOVERNING THE SALE OF CONSUMER
GOODS THAT CANNOT BE WAIVED OR LIMITED BY CONTRACT.
European Economic Area (EEA)
Customers in the EEA may contact Lenovo at the following address: Lenovo Warranty & Service Quality
Dept., PO Box 19547, Inverkip Road, Greenock, Scotland PA16 9WX. Service under this warranty for
Lenovo hardware products purchased in EEA countries may be obtained in any EEA country in which
the product has been announced and made available by Lenovo.
This Lenovo Limited Warranty is available in other languages at www.lenovo.com/warranty.
Warranty information
Product or
Machine Type
Type of Warranty
Service
Country or Region of Purchase
Worldwide
Warranty Period
ThinkPad
DVD
1 year
1, 4
Ultrabay Slim
Burner
If required, your Service Provider will provide repair or exchange service depending on the type of
warranty service specified for your product and the available service. Scheduling of service will depend
upon the time of your call, parts availability, and other factors.
A warranty period of 1 year on parts and 1 year on labor means that Lenovo provides warranty service
during the first year of the warranty period (or a longer period as required by law).
Types of Warranty Service
1. Customer Replaceable Unit (″CRU″) Service
Under CRU Service, your Service Provider will ship CRUs to you for you to install. Most CRUs are easy
to install whereas others may require some technical skill and tools. CRU information and replacement
instructions are shipped with your product and are available from Lenovo at any time upon request. You
may request that a Service Provider install some CRUs under one of the other types of warranty service
designated for your product. Installation of external CRUs (such as mice, keyboards, or monitors) is your
responsibility. Lenovo specifies in the materials shipped with a replacement CRU whether the defective
CRU must be returned. When return is required, 1) return instructions, a prepaid return shipping label,
and a container are included with the replacement CRU, and 2) you may be charged for the replacement
CRU if your Service Provider does not receive the defective CRU within thirty (30) days of your receipt
of the replacement.
2. On-site Service
Under On-Site Service, your Service Provider will either repair or exchange the product at your location.
You must provide a suitable working area to allow disassembly and reassembly of the Lenovo product.
For some products, certain repairs may require your Service Provider to send the product to a designated
service center.
3. Courier or Depot Service
26 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Under Courier or Depot Service, your product will be repaired or exchanged at a designated service
center, with shipping arranged by your Service Provider. You are responsible for disconnecting the
product. A shipping container will be provided to you for you to return your product to a designated
service center. A courier will pick up your product and deliver it to the designated service center.
Following its repair or exchange, the service center will arrange the return delivery of the product to you.
4. Customer Carry-In or Mail-In Service
Under Customer Carry-In or Mail-In Service, your product will be repaired or exchanged at a designated
service center, with delivery or shipping arranged by you. You are responsible to deliver or mail, as your
Service Provider specifies, (prepaid unless specified otherwise) the product suitably packaged to a
designated location. After the product has been repaired or exchanged, it will be made available for your
collection. Failure to collect the product may result in your Service Provider disposing of the product as it
sees fit. For Mail-in Service, the product will be returned to you at Lenovo’s expense, unless your Service
Provider specifies otherwise.
Guarantee supplement for Mexico
This supplement is considered part of the Lenovo Limited Warranty and shall be effective solely and
exclusively for products distributed and commercialized within Territory of the Mexican United States. In
the event of a conflict, the terms of this supplement shall apply.
All software programs pre-loaded in the equipment shall only have a thirty- (30) day guarantee for
installation defects from the date of purchase. Lenovo is not responsible for the information in such
software programs and/or any additional software programs installed by you or installed after purchase
of the product.
Services not chargeable to the guarantee shall be charged to the final user, prior an authorization.
In the event that warranty repair is required please call the Customer Support Center at 001-866-434-2080,
where you will be directed to the nearest Authorized Service Center. Should no Authorized Service
Center exist in your city, location or within 70 kilometers of your city or location, the guarantee includes
any reasonable delivery charges related to the transportation of the product to our nearest Authorized
Service Center. Please call the nearest Authorized Service Center to obtain the necessary approvals or
information concerning the shipment of the product and the shipment address.
To obtain a list of Authorized Service Centers, please visit:
Manufactured by:
SCI Systems de México, S.A. de C.V.
Av. De la Solidaridad Iberoamericana No. 7020
Col. Club de Golf Atlas
El Salto, Jalisco, México
C.P. 45680,
Tel. 01-800-3676900
Marketing by:
Lenovo de México, Comercialización y
Servicios, S. A. de C. V.
Alfonso Nápoles Gándara No 3111
Parque Corporativo de Peña Blanca
Delegación Álvaro Obregón
Appendix E. Lenovo Limited Warranty 27
México, D.F., México
C.P. 01210,
Tel. 01-800-00-325-00
28 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Appendix F. Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries.
Consult your local Lenovo representative for information on the products and services currently available
in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply
that only that Lenovo product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any Lenovo intellectual property right may be used instead.
However, it is the user’s responsibility to evaluate and verify the operation of any other product,
program, or service.
Lenovo may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not give you any license to these patents. You can send
license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some
jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore,
this statement may not apply to you.
This information could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication.
Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in
this publication at any time without notice.
The products described in this document are not intended for use in implantation or other life support
applications where malfunction may result in injury or death to persons. The information contained in
this document does not affect or change Lenovo product specifications or warranties. Nothing in this
document shall operate as an express or implied license or indemnity under the intellectual property
rights of Lenovo or third parties. All information contained in this document was obtained in specific
environments and is presented as an illustration. The result obtained in other operating environments
may vary.
Lenovo may use or distribute any of the information you supply in any way it believes appropriate
without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not
in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part
of the materials for this Lenovo product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled environment. Therefore, the
result obtained in other operating environments may vary significantly. Some measurements may have
been made on development-level systems and there is no guarantee that these measurements will be the
same on generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.
© Lenovo 2007. Portions © IBM Corp. 2005.
29
Recycling information
Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their
equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist
equipment owners in recycling their IT products. Information on product recycling offerings can be found
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries, or both:
Lenovo
ThinkPad
Ultrabay
IBM is a trademark of International Business Machines Corporation in the United States, other countries,
or both and is used under license.
Microsoft, Windows, and Vista are trademarks of Microsoft Corporation in the United States, other
countries, or both.
Other company, product, or service names may be trademarks or service marks of others.
30 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Appendix G. Electronic emission notices
The following information refers to the ThinkPad DVD Ultrabay Slim Burner.
Federal Communications Commission (FCC) Declaration of Conformity
ThinkPad DVD Ultrabay Slim Burner - (41N5643)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
v
v
v
v
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult an authorized dealer or service representative for help.
Lenovo is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized
changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Responsible party:
Lenovo (United States) Incorporated
1009 Think Place - Building One
Morrisville, NC 27650
Phone Number: 919-294-5900
Industry Canada Class B emission compliance statement
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformité à la réglementation d’Industrie Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
EU-EMC Directive (89/336/EEC) as amended by Directive 93/86/EEC EN 55022 class B Statement of Compliance
Deutschsprachiger EU Hinweis:
Hinweis für Geräte der Klasse B EU-Richtlinie zur ElektromagnetischenVerträglichkeit Dieses Produkt entspricht den Schutzanforderungen der
EU-Richtlinie 89/336/EWG zur Angleichung der Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-Mitgliedsstaaten.
und hält die Grenzwerte der EN 55022 Klasse B ein.
Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu betreiben. Des Weiteren dürfen auch nur von
der Lenovo empfohlene Kabel angeschlossen werden. Lenovo übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das
Produkt ohne Zustimmung der Lenovo verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne Empfehlung der Lenovo
gesteckt/eingebaut werden.
Deutschland: Einhaltung des Gesetzes über die elektromagnetische Verträglichkeit von Geräten Dieses Produkt entspricht dem ″Gesetz über die
elektromagnetische Verträglichkeit von Geräten (EMVG)″. Dies ist die Umsetzung der EU-Richtlinie 89/336/EWG in der Bundesrepublik Deutschland.
Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit von Geräten (EMVG) vom 18. September 1998
(bzw. der EMC EG Richtlinie 89/336) für Geräte der Klasse B Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das
EG-Konformitätszeichen - CE - zu führen.
Verantwortlich für die Konformitätserklärung nach Paragraf 5 des EMVG ist die Lenovo (Deutschland) GmbH, Pascalstr. 100, D-70569 Stuttgart.
Informationen in Hinsicht EMVG Paragraf 4 Abs. (1) 4:
Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse B.
European Union - Compliance to the Electromagnetic Compatibility Directive
This product is in conformity with the protection requirements of EU Council Directive 89/336/ECC on the approximation of the laws of the Member
States relating to electromagnetic compatibility. Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from
a non-recommended modification of the product, including the fitting of option cards from other manufacturers.
This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to European Standard EN
55022. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with
licensed communication devices.
© Lenovo 2007. Portions © IBM Corp. 2005.
31
Avis de conformité à la directive de l’Union Européenne
Le présent produit satisfait aux exigences de protection énoncées dans la directive 89/336/CEE du Conseil concernant le rapprochement des
législations des Etats membres relatives à la compatibilité électromagnétique. Lenovo décline toute responsabilité en cas de non-respect de cette
directive résultant d’une modification non recommandée du produit, y compris l’ajout de cartes en option non Lenovo.
Ce produit respecte les limites des caractéristiques d’immunité des appareils de traitement de l’information définies par la classe B de la norme
européenne EN 55022 (CISPR 22). La conformité aux spécifications de la classe B offre une garantie acceptable contre les perturbations avec les
appareils de communication agréés, dans les zones résidentielles.
Unión Europea - Normativa EMC
Este producto satisface los requisitos de protección del Consejo de la UE, Directiva 89/336/CEE en lo que a la legislatura de los Estados Miembros
sobre compatibilidad electromagnética se refiere.
Lenovo no puede aceptar responsabilidad alguna si este producto deja de satisfacer dichos requisitos de protección como resultado de una
modificación no recomendada del producto, incluyendo el ajuste de tarjetas de opción que no sean Lenovo.
Este producto ha sido probado y satisface los límites para Equipos Informáticos Clase B de conformidad con el Estándar Europeo EN 55022. Los
límites para los equipos de Clase B se han establecido para entornos residenciales típicos a fin de proporcionar una protección razonable contra las
interferencias con dispositivos de comunicación licenciados.
Unione Europea - Directiva EMC (Conformidad électromagnética)
Questo prodotto è conforme alle normative di protezione ai sensi della Direttiva del Consiglio dell’Unione Europea 89/336/CEE sull’armonizzazione
legislativa degli stati membri in materia di compatibilità elettromagnetica.
Lenovo non accetta responsabilità alcuna per la mancata conformità alle normative di protezione dovuta a modifiche non consigliate al prodotto,
compresa l’installazione di schede e componenti di marca diversa da Lenovo.
Le prove effettuate sul presente prodotto hanno accertato che esso rientra nei limiti stabiliti per le apparecchiature di informatica Classe B ai sensi del
Norma Europea EN 55022. I limiti delle apparecchiature della Classe B sono stati stabiliti al fine di fornire ragionevole protezione da interferenze
mediante dispositivi di comunicazione in concessione in ambienti residenziali tipici.
Korea Class B Compliance
Japan VCCI Class B Compliance
Japanese statement of compliance for products less than or equal to 20 A per phase
Lenovo product service information for Taiwan
32 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
34 ThinkPad DVD Ultrabay Slim Burner User ’Gs uide
Part Number: 41N5647
Printed in USA
(1P) P/N: 41N5647
|
