CARE AND OPERATION
INSTRUCTIONS
STANDARD SERIES
36" and 42" Wood Burning Fireplaces
P/N 725,041M REV. A 02/2008
MODELS
BR-36/42
BC-36/42
BRI-36/42
BR-36/42-2
BRI-36/42-2
BCI-36/42
BC-36/42-2
BCI-36/42-2
The information contained in this manual applies to all model fireplaces
identified on this page. This information will help you obtain safe and
dependable service from your Superior fireplace system. Keep this
document in a safe place for future reference.
BC-42
Before you start your first fire, read this Care and Operations Manual
carefully to be sure you understand your fireplace system completely.
Failuretofollowthesesuggestionscouldresultinhazardousoperationor
fireplacemalfunction, creatingaseriouspotentialforpersonalinjuryand/
or property damage.
If you have any questions regarding the safe use or operation of your
fireplace, contact your local Superior distributor, your contractor/builder
or Superior Fireplace.
BC-36
WH Report No. J99025865A-231
RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE
OTL Report No. 116-F-43-2
US
This fireplace has been tested and approved for
use with a decorative gas appliance incorporating
an automatic shut-off device and complying with
the Standard for Decorative Gas Appliances for
installationinventedfireplaces,ANSIZ21.60(1991)
or American Gas Association draft requirements
for Gas-Fired Log Lighters for Wood Burning
Fireplaces, Draft No. 4 dated August, 1993.
The amount of heat available from the logs will
be about equal on a weight basis. However,
logsaregenerallynotweighedsotheamountof
heat will depend on:
6. Most wood needs to be seasoned 9 to 12
months to reduce the moisture content and
produce good steady fires. When moisture
content is reduced from 60 to 20%, the gain in
heat potential is nearly 7%.
1. The type of wood used.
2. How dry it is.
3. How many logs you put in.
4. The size of the logs.
7. Proper storage of wood, especially during
seasoning,isessential.Werecommendthatyou:
Decorative gas appliances may be installed in
these fireplaces. Installation must be in accor-
dance with the National Fuel Gas Code, ANSI
Z223.1 for compliance with the revised U.L.
127 Standard.
a. Never store wood on the ground. This will
causerottingandinsectinfiltration.Raisewood
on flat rock or scrap wood.
The last statement means that one big log
weighing 10 pounds has as much heating po-
tential as 10 pounds of twigs. However, air
cannot get at the solid log to feed the fire so the
solid log will burn slowly. While you would get
the same amount of heat out of either fire, the
smaller the pieces of wood and the more air
spacearoundthem, thefasterthefirewillburn.
b. Stack wood loosely to allow air circulation.
c. Store wood where it will not be excessively
exposed to weather, such as under a tarp or
under a roof.
CAUTION: WHEN USING A DECORATIVE
GAS APPLIANCE, THE FIREPLACE
DAMPER MUST BE SET TO THE FULLY
OPEN POSITION.
d. Do not stack wood directly against the walls
of your home.
DISPOSAL OF ASHES
Thisfireplacehasbeentestedandapprovedto
ANSI/IAS/AGA Z21.11.2 for use with an
unvented gas appliance having a maximum
rating of 26,000 BTU and complies with the
StandardforFactory-BuiltFireplaces,U.L.127,
wheninstalledwithunventedgaslogsets. The
limit may be increased to 40,000 BTU provid-
ingthat minimumcombustiblemantleheights
were increased to at least 18 inches when the
fireplace was installed.
Ashes should be placed in a metal container
with a tight fitting lid. The closed container of
ashes should be placed on a noncombustible
floor or on the ground, well away from all
combustible materials, pending final disposal.
Iftheashesaretobedisposedofbyburialinsoil
or other wise locally dispersed, they should be
retainedintheclosedcontaineruntilallcinders
have thoroughly cooled.
8. Be a knowledgeable wood buyer. There is a
difference in cord sizes. A standard cord stack
of logs is 4 ft. high by 8 ft. long by 4 ft. deep or
theequivalentofthiscubicfootage,(Figure1).
Standard
Cord of
Wood
8'
SOFTWOOD VS HARDWOOD
Prior to installing any gas log set, (Vented or
Unvented) refer to the fireplace installation
instructions for verification of mantle heights
andplacementofcombustiblematerialsaround
the firebox opening. NEVER INSTALL AN
UNVENTED GAS LOG SET WITH A BTU RAT-
ING GREATER THAN 26,000 IF THE
COMBUSTIBLE MANTLE PROJECTIONS ARE
LOWER THAN 18 INCHES ABOVE THE FIRE-
PLACE OPENING. Vented gas log sets do not
haverestrictionsplacedupontheirBTUrating.
Softwoods contain about 15 percent highly
flammableresinwhichgeneratescreosotesoot
in the chimney flue. Burning softwood exclu-
sively may not be as desirable nor as safe as
burning denser hardwoods. Many experienced
fire-builders use small amounts of softwood
kindling and newspaper in conjunction with
startingafirewithsplithardwoodlogs.Hereare
some guidelines to remember:
4'
4'
Figure 1
A face cord is the same height and length as a
standard cord but the depth is only the length
of the logs (12, 18 or 24 inches). A face cord
can contain as little as 25% of the wood found
in a standard cord.
1. Softwoods produce fast warming and shorter
fires. Hardwoods burn less vigorously, have
shorterflamesandproducesteady,glowingcoals.
Note: Units designated with the -2 suffix have
not been tested or approved for use with vent
free log sets.
2. As a general rule, denser woods contain
morepotentialheatperpound.Mostsoftwoods
offer moderate heat value per pound.
Wood Fuel Pointers
If you buy by the ton, remember that wood
becomes lighter as it dries. When buying green
or wet wood, ask for some extra poundage to
allow for the extra water you will be getting.
Wood is a wonderful renewable fuel source.
Normally it burns clean, leaving only a minimum
of waste ash, provides comforting heat and can
provide a variety of aromas and visual images.
3. Differentwoodsvarywidelyinflameheights,
flame intensities, smoke characteristics and in
sparking. Most hardwoods do not spark.
9. When comparing woods of the same mois-
ture content and same species, we find most
woods have approximately the same heating
potential per pound.
Youwillwanttoknowwhichwoodsarebestfor
use. Sometimes you may want a quick, short
fire to offset a morning chill. Soft woods are
preferable in this case. Other times you would
want more slow burning and a uniform heat
output. Hardwoods are preferable for this use.
4. Most freshly cut “green” wood will not burn
well and will smoke. Green wood can be from
10 to 40 percent less efficient than air-dried
seasoned wood.
However, most wood is sold by volume, not by
weight. To determine the best heating source,
look at the density of various wood types. (Den-
sity is the weight for a given size). The higher the
density, the more potential heat output.
5. Moistureandresinfoundinsideunseasoned
wood cells will build up pressure under heat
and explode as sparks.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
3
Astandardcordhasavolumeof128cubicfeet.
This figure also includes the air space between
and around the wood. The actual volume in a
standardcordisbetween60and100cubicfeet;
depending on how tightly the wood is packed.
Assumingthatyouarecomparingtwostandard
cords of different species but the same volume
and moisture content, the denser species will
providemoreBTU’s.Thetableofwoodspecies/
densities reveals more helpful guidelines.
DAMPER CONTROL
WARNING: IF YOUR FIREPLACE IS
EQUIPPED WITH GLASS DOORS, IT
SHOULD BE OPERATED WITH THE
DOORSFULLYOPENORFULLYCLOSED.
IF THE DOORS ARE LEFT PARTIALLY
OPEN, GASANDFLAMESMAYBEDRAWN
OUTOFTHEOPENING, CREATINGRISKS
OF BOTH FIRE AND SMOKE. REFER TO
FIGURES 3 AND 4 FOR PROPER OPER-
ATING CONDITIONS.
This fireplace is fitted with a manually con-
trolledchimneydamper. Thechimneydamper
should be closed when the fireplace is not in
use to prevent cold air from entering the home
through the chimney system.
The damper is controlled through the use of a
control lever located within the firebox open-
ing at the top center just behind the firebox
lintel (Figure 2 ). The control lever snaps into
place at the extreme range of motion, up and
back in the closed position. When pulled
forward and down, the damper is open.
HARDWOODS
DENSITY
Alser, Red
Ash
Aspen
Basswood, American
Beech, American
Birch
.41
.49-.60
.38-.39
.37
.64
.55-.65
.38
Damper
Closed
Damper
Open
Butternut
Cherry, Black
Chestnut, American
Cottonwood
Elm
Hackberry
Hickory, Pecan
Hickory, True
Honey locust
Locust, Black
Magnolia
.50
.43
Glass Doors
Fully Open or
Fully Closed
Lintel
.34-.40
.60.63
.53
.60.66
.69-.75
.66 (est.)
.69
.48-.50
.48-.63
.59-.67
.64-.88
.42
(Bi-Fold Doors)
Combustion
Air Actuator
Figure 3
Figure 2
Maple
Oak, Red
Oak, White
Poplar
The appliance flue damper must always re-
main open when operating.
Sassafras
.42
.52
.49
.64 (est.)
.50
2. The grate in the firebox should be centered
on or over the bottom hearth so your fire can
breath properly. Crumble and twist plenty of
newspapers UNDER the grate and criss-cross
some small dry kindling sticks on top of the
paper or on the bottom of the grate.
Sweet gum
Sycamore, American
Tanoak
Tupelo
Walnut, Black
Willow, Black
Glass Doors
Fully Open or
Fully Closed
(Twin-Pane Doors)
.55
.39
Figure 4
SOFTWOODS
DENSITY
3. Build a pyramid of three split logs (split will
start much faster). Arrange the uneven wood
to provide plenty of air space between.
CAUTION: IF A SMOKING CONDITION EX-
ISTS, GLASSDOORSSHOULDBECLOSED
DURING FIREPLACE OPERATION.
Bald cypress
Cedar
Douglas Fir
Fir
Hemlock
Larch, Western
Pine
Redwood
Spruce
.46
.31-.47
.46-.50
.32-.43
.40-.45
.52
.39-.59
.35-.40
.35-.41
.53
4. Now, light the paper at both sides of the
firebox.
Care and Cleaning of Your Glass Doors
Never clean the glass when the doors are hot.
Do not use ammonia or ammonia based glass
or household cleaner to clean the glass or the
door frame. An ammonia based cleaner will
damage the finish of the glass door.
5. Close the screens to prevent the escape of
sparks and embers.
Tamarack
6. Close the damper only when your fire is
completelyoutandashesarecold.Keepclosed
when fireplace is not in use to prevent unnec-
essary loss of heated or cooled air.
STARTING A FIRE
Clean the glass doors by wiping with a damp
towel followed by a clean dry towel to remove
streaks.
1. To start a fire in a the fireplace properly, first
check the operation of the flue damper.
GLASS DOOR OPERATING SAFETY
PRECAUTIONS AND INSTRUCTIONS
Remove stubborn stains from the glass with a
mild soap solution and a towel dampened with
clean water. Dry with a clean dry towel.
2. To prevent smoking at start-up, close any
window located near the fireplace when first
lighting a fire. The closed windows may be
reopened once a chimney draft is drawn in the
fireplace.
These fireplaces may be equipped with glass
doors. Refer to the end of this document for a
listingoftheglassdoorsapprovedforusewith
these fireplaces.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
4
• The fire must always be confined within the
boundaries of the fuel grate.
To "lock" the combustion air door closed, ensure
theactuatorispushedallthewayback,thenpush
the end of the actuators to the right until the step
in the actuator moves behind the fireplace front
face within the slotted opening.
COMBUSTION AIR
Aproperamountofcombustionairisimportant
for your fireplace. Fireplaces consume large
amounts of oxygen. It is important to allow an
adequate supply of air.
• The fireplace screens must always be closed
whenever the fireplace is being used.
Combustion Air
Actuator
•Neverslamtheglassdoorsinceitcouldcause
the glass to break.
If the fireplace is not equipped with an outside
air kit, it may not obtain sufficient amounts of
combustion air from inside the house or struc-
ture in which it is installed. Therefore, the fire
may draw from an outside air source and pull
air in through the chimney. This may cause
smoke spillage into the room.
• Do not build excessively large or hot fires —
scorching or discoloring of the plated brass
trim may occur.
•Extremetemperaturechangescancauseglass
breakage—donotbuildahotfireandclosethe
glass doors if the doors are cold.
Smoke spillage often occurs when a fire is first
started, until the fireplace and the chimney has
had the opportunity to “come up to tempera-
ture” and to begin to function normally. If
smoke spillage problems persist, a window
may be opened just a crack to allow the proper
flow of combustion air to the fireplace.
•Ifthetemperedglasspanebecomesscratched
or chipped, it creates a weakness in the glass
which can cause the glass to break when
heated. Replace the pane of glass by contact-
ing your nearest dealer.
CAUTION: GLASS AND METAL FRAMES
GET HOT — ALWAYS USE HANDLES TO
OPEN AND CLOSE THE DOORS.
If your fireplace is equipped with an outside
combustion air kit, keep it open at all times
when fire is burning and close when fire is out
to prevent cold air intrusion.
Pull Forward to Open,
Push Back to Close
Figure 5
WARNING: BE AWARE THAT SAFETY
GLASS IS UNPREDICTABLE WHEN HOT
ANDMAYBREAK, EXPELLINGHOTGLASS
INTO THE ROOM. ADVISE ALL FAMILY
MEMBERS TO REMAIN WELL AWAY
FROM THE FIREPLACE WHEN OPERAT-
ING WITH DOORS CLOSED TO AVOID
ANY POSSIBLE PERSONAL INJURY.
Combustion Air Control
REFRACTORIES
The actuator for combustion air system is
standard on all fireplaces but must not be
operated if the complete system is not in-
stalled. See Figure 5 and refer to Figure 2.
All fireboxes contain a furnace refractory floor,
sides and back. These refractories are rein-
forcedwithsteel,butcanbebrokenbyimproper
use. Dropping logs on the bottom refractory
and building fires directly against the refracto-
ries can cause premature burnout of these
components. It may easily be repaired or re-
placedatcostsfarbelowrepairandmaintenance
for masonry fireplaces.
If you have reason to believe that you do not
have a complete outside combustion system,
contact your distributor to have your fireplace
inspected for the presence of the complete
system before you use the combustion air
actuator. DO NOT assume that you have this
systeminplacebecauseyouhaveanactuating
lever present on your fireplace front face.
IMPORTANT: Plated polished brass glass
doors may have a plastic covering over all
brass pieces for protection during shipping
and handling. The plastic covering should be
removedbeforeinstallationoftheglassdoors.
Under the plastic covering is a protective
lacquercoatingwhichshouldnotberemoved.
In some instances, if it is removed, irrevers-
ible damage to the brass finish could occur.
Refertothefollowingforspecificinformation
on plated polished brass.
Proper care and “burn-in” of the firebox will
prolong the period of enjoyment without exten-
sive maintenance. For the first few uses, build
small fires – not roaring infernos. The materials
usedintherefractoriescontainandabsorbmois-
ture. It is important to “cure” the refractories by
buildingonlymodestfires. Undernormalusage,
it is expected that hairline cracks will appear in
the refractory surface. These hairline cracks do
not affect the safe operation of the fireplace.
WARNING: DO NOT OPERATE THE COM-
BUSTION AIR ACTUATOR UNLESS A
COMPLETE OUTSIDE COMBUSTION AIR
VENT SYSTEM HAS BEEN INSTALLED
WITH YOUR FIREPLACE.
IMPORTANT: Thelacquer coatingonthepol-
ished brass glass doors and trim pieces can
be damaged or removed causing corrosion
and/or tarnish. Do not remove the protective
lacquer coating from plated polished doors
and trim. To help protect the finish; use a
non-acidic wax and avoid the over-spray of
acidic/alkali based glass cleaners on the
brass pieces. Please understand that the
heat of the fire will cause the protective
lacquer finish to slightly change to a light
caramel color. Do not be alarmed as this is
a normal occurrence.
To provide outside combustion air to your
fireplace while it is in operation, locate the
combustion air actuator along the right side of
the fireplace opening behind the screen.
Refractories should be replaced when:
1. The crack opens more than 1/4" (19 mm).
2. Pitting in the surface is extensive and pits
become deeper than 3/16" (4.76 mm).
To operate, push the end of the actuator to the
left as shown in Figure 5, until it "pops" free of
its "locked" position. Pull the actuator forward
to open the combustion air door, and push it
back to close.
3. Anypieceofrefractorylargerthan2"(51mm)
in radius and 3/16" deep becomes dislodged.
If conditions 1, 2 or 3 occur, the refractory
should be replaced.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
5
If your do not have glass doors installed, a
dampsheetcoveringthefireplaceopeningand
sealed with masking tape will do. Then clean
thefluefromthetopdown(ifanoffsetsystem,
clean per Step 2) using a proper size chimney
brush with flexible pole sections. Don’t open
thedoorsorremovethesheetuntilallsoothas
settled. Vacuum, don’t sweep.
MAINTENANCE GUIDELINES
TROUBLESHOOTING
No Smoking Allowed
Your fireplace is designed to operate trouble-
free with minimum maintenance. However, like
any fine appliance, it deserves and requires
some housekeeping attention.
Your new fireplace is designed not to smoke if
properlyinstalledandoperatedperourinstruc-
tions. If you do experience a problem, here are
several things to check:
Your fireplace will perform better – and cer-
tainly look more attractive to family and friends
–ifitiscleanedbeforeeachuse. Beforethefirst
seasonal use in Autumn and after the last fire in
Spring, it is important to inspect the fireplace
system carefully. We recommend at least two
complete fireplace inspections a year.
1. Remember – always check to ensure your
flue damper is in the open position before
lighting a fire!
4. Check the metal flashing and seals around
your chimney. Seal any cracks or loose nail-
head openings to prevent roof leaks.
2. When lighting your fire, a little smoke may
escape into the room – more likely if the chim-
ney is cold. To correct this, hold a lighted
newspaper up inside the firebox near the open
flue damper. This will turn around any down-
draft and clear the flue of cold air. As your log
fireburnsbelow,theupdraftwillimproveasthe
chimney heats up.
5. Clean the firebox thoroughly by using a soft
brush or equivalent.
Before Each Use
WARNING: CONTINUED OVERFIRING
CAN PERMANENTLY DAMAGE YOUR
FIREPLACE SYSTEM. SOME EXAMPLES
OF OVERFIRING ARE:
1. Clean the firebox of excessive ashes. Some
owners prefer to leave a small layer to insulate
the cold refractory below the grate which helps
fire starting.
3. Is your fire too far forward? Move it toward
the back with your poker. Keep the fire well
within the confines of your fuel grate.
• BURNING QUANTITIES OF SCRAP
LUMBER, PINEBRANCHES, PAPEROR
CARDBOARD BOXES WHICH EXCEED
THE VOLUME OF THE NORMAL LOG
FIRE.
This fireplace has a factory supplied grate at-
tached, it is permissible to remove the grate for
cleaning; however, the grate must be re-at-
tached to the fireplace before the next burn.
4. Keep your fire up on the grate and the
refractory below free of excessive ashes. The
fire needs plenty of air movement around the
logs.
2. Keep the fireplace screens clean so combus-
tion air flows freely.
• BURNING TRASH, CHEMICALS OR
CHEMICALLY TREATED COMBUS-
TIBLES.
5. If smoking occurs an hour or two after
lighting the fire, perhaps your well-insulated
house is too airtight and there is scarcely any
way for replacement air to enter and feed the
fire.Checktoseeifyouroutsidecombustionair
kit(ifinstalled)isopen.Checkoutsidetoensure
noobstructionsareinfrontofexteriorairentry.
Open a window slightly, open doors to one or
two rooms and see if this stops the smoking.
3. Spot check the brick-like refractory for small
cracks. Heat from the fire expands it slightly.
When it cools, it contracts.
CREOSOTE FORMATION AND REMOVAL
TWICE A YEAR CHECK-UP
When wood is burned slowly, it produces tar
and other organic vapors, which combine with
expelled moisture to form creosote. The creo-
sote vapors condense in the relatively cool
chimneyflueofaslow-burningfire. Asaresult,
creosote residue accumulates on the flue lin-
ing. When ignited, this creosote makes an
extremely hot fire.
Normally, twiceayear, youshouldinspectyour
fireplace following this list:
6. Is a vent fan, exhaust hood or central
heating/cooling system stealing combustion
air from your fireplace? If their volume is high
enough, this can cause negative pressure and
an unwanted downdraft – and smoking.
1. Inspect the opening in your chimney top and
remove any debris that could clog it. The cap is
usually held in place by four (4) screws, which
remove easily for checking or cleaning the full
length of the flue from above. Remove the
chimney top while wearing gloves to guard
against any sharp metal edges.
The chimney should be inspected at least twice
yearly during the heating season to determine
if a creosote build-up has occurred.
7. Is your wood fuel too wet or unseasoned?
Or does it contain some chemical substance
that causes sputtering, smoking and toxic
fumes?
2. Inspect the entire flue from the top down for
obstructions such as birds nests, leaves, etc.
This may be done by using a flexible handled
chimney cleaning brush. If the chimney con-
tainsoffset/returnelbows;asoftbrushcleaning
from the top down to any elbow and then from
the firebox up to the offset/return section is the
proper method. The beam from a powerful
flashlight will help in this inspection.
If creosote has accumulated, it should be re-
moved to reduce the risk of a chimney fire.
8. Figure 6 illustrates the correct height of
your chimney top. It is unlikely that your instal-
lation does not adhere to the installation
instructions. However, ifnotcorrect, youcould
experience an unusual downdraft. Usually, the
best solution is to increase the chimney height.
This may also be necessary if nearby trees,
adjoining roof lines or a hill is causing a down-
draft condition.
Ifcreosotebuild-upisfound,donotusechemi-
cal chimney cleaners that are poured on a hot
fire. The chemical cleaners can be dangerous
and generally only work on the flue section
nearest the fire, leaving the rest of the flue
unaffected.Itisbesttotakethetimetocleanthe
flue as previously described or have the chim-
ney professionally cleaned by a qualified
chimney sweep.
3. Look up from inside the fireplace (damper
open) to see any obstructions in the lower flue
area. Ifpresent, shutthedamperandglassdoors
(if installed) to seal the firebox and contain any
soot that might fall.
9. Remember, your fireplace has been de-
signed as a supplemental heating device only,
it is not intended to heat your entire home.
6
Less Than 10'
ACCESSORY COMPONENTS
2' Min.
3' Min.
2' Min.
10'
3' Min.
Figure 6
WARRANTY
42 ABF/36 ABF
42 ABF-BB/36 ABF-BB
42 ABF-P/36 ABF-P
This fireplace is covered by a limited warranty detailed separately from this document.
Retain this manual. File it with your other documents for future reference.
PRODUCT REFERENCE INFORMATION
Bi-Fold Doors
Bi-Fold Doors
Your fireplace can be fitted with beautiful bi-
fold doors. Model ABF doors are available for
use with these fireplace. Doors are easily fitted
to the fireplace opening. Use Model 36 doors
with36inchfireplacesandModel42doorswith
42inchfireplaces. ModelABFdoorscomewith
standard black finish. Model ABF-BB doors
haveabeautifulbrightbrassfinish. ModelABF-
P doors have a platinum finish.
We recommend that you record the following important information about your fireplace. Please
contactyourLennoxdealerforanyquestionsorconcerns. ForthenumberofyournearestLennox
dealer, please call 1-800-9-LENNOX
Your Fireplace's Model Number _______________________________________
Your Fireplace's Serial Number ________________________________________
The Date On Which Your Fireplace Was Installed __________________________
Your Dealer's Name_________________________________________________
REPLACEMENT PARTS
ACCESSORY COMPONENTS
(FBK-200 Models Only)
A complete parts list is found at the end of this
manual. Use only parts supplied from the
manufacturer.
Normally, all parts should be ordered through
yourSuperiordistributorordealer.Partswillbe
shipped at prevailing prices at time of order.
42 TPA-BB
36 TPA-BB
When ordering repair parts, always give the
following information:
Twin Pane Doors
Forced Air Blower Kits
-Single Speed
-Variable Speed
FBK-100
FBK-200
FUBSK
Twin Pane Doors
1. The model number of the appliance.
2. The serial number of the appliance.
3. The part number.
4. The description of the part.
5. The quantity required.
Unit Mounted Blower Switch Kit
Your fireplace can be fitted with beautiful twin
pane doors. Model TPA doors are available for
use with these fireplace. Use Model 36 doors
with36inchfireplacesandModel42doorswith
42 inch fireplaces. Model TPA doors are easily
fitted to the fireplace opening. Model TPA-BB
doors have a beautiful bright brass finish.
Blower Kit
The FBK-100 blower provides for a constant
velocity forced air circulation feature for your
appliance. The FBK-200 assembly with vari-
able speed wall switch provides a forced air
circulation feature for your appliance. When
installing the FBK-100 Blower Kit, a Blower
Switch Kit (Model FUBSK) is required. This
switch kit allows for a unit mounted blower
switch to be used. The FUBSK is not included
and must be purchased separately.
6. The installation date of the appliance.
To ensure warranty and to prevent a potential
fire hazard, do not use any other doors on
these appliances.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
7
REPLACEMENT PARTS
3
2
4
1
5
Models 42
3
6
4
6
5
Models 36
Models 36
Models 42
Part No. Qty.
No.
DESCRIPTION
Gas Fireplace Assembly
Firescreen
Part No. Qty.
–
–
2
2
2
1
1
1
–
–
2
2
2
1
1
1
1.
2.
3.
4.
5.
6.
161136
88L95
161108
88L95
Rod, Screen
Refractory, Side
Refractory, Rear
Refractory Base
Grate
LB-96795
LB-96796
LB-96794
87L20
LB-96798
LB-96799
LB-96797
87L21
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
The manufacturer reserves the right to make changes at any time, without notice, in design,
materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2007 by LENNOX HEARTH PRODUCTS
1110 West Taft Avenue
Orange, CA 92865
P/N 725,041M REV. A 02/2008
|